參數資料
型號： ADM1034ARQZ-REEL
廠商： ON Semiconductor
文件頁數： 29/38頁
文件大?。?/td> 427K
描述： IC THERM/FAN SPEED CTRLR 16-QSOP
產品變化通告： MFG CHG Notification ADI to ON Semi
標準包裝： 2,500
功能： 風扇控制，溫度監控器
傳感器類型： 內部和外部
感應溫度： -40°C ~ 125°C，外部傳感器
精確度： ±1°C
拓?fù)洌?/td> ADC，比較器，多路復用器，寄存器庫
輸出類型： SMBus?
輸出警報： 是
輸出風扇： 是
電源電壓： 3 V ~ 5.5 V
工作溫度： -40°C ~ 125°C
安裝類型： 表面貼裝
封裝/外殼： 16-SSOP（0.154"，3.90mm 寬）
供應商設備封裝： 16-QSOP
包裝： 帶卷 (TR)
ADM1034
http://onsemi.com
29
Table 36. REGISTER 0X00, # BYTES/BLOCK READ, POR = 0X20, LOCK = Y, S/W RESET = Y
Bit
Name
R/W
Description
<7:0>
# Bytes Block Read
R/W
Block reads are # bytes/block read long. The maximum is 32 bytes, the SMBus
transaction limit.
Table 37. REGISTER 0X01, CONFIGURATION REGISTER 1, POWER-ON DEFAULT 0X01, LOCK = Y, S/W RESET = Y
Bit
Name
R/W
Description
7
Table/SW Con
R/W
Set this bit to 1 to place the fan speed under the control of the look-up table. When this
bit is 0, the ADM1034 is in software/manual control mode. Default = 0.
6
Lock Bit
R/W
Set this bit to 1 to prevent the user from writing to the ADM1034 registers.
1 = ADM1034 registers locked. 0 = ADM1034 registers unlocked. Default = 0.
5
SDA Timeout
R/W
1 = SDA timeout enabled. 0 = SDA timeout disabled. Default = 0.
4
SCL Timeout
R/W
1 = SCL timeout enabled. 0 = SDL timeout disabled. Default = 0.
3
ALERT
 Configuration
R/W
0 = SMBusALERT
. Default = 0. 1 = ALERT
_COMP mode.
2
Enable THERM
 Timer
R/W
1 = timer enabled, 0 = timer disabled. This bit enables THERM
 as an input. Default = 0.
1
Averaging Off
R/W
This bit is used to disable averaging at the slower conversion rates (8 Hz and slower).
Averaging is automatically disabled at the higher (16, 32, and 64 Hz ) conversion rates.
Default = averaging on = 0.
0
Monitor/STBY
R/W
Set bit to 1 to enable temperature monitoring. Set bit to 0 to disable it.
Power-On Default = 1.
Table 38. REGISTER 0X02, CONFIGURATION REGISTER 2, POWER-ON DEFAULT 0X84, LOCK = Y, S/W RESET = Y
Bit
Name
R/W
Description
7
Round Robin
R/W
This bit enables the round-robin mode. Set this bit to 0 to put the ADM1034 in
single-channel mode. The ADC converts on one channel only, which is determined by
the channel selector bits. Default = Round Robin = 1.
6
Reserved
R/W
Reserved
<5:4>
Channel Selector
R/W
This bit determines the channel on which the ADC converts.
00 = Local Channel Only
01 = Remote 1 Channel Only
10 = Remote 2 Channel Only
11 = Reserved
3
4:8 Look-up Table
R/W
This bit determines how many table points are used to control each fan.
0 = 4 table points for each fan.
1 = all 8 points on one table; this table is used to control both fans.
2
Discrete/Linear Speed
R/W
This bit determines whether the fans run at discrete speeds or at speeds that increase
with temperature between the two thresholds. Default = 1 = Linear.
1
Boost Disable
R/W
Set bit to 1 to prevent the fans from being boosted if either THERM
 temperature or
THERM
 timer limits are exceeded. Under these conditions, the fan runs at the
previously calculated speed. Default = 0.
0
SW Reset
R/W
Set this bit to 1 to reset the ADM1034 registers to their default values, excluding the limit
registers, offset registers, and look-up table registers. This bit self-clears. Default = 0.
Table 39. REGISTER 0X03, CONFIGURATION REGISTER 3, POWER-ON DEFAULT 0X44, LOCK = Y, S/W RESET = Y
Bit
Name
R/W
Description
<7:4>
#Poles Fan 2
R/W
Write the number of poles on Fan 2 to this register. power-on default = 4 poles = 100.
This should always be an even number, because there cannot be an odd number of
poles in a fan.
<3:0>
#Poles Fan 1 1
R/W
Write the number of poles in Fan 1 to this register. power-on default = 4 poles = 00.
This should always be an even number, because there cannot be an odd number of
poles in a fan.
相關PDF資料
PDF描述
ADN8810ACPZ-REEL7 IC CURRENT SOURCE(12BIT) 24LFCSP
ADP2140ACPZ3328R7 IC REG DL BCK/LINEAR 10LFCSP
ADP5022ACBZ-6-R7 IC REG TRPL BCK/LINEAR 16WLCSP
ADP5041ACPZ-1-R7 IC REG TRPL BCK/LINEAR 20-LFCSP
ADP5042ACPZ-2-R7 IC REG TRPL BCK/LINEAR 20LFCSP
相關代理商/技術參數
參數描述
ADM1034ARQZ-REEL7 功能描述:IC THERM/FAN SPEED CTRLR 16-QSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:1 系列:- 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C，外部傳感器 精確度:±2.5°C 本地（最大值），±5°C 遠程（最大值） 拓?fù)?ADC，比較器，寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6
ADM1040 制造商:AD 制造商全稱:Analog Devices 功能描述:Power Supply Monitor ASIC
ADM1041 制造商:AD 制造商全稱:Analog Devices 功能描述:Secondary-Side Controller with Current Share and Housekeeping
ADM1041A 制造商:AD 制造商全稱:Analog Devices 功能描述:Secondary-Side Controller with Current Share and Housekeeping
ADM1041AARQZ 功能描述:IC SECONDARY SIDE CTRLR 24QSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 電源控制器，監視器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 應用:多相控制器 輸入電壓:- 電源電壓:9 V ~ 14 V 電流 - 電源:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:40-WFQFN 裸露焊盤 供應商設備封裝:40-TQFN-EP（5x5） 包裝:帶卷 (TR)
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*