參數資料
型號： ADM8690AN
廠商： ANALOG DEVICES INC
元件分類： 電源管理
英文描述： Microprocessor Supervisory Circuits
中文描述： 2-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDIP8
封裝： PLASTIC, MS-001, DIP-8
文件頁數： 11/16頁
文件大小： 183K
代理商： ADM8690AN
ADM8690–ADM8695
REV. 0
–11–
T Y PICAL APPLICAT IONS
ADM8690, ADM8692 and ADM8694
Figure 22a shows the ADM8690/ADM8692/ADM8694 in a
typical power monitoring, battery backup application. V
OUT
powers the CMOS RAM. Under normal operating conditions
with V
CC
present, V
OUT
is internally connected to V
CC
. If a
power failure occurs, V
CC
will decay and V
OUT
will be switched
to V
BAT T
thereby maintaining power for the CMOS RAM. A
RESET
pulse is also generated when V
CC
falls below 4.65 V for
the ADM8690/ADM8694 or 4.4 V for the ADM8692.
RESET
will remain low for 50 ms (200 ms for ADM8694) after V
CC
re-
turns to 5 V.
T he watchdog timer input (WDI) monitors an I/O line from the
μ
P system. T his line must be toggled once every 1.6 seconds to
verify correct software execution. Failure to toggle the line indi-
cates that the
μ
P system is not correctly executing its program
and may be tied up in an endless loop. If this happens, a reset
pulse is generated to initialize the processor.
If the watchdog timer is not needed, the WDI input should be
left floating.
T he Power Fail Input, PFI, monitors the input power supply via
a resistive divider network. T he voltage on the PFI input is com-
pared with a precision 1.3 V internal reference. If the input volt-
age drops below 1.3 V, a power fail output (
PFO
) signal is
generated. T his warns of an impending power failure and may
be used to interrupt the processor so that the system may be
shut down in an orderly fashion. T he resistors in the sensing
network are ratioed to give the desired power fail threshold
voltage V
T
.
V
T
=
(1.3
R
1/
R
2)
+
1.3
V
R
1/
R
2 = (
V
T
/1.3) – 1
+
BATTERY
R
1
R
2
+5V
0.1μF
ADM8690
ADM8692
ADM8694
V
CC
PFI
V
BATT
V
OUT
WDI
PFO
RESET
GND
μP POWER
CMOS RAM
POWER
μP SYSTEM
μP
RESET
μP NMI
I/O LINE
Figure 22a. ADM8690/ADM8692/ADM8694 Typical Applica-
tion Circuit A
Figure 22b shows a similar application but in this case the PFI
input monitors the unregulated input to the 7805 voltage regu-
lator. T his gives an earlier warning of an impending power fail-
ure. It is useful with processors operating at low speeds or where
there are a significant number of housekeeping tasks to be com-
pleted before the power is lost.
+
BATTERY
R
1
R
2
INPUT
POWER
V > 8V
0.1μF
0.1μF
7805
+5V
μP POWER
CMOS RAM
POWER
μP SYSTEM
μP
RESET
μP NMI
I/O LINE
ADM8690
ADM8692
ADM8694
V
CC
PFI
V
BATT
V
OUT
WDI
PFO
RESET
GND
Figure 22b. ADM8690/ADM8692/ADM8694 Typical Applica-
tion Circuit B
ADM8691, ADM8693 and ADM8695
A typical connection for the ADM8691/ADM8693/ADM8695
is shown in Figure 23. CMOS RAM is powered from V
OUT
.
When 5 V power is present this is routed to V
OUT
. If V
CC
fails
then V
BAT T
is routed to V
OUT
. V
OUT
can supply up to 100 mA
from V
CC
, but if more current is required, an external PNP tran-
sistor can be added. When V
CC
is higher than V
BAT T
, the BAT T
ON output goes low, providing up to 25 mA of base drive for
the external transistor. A 0.1
μ
F capacitor is connected to V
OUT
to supply the transient currents for CMOS RAM. When V
CC
is
lower than V
BAT T
, an internal 20
MOSFET connects the
backup battery to V
OUT
.
3V
BATTERY
R
1
R
2
0.1μF
0.1μF
0.1μF
RESET
SYSTEM STATUS
INDICATORS
NC
INPUT POWER
+5V
A0–A15
I/O LINE
NMI
RESET
μP
ADM8691
ADM8693
ADM8695
BATT
ON
V
CC
V
OUT
V
BATT
CE
OUT
CE
IN
PFI
GND
OSC IN
OSC SEL
WDI
PFO
RESET
LOW LINE
WDO
ADDRESS
DECODE
CMOS
RAM
Figure 23. ADM8691/ADM8693/ADM8695 Typical
Application
相關PDF資料
PDF描述
ADM8690ARN Microprocessor Supervisory Circuits
ADM8692 Linear 1-cell Li-Ion Battery Charger w/Integrated FET, One LED 20-VQFN -40 to 70
ADM8692AN Linear 1-cell Li-Ion Battery Charger W/Integrated FET, Bi-Color LED 20-HTSSOP -20 to 70
ADM8692ARN Linear 1-cell Li-Ion Battery Charger W/Integrated FET, Bi-Color LED 20-HTSSOP -20 to 70
ADM8694 bqTINY(TM) Linear 1-cell Li-Ion Charger w/ 1-A FET, Charge Enable & Term Enable in QFN-10 10-SON -40 to 85
相關代理商/技術參數
參數描述
ADM8690ANZ 功能描述:IC SUPERVISOR MPU 4.65V 8DIP RoHS:是 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 標準包裝:1 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:開路漏極或開路集電極 復位:高有效 復位超時:- 電壓 - 閥值:1.8V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:6-TSOP（0.059"，1.50mm 寬）5 引線 供應商設備封裝:5-TSOP 包裝:剪切帶 (CT) 其它名稱:NCP301HSN18T1GOSCT
ADM8690ARN 功能描述:IC SUPERVISOR MPU 4.65V 8SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 標準包裝:1 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:開路漏極或開路集電極 復位:高有效 復位超時:- 電壓 - 閥值:1.8V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:6-TSOP（0.059"，1.50mm 寬）5 引線 供應商設備封裝:5-TSOP 包裝:剪切帶 (CT) 其它名稱:NCP301HSN18T1GOSCT
ADM8690ARN-REEL 功能描述:IC SUPERVISOR MPU 4.65V 8SOIC TR RoHS:否 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 標準包裝:1 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:開路漏極或開路集電極 復位:高有效 復位超時:- 電壓 - 閥值:1.8V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:6-TSOP（0.059"，1.50mm 寬）5 引線 供應商設備封裝:5-TSOP 包裝:剪切帶 (CT) 其它名稱:NCP301HSN18T1GOSCT
ADM8690ARNZ 功能描述:IC SUPERVISOR MPU 4.65V 8SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 其它有關文件:STM6717 View All Specifications 標準包裝:1 系列:- 類型:多壓監控器 監視電壓數目:2 輸出:開路漏極或開路集電極 復位:低有效 復位超時:最小為 600 ms 電壓 - 閥值:1.11V，3.075V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SC-74A，SOT-753 供應商設備封裝:SOT-23-5 包裝:Digi-Reel® 產品目錄頁面:1194 (CN2011-ZH PDF) 其它名稱:497-7019-6
ADM8691 制造商:AD 制造商全稱:Analog Devices 功能描述:Microprocessor Supervisory Circuits
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*