- 您現在的位置：買賣IC網 > PDF目錄362139 > ADNS-6130-001 Low Power Laser Mouse Bundles PDF資料下載
參數資料
| 型號： | ADNS-6130-001 |
| 英文描述： | Low Power Laser Mouse Bundles |
| 中文描述： | 低功率激光鼠標捆綁 |
| 文件頁數： | 8/45頁 |
| 文件大小： | 790K |
| 代理商： | ADNS-6130-001 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁
8
LASER Output Power
The laser beam output power
as measured at the navigation
surface plane is specified
below. The following conditions
apply:
1. The system is adjusted
according to the above
procedure.
2. The system is operated
within the recommended
operating temperature range.
3. The V
DD
value is no greater
than 300mV above its value
at the time of adjustment.
4. No allowance for optical
power meter accuracy is
assumed.
Figure 6. Single Fault Detection and Eye-safety Feature Block Diagram
LASER_NEN
XY_LASER
GND
ADNS-6030
LASER
DRIVER
V
DD
VCSEL
Microcontroller
Serial port
voltage sense
current set
V
DD
fault control
block
Disabling the LASER
LASER_NEN is connected to
the gate of a P-channel
MOSFET transistor which when
ON connects V
DD
to the
LASER. In normal operation,
LASER_NEN is low. In the
case of a fault condition
(ground or V
DD
at XY_LASER),
LASER_NEN goes high to turn
the transistor off and
disconnect V
DD
from the
LASER.
Single Fault Detection
ADNS-6030 is able to detect a
short circuit or fault condition
at the XY_LASER pin, which
could lead to excessive laser
power output. A path to
ground on this pin will trigger
the fault detection circuit,
which will turn off the laser
drive current source and set
the LASER_NEN output high.
When used in combination
with external components as
shown in the block diagram
below, the system will prevent
excess laser power for a
resistive path to ground at
XY_LASER by shutting off the
laser. In addition to the
ground path fault detection
described above, the fault
detection circuit is
continuously checked for
proper operation by internally
generating a path to ground
with the laser turned off via
LASER_NEN. If the XY_LASER
pin is shorted to V
DD
, this test
will fail and will be reported
as a fault.
相關PDF資料 |
PDF描述 |
|---|---|
| ADNS-6230-001 | Low Power Laser Mouse Bundles |
| ADNV-6330 | Low Power Laser Mouse Bundles |
| ADNK-2051 | Reference Design Kit for Corded Optical Mouse |
| ADNK-2623 | Optical Mouse Designer＇s Kit |
| ADNS-2620 | Small Form Factor. Entry-Level Optical Mouse Sensor with Performance Features |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADNS-6150 | 功能描述:光學導航傳感器 Small Lens RoHS:否 制造商:Avago Technologies 工作電源電壓: 封裝 / 箱體: 最大工作溫度: 最小工作溫度: |
| ADNS-6160-001 | 功能描述:光學導航傳感器 Trim Lens RoHS:否 制造商:Avago Technologies 工作電源電壓: 封裝 / 箱體: 最大工作溫度: 最小工作溫度: |
| ADNS-6170-002 | 功能描述:光學導航傳感器 Wide Trim Lens RoHS:否 制造商:Avago Technologies 工作電源電壓: 封裝 / 箱體: 最大工作溫度: 最小工作溫度: |
| ADNS-6180-001 | 功能描述:光學導航傳感器 Trim lens for A7700 RoHS:否 制造商:Avago Technologies 工作電源電壓: 封裝 / 箱體: 最大工作溫度: 最小工作溫度: |
| ADNS-6180-002 | 功能描述:光學導航傳感器 Wide Trim Lens for A7700 RoHS:否 制造商:Avago Technologies 工作電源電壓: 封裝 / 箱體: 最大工作溫度: 最小工作溫度: |
發布緊急采購，3分鐘左右您將得到回復。