- 您現在的位置：買賣IC網 > PDF目錄362139 > ADNS-6230-001 Low Power Laser Mouse Bundles PDF資料下載
參數資料
| 型號： | ADNS-6230-001 |
| 英文描述： | Low Power Laser Mouse Bundles |
| 中文描述： | 低功率激光鼠標捆綁 |
| 文件頁數： | 22/45頁 |
| 文件大?。?/td> | 790K |
| 代理商： | ADNS-6230-001 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁當前第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁
22
Motion
Access: Read/Write
Address: 0x02
Reset Value: 0x00
Bit
7
6
5
4
3
2
1
0
Field
MOT
PIXRDY
PIXFIRST
OVF
LP_VALID
FAULT
Reserved
Reserved
Data Type
: Bit field.
USAGE: Register 0x02 allows the user to determine if motion has occurred since the last time it
was read. If the MOT bit is set, then the user should read registers 0x03 and 0x04 to get the
accumulated motion. Read this register before reading the Delta_X and Delta_Y registers.
Writing anything to this register clears the MOT and OVF bits, Delta_X and Delta_Y registers. The
written data byte is not saved.
Internal buffers can accumulate more than eight bits of motion for X or Y. If either one of the
internal buffers overflows, then absolute path data is lost and the OVF bit is set. To clear
theoverflow, write anything to this register.
Check the OVR bit if more than 4" of motion is accumulated without reading it. If bit set, discard
the motion as erroneous. Write anything to this register to clear the overflow condition.
The PIXRDY bit will be set whenever a valid pixel data byte is available in the Pixel_Dump
register. Check that this bit is set before reading from Pixel_Dump. To ensure that the Pixel_Grab
pointer has beenreset to pixel 0,0 on the initial write to Pixel_Grab, check to see if PIXFIRST is
set to high.
NOTE: Agilent recommends that registers 0x02, 0x03 and 0x04 be read sequentially.
Field Name
Description
MOT
Motion since last report
0 = No motion
1 = Motion occurred, data ready for reading in Delta_X and Delta_Y registers
PIXRDY
Pixel Pump data byte is available in Pixel_Dump register
0 = data not available
1 = data available
PIXFIRST
This bit is set when the Pixel_Grab register is written to or when a complete pixel array
has been read, initiating an increment to picel 0,0.
0 = Pixel_Grab data not from pixel 0,0.
1 = Pixel_Grab data is from pixel 0,0.
Motion overflow,
Y and/or
X buffer has overflowed since last report
0 = no overflow
1 = Overflow has occurred
OVF
LP_VALID
Laser Power Settings
0 = register 0x1a and register 0x1f or register 0x1c and register 0x1d do not have
complementary values
1 = laser power is valid
FAULT
Indicates that XY_LASER is shorted to GND or VDD
0 = no fault detected
1 = fault detected
相關PDF資料 |
PDF描述 |
|---|---|
| ADNV-6330 | Low Power Laser Mouse Bundles |
| ADNK-2051 | Reference Design Kit for Corded Optical Mouse |
| ADNK-2623 | Optical Mouse Designer＇s Kit |
| ADNS-2620 | Small Form Factor. Entry-Level Optical Mouse Sensor with Performance Features |
| ADNK-2620 | Solid-State Optical Mouse Sensor |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADNS-6530 | 功能描述:光學導航傳感器 COB Sensor RoHS:否 制造商:Avago Technologies 工作電源電壓: 封裝 / 箱體: 最大工作溫度: 最小工作溫度: |
| ADNS-7010 | 功能描述:光學導航傳感器 Laser Sensor RoHS:否 制造商:Avago Technologies 工作電源電壓: 封裝 / 箱體: 最大工作溫度: 最小工作溫度: |
| ADNS-7050 | 功能描述:光學導航傳感器 Laser Sensor RoHS:否 制造商:Avago Technologies 工作電源電壓: 封裝 / 箱體: 最大工作溫度: 最小工作溫度: |
| ADNS-7100-001 | 功能描述:光學導航傳感器 Lens for ADNS-7630 RoHS:否 制造商:Avago Technologies 工作電源電壓: 封裝 / 箱體: 最大工作溫度: 最小工作溫度: |
| ADNS-7530 | 功能描述:光學導航傳感器 Mouse sensor RoHS:否 制造商:Avago Technologies 工作電源電壓: 封裝 / 箱體: 最大工作溫度: 最小工作溫度: |
發布緊急采購，3分鐘左右您將得到回復。