參數資料
型號: ADM489ANZ
廠商: Analog Devices Inc
文件頁數: 6/16頁
文件大?。?/td> 0K
描述: IC TXRX RS485 LO SLEW/EN 14DIP
標準包裝: 25
類型: 收發器
驅動器/接收器數: 1/1
規程: RS422,RS485
電源電壓: 4.5 V ~ 5.5 V
安裝類型: 通孔
封裝/外殼: 14-DIP(0.300",7.62mm)
供應商設備封裝: 14-PDIP
包裝: 管件
產品目錄頁面: 790 (CN2011-ZH PDF)
ADM488/ADM489
Rev. D | Page 14 of 16
APPLICATION INFORMATION
DIFFERENTIAL DATA TRANSMISSION
Differential data transmission is used to reliably transmit data at
high rates over long distances and through noisy environments.
Differential transmission nullifies the effects of ground shifts
and noise signals, which appear as common-mode voltages on
the line. Two main standards that specify the electrical
characteristics of transceivers used in differential data
transmission are approved by the EIA.
The RS-422 standard specifies data rates up to 10 MBaud and
line lengths up to 4000 ft. A single driver can drive a transmis-
sion line with up to 10 receivers.
To cater to true multipoint communications, the RS-485 stan-
dard was defined to meet or exceed the requirements of RS-422.
It also allows up to 32 drivers and 32 receivers to be connected
to a single bus. An extended common-mode range of 7 V to
+12 V is defined. The most significant difference between the
RS-422 and RS-485 is that the RS-485 drivers can be disabled,
thereby allowing up to 32 receivers to be connected to a single
line. Only one driver should be enabled at a time, but the RS-
485 standard contains additional specifications to guarantee
device safety in the event of line contention.
CABLE AND DATA RATE
The transmission line of choice for RS-485 communications is a
twisted pair. Twisted-pair cable tends to cancel common-mode
noise and also causes cancellation of the magnetic fields gener-
ated by the current flowing through each wire, thereby reducing
the effective inductance of the pair.
The ADM488/ADM489 are designed for bidirectional data
communications on multipoint transmission lines. A typical
application showing a multipoint transmission network is
illustrated in Figure 30. An RS-485 transmission line can have
up to 32 transceivers on the bus. Only one driver can transmit
at a particular time, but multiple receivers can be simultane-
ously enabled.
As with any transmission line, it is important that reflections be
minimized. This can be achieved by terminating the extreme
ends of the line using resistors equal to the characteristic im-
pedance of the line. Stub lengths of the main line should also be
kept as short as possible. A properly terminated transmission
line appears purely resistive to the driver.
Table 10. Comparison of RS-422 and RS-485 Interface Standards
Specification
RS-422
RS-485
Transmission Type
Differential
Maximum Data Rate
10 MB/s
Maximum Cable Length
4000 ft.
Minimum Driver Output Voltage
±2 V
±1.5 V
Driver Load Impedance
100 Ω
54 Ω
Receiver Input Resistance
4 kΩ minimum
12 kΩ minimum
Receiver Input Sensitivity
±200 mV
Receiver Input Voltage Range
7 V to +7 V
7 V to +12 V
Number of Drivers/Receivers per Line
1/10
32/32
D
R
D
R
D
R
RT
D
R
00
079
-03
0
Figure 30. Typical RS-485 Network
相關PDF資料
PDF描述
206060-1 CONN PLUG CPC 4POS STD SER 1
ADM489ARUZ IC TXRX RS-485 DIFF LP 16TSSOP
206043-1 CONN RECEPT CPC 14POS REV SER 1
ADM211ARSZ IC TX/RX RS-232 5V 0.1UF 28SSOP
206430-3 CONN RECEPT CPC 4POS REV SER 1
相關代理商/技術參數
參數描述
ADM489AR 制造商:Analog Devices 功能描述:Single Transmitter/Receiver RS-422/RS-485 14-Pin SOIC N 制造商:Analog Devices 功能描述:IC TRANSCEIVER RS485
ADM489AR-REEL 制造商:Analog Devices 功能描述:Single Transmitter/Receiver RS-422/RS-485 14-Pin SOIC N T/R 制造商:Rochester Electronics LLC 功能描述:FULL DUPLEX,RS-485 TRANSCEIVER I.C. - Tape and Reel
ADM489AR-REEL7 制造商:Analog Devices 功能描述:Single Transmitter/Receiver RS-422/RS-485 14-Pin SOIC N T/R
ADM489ARU 制造商:Rochester Electronics LLC 功能描述:FULL DUPLEX,RS-485 TRANSCEIVER I.C. - Bulk
ADM489ARU-REEL 制造商:Analog Devices 功能描述:Single Transmitter/Receiver RS-422/RS-485 16-Pin TSSOP T/R 制造商:Analog Devices 功能描述:LINE TRNSCVR 1TR 1TX 1RX 16TSSOP - Tape and Reel