- 您現在的位置：買賣IC網 > PDF目錄374003 > ADM483 (Analog Devices, Inc.) 5 V Low Power, Slew-Rate Limited RS-485/RS-422 Transceiver PDF資料下載
參數資料
| 型號： | ADM483 |
| 廠商： | Analog Devices, Inc. |
| 英文描述： | 5 V Low Power, Slew-Rate Limited RS-485/RS-422 Transceiver |
| 中文描述： | 5 V低功耗，擺率限制RS-485/RS-422收發器 |
| 文件頁數： | 11/16頁 |
| 文件大?。?/td> | 209K |
| 代理商： | ADM483 |
ADM483
APPLICATIONS
DIFFERENTIAL DATA TRANSMISSION
Differential data transmission is used to reliably transmit
data at high rates over long distances and through noisy
environments. Differential transmission nullifies the effects
of ground shifts and noise signals that appear as common-
mode voltages on the line. There are two main standards
approved by the Electronics Industries Association (EIA),
which specify the electrical characteristics of transceivers
used in differential data transmission.
Rev. 0 | Page 11 of 16
The RS-422 standard specifies data rates up to 10 Mbaud
and line lengths up to 4000 ft. A single driver can drive a
transmission line with up to 10 receivers.
To achieve true multipoint communications, the RS-485
standard was defined. This standard meets or exceeds all the
requirements of RS-422, but also allows up to 32 drivers and 32
receivers to be connected to a single bus. An extended common-
mode range of –7 V to +12 V is defined. The most significant
difference between RS-422 and RS-485 is that the drivers may
be disabled, allowing up to 32 to be connected to a single line.
Only one driver should be enabled at a time, but the RS-485
standard contains additional specifications to guarantee device
safety in the event of line contention.
Table 5. Comparison of RS-422 and RS-485 Interface Standards
Specification
Transmission Type
Maximum Cable Length
Minimum Driver Output Voltage
Driver Load Impedance
Receiver Input Resistance
Receiver Input Sensitivity
Receiver Input Voltage Range
Drivers/Receivers per Line
CABLE AND DATA RATE
The preferred transmission line for RS-485 communications
is a twisted pair. Twisted pair cable tends to cancel common-
mode noise and the magnetic fields generated by the current
flowing through each wire, thereby reducing the effective
inductance of the pair.
RS-422
Differential
4000 ft.
±2 V
100
4 k min
±200 mV
–7 V to +7 V
1/10
RS-485
Differential
4000 ft.
±1.5 V
54
12 k min
±200 mV
–7 V to +12 V
32/32
The ADM483 is designed for bidirectional data communica-
tions on multipoint transmission lines. A typical application
showing a multipoint transmission network is shown in
Figure 24
. An RS-485 transmission line can have as many as
32 transceivers on the bus. Only one driver can transmit at a
particular time, but multiple receivers can be enabled simul-
taneously. As with any transmission line, it is important to
minimize reflections. This can be done by terminating the
extreme ends of the line by using resistors equal to the char-
acteristic impedance of the line. Stub lengths of the main
line should also be kept as short as possible. A properly
terminated transmission line appears purely resistive to
the driver.
0
RO
RE
DE
DI
D
R
A
B
MAXIMUM NUMBER OF TRANSCEIVERS ON BUS: 32
ADM483
RO
RE
DE
DI
D
R
A
B
ADM483
R
ADM483
D
RO
RE DE
DI
A
B
R
ADM483
D
RO
RE DE
DI
A
B
Figure 24. Typical Half-Duplex RS-485 Network Topology
相關PDF資料 |
PDF描述 |
|---|---|
| ADM483AR | 5 V Low Power, Slew-Rate Limited RS-485/RS-422 Transceiver |
| ADM483AR-REEL | 5 V Low Power, Slew-Rate Limited RS-485/RS-422 Transceiver |
| ADM483AR-REEL7 | 5 V Low Power, Slew-Rate Limited RS-485/RS-422 Transceiver |
| ADM483JR | 5 V Low Power, Slew-Rate Limited RS-485/RS-422 Transceiver |
| ADM4852 | 5 V Slew-Rate Limited Half- and Full-Duplex RS-485/RS-422 Transceivers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADM483AR | 制造商:Analog Devices 功能描述:Single Transmitter/Receiver RS-422/RS-485 8-Pin SOIC N |
| ADM483AR-REEL | 制造商:AD 制造商全稱:Analog Devices 功能描述:5 V Low Power, Slew-Rate Limited RS-485/RS-422 Transceiver |
| ADM483AR-REEL7 | 制造商:AD 制造商全稱:Analog Devices 功能描述:5 V Low Power, Slew-Rate Limited RS-485/RS-422 Transceiver |
| ADM483ARZ | 功能描述:IC TXRX RS485/RS422 LP 8SOIC RoHS:是 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:1 系列:- 類型:線路收發器 驅動器/接收器數:5/3 規程:RS232 電源電壓:3 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC 包裝:Digi-Reel® 產品目錄頁面:918 (CN2011-ZH PDF) 其它名稱:296-25096-6 |
| ADM483E | 制造商:AD 制造商全稱:Analog Devices 功能描述:+-15 kV ESD Protected, EMC Compliant Slew Rate Limited, EIA RS-485 Transceiver |
發布緊急采購，3分鐘左右您將得到回復。