- 您現在的位置：買賣IC網 > PDF目錄374016 > ADN2811 (Analog Devices, Inc.) OC-48/OC-48 FEC Clock and Data Recovery IC with Integrated Limiting Amp PDF資料下載
參數資料
| 型號： | ADN2811 |
| 廠商： | Analog Devices, Inc. |
| 元件分類： | 運動控制電子 |
| 英文描述： | OC-48/OC-48 FEC Clock and Data Recovery IC with Integrated Limiting Amp |
| 中文描述： | OC-48/OC-48 FEC的時鐘和數據恢復IC，集成了限幅放大器 |
| 文件頁數： | 8/16頁 |
| 文件大?。?/td> | 359K |
| 代理商： | ADN2811 |
REV. A
–8–
ADN2811
JITTER SPECIFICATIONS
The ADN2811 CDR is designed to achieve the best bit-error-rate
(BER) performance and has exceeded the jitter generation, trans-
fer, and tolerance specifications proposed for SONET/SDH
equipment defined in the Telcordia Technologies specification.
Jitter is the dynamic displacement of digital signal edges from
their long-term average positions measured in UI (unit intervals),
where 1 UI = 1 bit period. Jitter on the input data can cause
dynamic phase errors on the recovered clock sampling edge.
Jitter on the recovered clock causes jitter on the retimed data.
The following section briefly summarizes the specifications of
the jitter generation, transfer, and tolerance in accordance with
the Telcordia document (GR-253-CORE, Issue 3, September
2000) for the optical interface at the equipment level and the
ADN2811 performance with respect to those specifications.
Jitter Generation
The jitter generation specification limits the amount of jitter
that can be generated by the device with no jitter and wander
applied at the input. For OC-48 devices, the band-pass filter has
a 12 kHz high-pass cutoff frequency with a roll-off of 20 dB/
decade and a low-pass cutoff frequency of at least 20 MHz. The
jitter generated should be less than 0.01 UI rms and less
than 0.1 UI p-p.
Jitter Transfer
The jitter transfer function is the ratio of the jitter on the output
signal to the jitter applied on the input signal versus the fre-
quency. This parameter measures the limited amount of jitter
on an input signal that can be transferred to the output signal
(see Figure 7).
SLOPE = –20dB/DECADE
JITTER FREQUENCY – kHz
0.1
J
f
C
ACCEPTABLE
RANGE
Figure 7. Jitter Transfer Curve
Jitter Tolerance
The jitter tolerance is defined as the peak-to-peak amplitude of
the sinusoidal jitter applied on the input signal that causes a
1 dB power penalty. This is a stress test that is intended to
ensure no additional penalty is incurred under the operating
conditions (see Figure 8). Figure 9 shows the typical OC-48
jitter tolerance performance of the ADN2811.
SLOPE = –20dB/DECADE
f
0
f
1
JITTER FREQUENCY – Hz
f
2
f
3
f
4
15
1.5
0.15
I
Figure 8. SONET Jitter Tolerance Mask
MODULATION FREQUENCY – Hz
1.00E+01
1.00E+03
1.00E+05
1.00E+07
1.00E+02
1.00E+01
1.00E–01
A
1.00E+00
1.00E+02
1.00E+04
1.00E+06
1.00E+00
ADN2811
OC-48 SONET MASK
Figure 9. OC-48 Jitter Tolerance Curve
相關PDF資料 |
PDF描述 |
|---|---|
| ADN2811ACP-CML | OC-48/OC-48 FEC Clock and Data Recovery IC with Integrated Limiting Amp |
| ADN2811ACP-CML-RL | OC-48/OC-48 FEC Clock and Data Recovery IC with Integrated Limiting Amp |
| ADN2812 | Continuous Rate 12.3 Mb/s to 2.7 Gb/s Clock and Data Recovery IC with Integrated Limiting Amp |
| ADN2812ACP | Continuous Rate 12.3 Mb/s to 2.7 Gb/s Clock and Data Recovery IC with Integrated Limiting Amp |
| ADN2812ACP-RL | Continuous Rate 12.3 Mb/s to 2.7 Gb/s Clock and Data Recovery IC with Integrated Limiting Amp |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADN2811ACP-CML | 制造商:Analog Devices 功能描述:CDR 2488.32Mbps/2666.06Mbps SONET/SDH 48-Pin LFCSP EP Tray 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| ADN2811ACP-CML-RL | 制造商:Analog Devices 功能描述:CDR 2488.32Mbps/2666.06Mbps SONET/SDH 48-Pin LFCSP EP T/R |
| ADN2811ACPZ-CML | 功能描述:IC CLK/DATA REC W/AMP 48-LFCSP RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 專用 系列:- 標準包裝:28 系列:- 類型:時鐘/頻率發生器 PLL:是 主要目的:Intel CPU 服務器 輸入:時鐘 輸出:LVCMOS 電路數:1 比率 - 輸入:輸出:3:22 差分 - 輸入:輸出:無/是 頻率 - 最大:400MHz 電源電壓:3.135 V ~ 3.465 V 工作溫度:0°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:64-TFSOP （0.240"，6.10mm 寬） 供應商設備封裝:64-TSSOP 包裝:管件 |
| ADN2811ACPZ-CML-RL | 功能描述:IC CLK DATA REC SDH 2.66GHZ 制造商:analog devices inc. 系列:- 包裝:帶卷（TR） 零件狀態:上次購買時間 PLL:是 主要用途:SONET/SDH，STM 輸入:CML 輸出:CML 電路數:1 比率 - 輸入:輸出:1:2 差分 - 輸入:輸出:是/是 頻率 - 最大值:2.66GHz 電壓 - 電源:3 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-WFQFN 裸露焊盤 供應商器件封裝:48-LFCSP（7x7） 標準包裝:1 |
| ADN2812 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Continuous Rate 12.3 Mb/s to 2.7 Gb/s Clock and Data Recovery IC with Integrated Limiting Amp |
發布緊急采購，3分鐘左右您將得到回復。