- 您現在的位置：買賣IC網 > PDF目錄375254 > ADE7761AARSZ-RL (ANALOG DEVICES INC) Energy Metering IC with On-Chip Fault and Missing Neutral Detection PDF資料下載
參數資料
| 型號： | ADE7761AARSZ-RL |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 模擬信號調理 |
| 英文描述： | Energy Metering IC with On-Chip Fault and Missing Neutral Detection |
| 中文描述： | SPECIALTY ANALOG CIRCUIT, PDSO20 |
| 封裝： | LEAD FREE, M0-150AE, SSOP-20 |
| 文件頁數： | 6/24頁 |
| 文件大?。?/td> | 367K |
| 代理商： | ADE7761AARSZ-RL |
ADE7761A
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
Rev. 0 | Page 6 of 24
REF
IN/OUT
S0
S1
SCF
V
DD
V
1A
V
1B
V
1N
V
2N
V
2P
F1
F2
CF
DGND
REVP
FAULT
RCLKIN
PGA
MISCAL
AGND
1
2
3
4
20
19
18
17
5
6
7
16
15
14
8
13
9
12
10
11
ADE7761A
TOP VIEW
(Not to Scale)
0
Figure 3. Pin Configuration (SSOP)
Table 4. Pin Function Descriptions
Pin No.
Mnemonic
1
V
DD
Description
Power Supply. This pin provides the supply voltage for the digital circuitry in the ADE7761A. The supply voltage
should be maintained at 5 V ± 5% for specified operation. This pin should be decoupled with a 10 μF capacitor
in parallel with a ceramic 100 nF capacitor.
Analog Inputs for Channel 1 (Current Channel). These inputs are fully differential voltage inputs with maximum
differential input signal levels of ±660 mV with respect to V
1N
for specified operation. The maximum signal level
at these pins is ±1 V with respect to AGND. Both inputs have internal ESD protection circuitry, and an overvoltage
of ±6 V can also be sustained on these inputs without risk of permanent damage.
Negative Input for Differential Voltage Inputs, V
1A
and V
1B
. The maximum signal level at this pin is ±1 V with
respect to AGND. The input has internal ESD protection circuitry, and an overvoltage of ±6 V can also be sustained
on this input without risk of permanent damage. The input should be directly connected to the burden resistor
and held at a fixed potential, that is, AGND. See the Analog Inputs section.
Negative Input for Differential Voltage Inputs, V
2P
and MISCAL. The maximum signal level at this pin is ±1 V with
respect to AGND. The input has internal ESD protection circuitry, and an overvoltage of ±6 V can also be sustained
on this input without risk of permanent damage. The input should be held at a fixed potential, that is, AGND. See
the Analog Inputs section.
Analog Input for Channel 2 (Voltage Channel). This input is a fully differential voltage input with maximum
differential input signal levels of ±660 mV with respect to V
2N
for specified operation. The maximum signal level at
this pin is ±1 V with respect to AGND. This input has internal ESD protection circuitry, and an overvoltage of ±6 V
can also be sustained on this input without risk of permanent damage.
Analog Input for Missing Neutral Calibration. This pin can be used to calibrate the CF-F1-F2 frequencies in the
missing neutral condition. This input is a fully differential voltage input with maximum differential input signal
levels of 660 mV with respect to V
2N
for specified operation. The maximum signal level at this pin is ±1 V with
respect to AGND. This input has internal ESD protection circuitry, and an overvoltage of ±6 V can also be
sustained on this input without risk of permanent damage.
This pin provides the ground reference for the analog circuitry in the ADE7761A, that is, ADCs and reference. This
pin should be tied to the analog ground plane of the PCB. The analog ground plane is the ground reference for all
analog circuitry, such as antialiasing filters, and current and voltage transducers. For good noise suppression, the
analog ground plane should be connected only to the digital ground plane at the DGND pin.
This pin provides access to the on-chip voltage reference. The on-chip reference has a nominal value of
2.5 V ± 8% and a typical temperature coefficient of 30 ppm/°C. An external reference source can also be
connected at this pin. In either case, this pin should be decoupled to AGND with a 1 μF ceramic capacitor and
100 nF ceramic capacitor.
Select Calibration Frequency. This logic input is used to select the frequency on the calibration output CF.
Table 7 shows how the calibration frequencies are selected.
These logic inputs are used to select one of four possible frequencies for the digital-to-frequency conversion.
This offers the designer greater flexibility when designing the energy meter. See the Selecting a Frequency for an
Energy Meter Application section.
This logic input is used to select the gain for the analog inputs, V
1A
and V
1B
. The possible gains are 1 and 16.
To enable the internal oscillator as a clock source on the chip, a precise low temperature drift resistor at
nominal value of 6.2 kΩ must be connected from this pin to DGND.
2, 3
V
1A
, V
1B
4
V
1N
5
V
2N
6
V
2P
7
MISCAL
8
AGND
9
REF
IN/OUT
10
SCF
11, 12
S1, S0
13
14
PGA
RCLKIN
相關PDF資料 |
PDF描述 |
|---|---|
| ADE7761 | Energy Metering IC with On-Chip Fault and Missing Neutral Detection |
| ADE7761ARS | Energy Metering IC with On-Chip Fault and Missing Neutral Detection |
| ADE7761ARS-REF | Energy Metering IC with On-Chip Fault and Missing Neutral Detection |
| ADE7761ARSRL | Energy Metering IC with On-Chip Fault and Missing Neutral Detection |
| ADE7769 | Energy Metering IC with Integrated Oscillator and No-Load Indication |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADE7761ARS | 制造商:Rochester Electronics LLC 功能描述: 制造商:Analog Devices 功能描述: |
| ADE7761ARS-REF | 制造商:Analog Devices 功能描述:ENERGY METER IC W/FAULT&MNEUT DETEC. - Bulk |
| ADE7761ARSRL | 制造商:AD 制造商全稱:Analog Devices 功能描述:Energy Metering IC with On-Chip Fault and Missing Neutral Detection |
| ADE7761B | 制造商:AD 制造商全稱:Analog Devices 功能描述:Energy Metering IC with On-Chip Fault and Missing Neutral Detection |
| ADE7761BARS | 制造商:Rochester Electronics LLC 功能描述: 制造商:Analog Devices 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。