- 您現在的位置：買賣IC網 > PDF目錄373995 > ADM1022ARQ (ANALOG DEVICES INC) Low-Cost PC Temperature Monitor and Fan Control ASIC PDF資料下載
參數資料
| 型號： | ADM1022ARQ |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 電源管理 |
| 英文描述： | Low-Cost PC Temperature Monitor and Fan Control ASIC |
| 中文描述： | 2-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO16 |
| 封裝： | MO-137AB, QSOP-16 |
| 文件頁數： | 14/19頁 |
| 文件大?。?/td> | 190K |
| 代理商： | ADM1022ARQ |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁第18頁第19頁
REV. 0
ADM1022
–14–
GENERAL PURPOSE LOGIC INPUT (GPI)
Pin 12 may be configured as an input for a second temperature
sensor input by setting Bit 7 of the Configuration Register, or it
may be used as a general purpose logic input by clearing Bit 7 of
the Configuration Register, which is its default condition. The
GPI input may be programmed to be active high or active low by
clearing or setting Bit 6 of the Configuration Register. The default
value is active high. Bit 4 of the Interrupt Status Register follows
the state (or inverted state) of GPI and will generate an interrupt
when it is set to one, like any other input to the Interrupt Status
Register. However, the GPI bit is not latched in the Status Register
and always reflects the current state (or inverted state) of the
GPI input. If it is one it will not be cleared by reading the
Status Register.
RESETS
The ADM1022 has a manual reset input, (Pin 2 –
MR
), a bidi-
rectional reset pin, (Pin 3 –
RST1
) and a reset output (Pin 7 –
RST2
). These operate as follows:
Taking
MR
low forces a system reset and takes the
RST2
output
low. It will remain low for t
RP
after
MR
goes high again. The
MR
input has a 20 k
pull-up resistor, and may be left uncon-
nected if not used.
MR
is typically used to generate a system
reset from a front-panel push-button.
The
RST1
pin is a bidirectional I/O. It is asserted low as an out-
put if V
CC
falls below the reset threshold. It can also operate as a
reset input to the ADM1022 in the same way as
MR
. At power-
up,
RST2
will remain asserted for t
RP
after
RST1
goes high.
The
RST2
output is asserted low under any of the following
conditions:
≤
the
MR
input is low, as previously described,
–
RST1
is asserted low as an output or pulled low as an input,
≤
V
MON
is below the reset threshold.
POWER-ON RESET
When the ADM1022 is powered up, it will initiate a power-on
reset sequence when the supply voltage V
CC
rises above the
power-on reset threshold, with registers being reset to their
power-on values. Normal operation will begin when the supply
voltage rises above the reset threshold. Registers whose power-
on values are not shown have power on conditions that are
indeterminate (this includes the Value and Limit Registers). In
most applications, usually the first action after power-on would
be to write limits into the Limit Registers.
Power-on reset clears or initializes the following registers (the ini-
tialized values are shown in Table IV):
– Configuration Register
– Interrupt Status Register
– Interrupt Status Mirror Register
– Interrupt Mask Register
– Test Register
– Analog Output Register
– Programmable Trip Point Registers
Operation of the reset outputs at power-up, and for a manual
reset input, is shown in Figure 18. It should be noted that the
resets will only be asserted once V
CC
rises above 1 V. Below this
voltage there is insufficient gate drive voltage to turn on the out-
put FETs. If the device being reset and its pull-up resistor is
supplied from V
CC
, the reset voltage will rise with V
CC
to 1 V
before being pulled low. If the device being reset and its pull-up
resistor use a separate supply voltage, the reset output will fol-
low that voltage until reset is asserted.
The ADM1022 can also be reset by taking
RST1
low as an input.
The above-mentioned registers will be reset to their default
values and the ADC will remain inactive as long as
RST1
is
below the reset threshold.
V
CC
–
1V
t
RP
t
t
RP
t
RP
RST1
RST2
MR
RST2
POWER-ON RESET
MANUAL RESET (FOR EXAMPLE)
Figure 18. Operation of Reset Outputs
RST1
AS I/O
If
RST1
is used as a reset input to the ADM1022 while also
being used as a system reset output, it will be necessary to sepa-
rate the two functions so that a reset from the system to the
ADM1022 does not also reset the system.
This can be achieved using the circuit of Figure 19. If
ALT_RST
is high, then reset outputs from the ADM1022 can pass through
N2 to reset the system.
If, however,
ALT_RST
is low, the ADM1022 will be reset, but
SYS_RST
will be held high by the high input from N1 to N2.
ADM1022
RST1
100k
N1
V
CC
N2
SYS_RST
ALT_RST
Figure 19. Separation of
RST1
Input from
RST1
Output
相關PDF資料 |
PDF描述 |
|---|---|
| ADM1023 | LJT 6C 6#12 PIN PLUG |
| ADM1023ARQ | ACPI-Compliant High-Accuracy Microprocessor System Temperature Monitor |
| ADM1024 | System Hardware Monitor with Remote Diode Thermal Sensing |
| ADM1024ARU | Circular Connector; No. of Contacts:8; Series:LJT06R; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:17; Circular Contact Gender:Pin; Circular Shell Style:Straight Plug; Insert Arrangement:17-8 |
| ADM1025 | Circular Connector; No. of Contacts:8; Series:LJT06R; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:17; Circular Contact Gender:Pin; Circular Shell Style:Straight Plug; Insert Arrangement:17-8 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADM1022ARQ-REEL | 功能描述:IC SENSOR TEMP/DET 3/5.5V 16QSOP RoHS:否 類別:集成電路 (IC) >> 接口 - 傳感器和探測器接口 系列:- 其它有關文件:Automotive Product Guide 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:74 系列:- 類型:觸控式傳感器 輸入類型:數字 輸出類型:數字 接口:JTAG，串行 電流 - 電源:100µA 安裝類型:表面貼裝 封裝/外殼:20-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:20-TSSOP 包裝:管件 |
| ADM1022ARQ-REEL7 | 功能描述:IC SENSOR TEMP/DET 3/5.5V 16QSOP RoHS:否 類別:集成電路 (IC) >> 接口 - 傳感器和探測器接口 系列:- 其它有關文件:Automotive Product Guide 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:74 系列:- 類型:觸控式傳感器 輸入類型:數字 輸出類型:數字 接口:JTAG，串行 電流 - 電源:100µA 安裝類型:表面貼裝 封裝/外殼:20-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:20-TSSOP 包裝:管件 |
| ADM1022ARQZ | 功能描述:IC SENSOR TEMP/DET 3/5.5V 16QSOP RoHS:是 類別:集成電路 (IC) >> 接口 - 傳感器和探測器接口 系列:- 其它有關文件:Automotive Product Guide 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:74 系列:- 類型:觸控式傳感器 輸入類型:數字 輸出類型:數字 接口:JTAG，串行 電流 - 電源:100µA 安裝類型:表面貼裝 封裝/外殼:20-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:20-TSSOP 包裝:管件 |
| ADM1022ARQZ-R7 | 功能描述:IC SENSOR TEMP/DET 3/5.5V 16QSOP RoHS:是 類別:集成電路 (IC) >> 接口 - 傳感器和探測器接口 系列:- 其它有關文件:Automotive Product Guide 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:74 系列:- 類型:觸控式傳感器 輸入類型:數字 輸出類型:數字 接口:JTAG，串行 電流 - 電源:100µA 安裝類型:表面貼裝 封裝/外殼:20-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:20-TSSOP 包裝:管件 |
| ADM1022ARQZ-REEL | 功能描述:IC SENSOR TEMP/DET 3/5.5V 16QSOP RoHS:是 類別:集成電路 (IC) >> 接口 - 傳感器和探測器接口 系列:- 其它有關文件:Automotive Product Guide 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:74 系列:- 類型:觸控式傳感器 輸入類型:數字 輸出類型:數字 接口:JTAG，串行 電流 - 電源:100µA 安裝類型:表面貼裝 封裝/外殼:20-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:20-TSSOP 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。