- 您現在的位置：買賣IC網 > PDF目錄374016 > ADM8832ACPZ1 (Analog Devices, Inc.) Charge Pump Regulator for Color TFT Panel PDF資料下載
參數資料
| 型號： | ADM8832ACPZ1 |
| 廠商： | Analog Devices, Inc. |
| 英文描述： | Charge Pump Regulator for Color TFT Panel |
| 中文描述： | 電荷泵穩壓器的彩色液晶面板 |
| 文件頁數： | 10/12頁 |
| 文件大小： | 202K |
| 代理商： | ADM8832ACPZ1 |
ADM8832
THEORY OF OPERATION
SCANNING AND BLANKING
A TFT LCD panel is made up of a bank of capacitors, each
representing a pixel in the display. These capacitors store
different levels of charge, depending on the amount of
luminescence required for a given pixel. When a picture is
displayed on the panel, a scan of all the pixel capacitors is
performed, placing different levels of charge on each in order to
create the image. The process of updating the display like this is
called scanning. Once scanned, an image is held by pixel
capacitance, and the controller and source line drivers can be
put into a low power mode. This low power mode is referred to
as the blanking mode on the ADM8832. Over a finite period of
time, this pixel charge will leak and the capacitors will need to
be refreshed in order to maintain the image.
The ADM8832 uses scanning and blanking modes, as follows.
When the TFT LCD panel is in scanning mode, a logic high on
the SCAN/BLANK input places the device in high current
power mode, providing extra power (extra current) to the LCD
controller and the source line drivers. If the panel continues to
be updated (as when a moving picture is being displayed), the
ADM8832 can be continually operated in scanning mode. If the
same image is kept on the panel, a logic low is applied to the
SCAN/BLANK input, and the ADM8832 enters blanking (low
current) mode. Depending on how often the image is updated,
the ADM8832 can be operated with a variable SCAN/ BLANK
duty cycle. This helps to maximize power efficiency and,
therefore, extends the battery life.
POWER SEQUENCING
The gate drive supplies must be sequenced such that the 10 V
supply is up before the +15 V supply for the TFT panel to power
on correctly. The ADM8832 controls this sequence. When the
device is turned on (a logic high on SHDN), the ADM8832
allows the 10 V output to ramp immediately, but holds off the
+15 V output. It continues to do this until the negative output
reaches 3 V. At this point, the positive output is enabled and
allowed to ramp up to +15 V This sequence is shown in Figure 17.
Rev. A | Page 10 of 12
VCC
LOAD
SCAN/BLANK
EXTERNAL
CLOCK
SHDN
+5V
+15V
–10V
90%
10%
t
F10V
10%
90%
0
t
F15V
t
F5V
t
R5V
t
R15V
t
R15V
t
R10V
–3V
Figure 17. Power Sequence
TRANSIENT RESPONSE
The ADM8832 features extremely fast transient response,
making it very suitable for fast image updates on TFT LCD
panels. This means that even under changing load conditions
there is still very effective regulation of the 5 V output. Figure 12
and Figure 13 show how the 5.1 V output responds when a
maximum load is dynamically connected and disconnected.
Note that the output settles within 5 μs to less than 1% of the
output level.
EXTERNAL CLOCK
The ADM8832 has an internal 100 kHz oscillator, but an
external clock source can also be used to clock the part. This
clock source must be applied to the CLKIN pin. Power is saved
during blanking periods by disabling the internal oscillator and
by switching to the lower frequency external clock source. To
achieve optimum performance of the charge pump circuitry, it
is important that the duty cycle of the external clock source is
50% and that the rise and fall times are less than 20 ns.
90%
10%
t
R
: RISE TIME
t
F
: FALL TIME
t
H
t
T
@ 100% = DUTY CYCLE
0
t
R
t
F
t
H
t
T
Figure 18. Duty Cycle of External Clock
0.280
SOLDER MASK
BOARD METALLIZATION
0
0
0
0
0.400
0
0
1
2
0.250
0.200
0.875
Figure 19. Suggested LFCSP 4 mm × 4mm 20 Lead Land Pattern
相關PDF資料 |
PDF描述 |
|---|---|
| ADM8832ACP-REEL | Charge Pump Regulator for Color TFT Panel |
| ADM8832ACPZ-REEL | Charge Pump Regulator for Color TFT Panel |
| ADM8832ACPZ-REEL7 | Charge Pump Regulator for Color TFT Panel |
| ADM8839 | Charge Pump Regulator for Color TFT Panels |
| ADM8839ACP | Charge Pump Regulator for Color TFT Panels |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADM8832ACPZ-REEL | 功能描述:IC CHARGE PUMP REG TFT 20LFCSP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 標準包裝:43 系列:- 應用:控制器，Intel VR11 輸入電壓:5 V ~ 12 V 輸出數:1 輸出電壓:0.5 V ~ 1.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-VFQFN 裸露焊盤 供應商設備封裝:48-QFN（7x7） 包裝:管件 |
| ADM8832ACPZ-REEL7 | 功能描述:IC CHARGE PUMP REG TFT 20LFCSP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 標準包裝:43 系列:- 應用:控制器，Intel VR11 輸入電壓:5 V ~ 12 V 輸出數:1 輸出電壓:0.5 V ~ 1.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-VFQFN 裸露焊盤 供應商設備封裝:48-QFN（7x7） 包裝:管件 |
| ADM8832EB-EVALZ | 功能描述:BOARD EVALUATION ADM8832 REG RoHS:是 類別:編程器，開發系統 >> 評估板 - DC/DC 與 AC/DC（離線）SMPS 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:True Shutdown™ 主要目的:DC/DC，步升 輸出及類型:1，非隔離 功率 - 輸出:- 輸出電壓:- 電流 - 輸出:1A 輸入電壓:2.5 V ~ 5.5 V 穩壓器拓撲結構:升壓 頻率 - 開關:3MHz 板類型:完全填充 已供物品:板 已用 IC / 零件:MAX8969 |
| ADM8839 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Charge Pump Regulator for Color TFT Panels |
| ADM8839ACP | 制造商:Rochester Electronics LLC 功能描述: 制造商:Analog Devices 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。