- 您現在的位置：買賣IC網 > PDF目錄362139 > ADNB-6031 Low Power Laser Mouse Bundles PDF資料下載
參數資料
| 型號： | ADNB-6031 |
| 英文描述： | Low Power Laser Mouse Bundles |
| 中文描述： | 低功率激光鼠標捆綁 |
| 文件頁數： | 19/45頁 |
| 文件大?。?/td> | 790K |
| 代理商： | ADNB-6031 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁
19
Notes on Shutdown and Forced Rest
The ADNS-6030 can be set in
Rest mode through the
Configuration_Bits register
(0x11). This is to allow for
further power savings in
applications where the sensor
does not need to operate all
the time.
The ADNS-6030 can be set in
Shutdown mode by writing
0xe7 to register 0x3b. The SPI
port should not be accessed
when Shutdown mode is
asserted, except the power-up
command (writing 0x5a to
register 0x3a). (Other ICs on
the same SPI bus can be
accessed, as long as the
sensor’s NCS pin is not
asserted.) The table below
shows the state of various pins
during shutdown. To deassert
Shutdown mode:
1. Write 0x5a to register 0x3a
2. Wait for t
WAKEUP
3. Write 0xFE to register 0x28
4. Any register settings must
then be reloaded.
*
1
NCS pin must be held to 1
(high) if SPI bus is shared
with other devices. It is
recommended to hold to 1
(high) during Power Down
unless powering up the
Sensor. It must be held to 0
(low) if the sensor is to be
re-powered up from
shutdown (writing 0x5a to
register 0x3a).
*
2
Depend on last state
*
3
SCLK is ignore if NCS is 1
(high). It is functional if
NCS is 0 (low).
*
4
MOSI is ignore if NCS is 1
(high). If NCS is 0 (low),
any command present on
the MOSI pin will be
ignored except power-up
command (writing 0x5a to
register 0x3a).
Note: There are long wakeup
times from shutdown and
forced Rest. These features
should not be used for power
management during normal
mouse motion.
Notes on Power-up
The ADNS-6030 does not
perform an internal power up
self-reset; the
POWER_UP_RESET register
must be written every time
power is applied. The
appropriate sequence is as
follows:
1. Apply power
2. Drive NCS high, then low to
reset the SPI port
3. Write 0x5a to register 0x3a
4. Wait for t
WAKEUP
5. Write 0xFE to register 0x28
6. Read from registers 0x02,
0x03 and 0x04 (or read
these same 3 bytes from
burst motion register 0x42)
one time regardless of the
motion pin state.
During power-up there will be
a period of time after the
power supply is high but
before any clocks are available.
The table below shows the
state of the various pins
during power-up and reset.
Figure 21. Motion Burst Timing
Motion_Burst Register Address
Read First Byte
First Read Operation
Read Second Byte
SCLK
t
SRAD
Read Third Byte
相關PDF資料 |
PDF描述 |
|---|---|
| ADNB-6032 | Low Power Laser Mouse Bundles |
| ADNS-6030 | Low Power Laser Mouse Bundles |
| ADNS-6120 | Low Power Laser Mouse Bundles |
| ADNS-6130-001 | Low Power Laser Mouse Bundles |
| ADNS-6230-001 | Low Power Laser Mouse Bundles |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADNB-6031-EV | 功能描述:光學導航傳感器 Bundle w/Round Lens RoHS:否 制造商:Avago Technologies 工作電源電壓: 封裝 / 箱體: 最大工作溫度: 最小工作溫度: |
| ADNB-6032 | 功能描述:光學導航傳感器 Bundle w/Trim Lens RoHS:否 制造商:Avago Technologies 工作電源電壓: 封裝 / 箱體: 最大工作溫度: 最小工作溫度: |
| ADNB-6032-EV | 功能描述:光學導航傳感器 Bundle w/Trim Lens RoHS:否 制造商:Avago Technologies 工作電源電壓: 封裝 / 箱體: 最大工作溫度: 最小工作溫度: |
| ADNB-6091 | 功能描述:光學導航傳感器 Mouse sensor RoHS:否 制造商:Avago Technologies 工作電源電壓: 封裝 / 箱體: 最大工作溫度: 最小工作溫度: |
| ADNB-6092 | 功能描述:光學導航傳感器 Mouse sensor RoHS:否 制造商:Avago Technologies 工作電源電壓: 封裝 / 箱體: 最大工作溫度: 最小工作溫度: |
發布緊急采購，3分鐘左右您將得到回復。