- 您現在的位置：買賣IC網 > PDF目錄362139 > ADNB-6032 Low Power Laser Mouse Bundles PDF資料下載
參數資料
| 型號： | ADNB-6032 |
| 英文描述： | Low Power Laser Mouse Bundles |
| 中文描述： | 低功率激光鼠標捆綁 |
| 文件頁數： | 16/45頁 |
| 文件大?。?/td> | 790K |
| 代理商： | ADNB-6032 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁
16
Power management modes
The ADNS-6030 has three
power-saving modes. Each
mode has a different motion
detection period, affecting
response time to mouse motion
(Response Time). The sensor
automatically changes to the
appropriate mode, depending
on the time since the last
reported motion (Downshift
Time). The parameters of each
mode are shown in the
following table.
Mode
Response
Time
(nominal)
Downshift
Time
(nominal)
Rest 1
33ms
237ms
Rest 2
164ms
8.4s
Rest 3
840ms
504s
Chip Select Operation
The serial port is activated
after NCS goes low. If NCS is
raised during a transaction,
the entire transaction is
aborted and the serial port
will be reset. This is true for
all transactions. After a
transaction is aborted, the
normal address-to-data or
transaction-to-transaction
delay is still required before
beginning the next transaction.
To improve communication
reliability, all serial
transactions should be framed
by NCS. In other words, the
port should not remain
enabled during periods of non-
use because ESD and EFT/B
events could be interpreted as
serial communication and put
the chip into an unknown
state. In addition, NCS must
be raised after each burst-
mode transaction is complete
to terminate burst-mode. The
port is not available for
further use until burst-mode is
terminated.
Synchronous Serial Port
The synchronous serial port is
used to set and read
parameters in the ADNS-6030,
and to read out the motion
information.
The port is a four-wire port.
The host micro-controller
always initiates communication;
the ADNS-6030 never initiates
data transfers. SCLK, MOSI,
and NCS may be driven
directly by a micro-controller.
The port pins may be shared
with other SPI slave devices.
When the NCS pin is high, the
inputs are ignored and the
output is tri-stated.
The lines that comprise the
SPI port:
SCLK: Clock input. It is
always generated by the
master (the micro-controller).
MOSI: Input data. (Master
Out/Slave In)
MISO: Output data. (Master
In/Slave Out)
NCS:
(active low). NCS needs to be
low to activate the serial port;
otherwise, MISO will be high Z,
and MOSI & SCLK will be
ignored. NCS can also be
used to reset the serial port in
case of an error.
Chip select input
Motion Pin Timing
The motion pin is a level-
sensitive output that signals the
micro-controller when motion
has occurred. The motion pin
is lowered whenever the
motion bit is set; in other
words, whenever there is data
in the Delta_X or Delta_Y
registers. Clearing the motion
bit (by reading Delta_X and
Delta_Y, or writing to the
Motion register) will put the
motion pin high.
LASER Mode
For power savings, the VCSEL
will not be continuously on.
ADNS-6030 will flash the
VCSEL only when needed.
相關PDF資料 |
PDF描述 |
|---|---|
| ADNS-6030 | Low Power Laser Mouse Bundles |
| ADNS-6120 | Low Power Laser Mouse Bundles |
| ADNS-6130-001 | Low Power Laser Mouse Bundles |
| ADNS-6230-001 | Low Power Laser Mouse Bundles |
| ADNV-6330 | Low Power Laser Mouse Bundles |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADNB-6032-EV | 功能描述:光學導航傳感器 Bundle w/Trim Lens RoHS:否 制造商:Avago Technologies 工作電源電壓: 封裝 / 箱體: 最大工作溫度: 最小工作溫度: |
| ADNB-6091 | 功能描述:光學導航傳感器 Mouse sensor RoHS:否 制造商:Avago Technologies 工作電源電壓: 封裝 / 箱體: 最大工作溫度: 最小工作溫度: |
| ADNB-6092 | 功能描述:光學導航傳感器 Mouse sensor RoHS:否 制造商:Avago Technologies 工作電源電壓: 封裝 / 箱體: 最大工作溫度: 最小工作溫度: |
| ADNB-6532 | 功能描述:光學導航傳感器 Bundle w/Trim Lens RoHS:否 制造商:Avago Technologies 工作電源電壓: 封裝 / 箱體: 最大工作溫度: 最小工作溫度: |
| ADNB-7011 | 功能描述:光學導航傳感器 Mouse sensor RoHS:否 制造商:Avago Technologies 工作電源電壓: 封裝 / 箱體: 最大工作溫度: 最小工作溫度: |
發布緊急采購，3分鐘左右您將得到回復。