- 您現在的位置：買賣IC網 > PDF目錄362139 > ADNS-6120 Low Power Laser Mouse Bundles PDF資料下載
參數資料
| 型號： | ADNS-6120 |
| 英文描述： | Low Power Laser Mouse Bundles |
| 中文描述： | 低功率激光鼠標捆綁 |
| 文件頁數： | 4/45頁 |
| 文件大?。?/td> | 790K |
| 代理商： | ADNS-6120 |
第1頁第2頁第3頁當前第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁
4
Assembly Recommendation
1. Insert the sensor and all
other electrical components
into the application PCB
(main PCB board and
VCSEL PCB board).
2. Wave-solder the entire
assembly in a no-wash
solder process utilizing a
solder fixture. The solder
fixture is needed to protect
the sensor during the solder
process. It also sets the
correct sensor-to -PCB
distance, as the lead
shoulders do not normally
rest on the PCB surface.
The fixture should be
designed to expose the
sensor leads to solder while
shielding the optical
aperture from direct solder
contact.
3. Place the lens onto the base
plate.
4. Remove the protective
kapton tape from the optical
aperture of the sensor. Care
must be taken to keep
contaminants from entering
the aperture.
5. Insert the PCB assembly
over the lens onto the base
plate. The sensor aperture
ring should self-align to the
lens. The optical position
reference for the PCB is set
by the base plate and lens.
Note that the PCB motion
due to button presses must
be minimized to maintain
optical alignment.
Figure 3. Recommended PCB mechanical cutouts and spacing
6. Remove the protective cap
from the VCSEL.
7. Insert the VCSEL assembly
into the lens.
8. Slide the clip in place until
it latches. This locks the
VCSEL and lens together.
9. Tune the laser output power
from the VCSEL to meet the
Eye Safe Class I Standard
as detailed in the LASER
Power Adjustment
Procedure.
10. Install the mouse top case.
There must be a feature in
the top case (or other area)
to press down onto the
sensor to ensure the sensor
and lens are interlocked to
the correct vertical height.
相關PDF資料 |
PDF描述 |
|---|---|
| ADNS-6130-001 | Low Power Laser Mouse Bundles |
| ADNS-6230-001 | Low Power Laser Mouse Bundles |
| ADNV-6330 | Low Power Laser Mouse Bundles |
| ADNK-2051 | Reference Design Kit for Corded Optical Mouse |
| ADNK-2623 | Optical Mouse Designer＇s Kit |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADNS-6130-001 | 功能描述:光學導航傳感器 Optical Mouse Lens RoHS:否 制造商:Avago Technologies 工作電源電壓: 封裝 / 箱體: 最大工作溫度: 最小工作溫度: |
| ADNS-6150 | 功能描述:光學導航傳感器 Small Lens RoHS:否 制造商:Avago Technologies 工作電源電壓: 封裝 / 箱體: 最大工作溫度: 最小工作溫度: |
| ADNS-6160-001 | 功能描述:光學導航傳感器 Trim Lens RoHS:否 制造商:Avago Technologies 工作電源電壓: 封裝 / 箱體: 最大工作溫度: 最小工作溫度: |
| ADNS-6170-002 | 功能描述:光學導航傳感器 Wide Trim Lens RoHS:否 制造商:Avago Technologies 工作電源電壓: 封裝 / 箱體: 最大工作溫度: 最小工作溫度: |
| ADNS-6180-001 | 功能描述:光學導航傳感器 Trim lens for A7700 RoHS:否 制造商:Avago Technologies 工作電源電壓: 封裝 / 箱體: 最大工作溫度: 最小工作溫度: |
發布緊急采購，3分鐘左右您將得到回復。