- 您現在的位置：買賣IC網 > PDF目錄373980 > ADE7759ARS (ANALOG DEVICES INC) 8-Channel 14-Bit Single-Supply Voltage-Output DAC; Package: LQFP (10x10mm); No of Pins: 52; Temperature Range: Industrial PDF資料下載
參數資料
| 型號： | ADE7759ARS |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 模擬信號調理 |
| 英文描述： | 8-Channel 14-Bit Single-Supply Voltage-Output DAC; Package: LQFP (10x10mm); No of Pins: 52; Temperature Range: Industrial |
| 中文描述： | SPECIALTY ANALOG CIRCUIT, PDSO20 |
| 封裝： | SSOP-20 |
| 文件頁數： | 7/32頁 |
| 文件大?。?/td> | 530K |
| 代理商： | ADE7759ARS |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
REV. 0
–7–
ADE7759
PIN FUNCTION DESCRIPTIONS
Pin No.
Mnemonic
Description
1
RESET
Reset Pin for the ADE7759. A logic low on this pin will hold the ADCs and digital circuitry
(including the serial interface) in a reset condition.
Digital Power Supply. This pin provides the supply voltage for the digital circuitry in the ADE7759.
The supply voltage should be maintained at 5 V
±
5% for specified operation. This pin should be
decoupled to DGND with a 10
μ
F capacitor in parallel with a ceramic 100 nF capacitor.
Analog Power Supply. This pin provides the supply voltage for the analog circuitry in the ADE7759.
The supply should be maintained at 5 V
±
5% for specified operation. Every effort should be made
to minimize power supply ripple and noise at this pin by the use of proper decoupling method.
This pin should be decoupled to AGND with a 10
μ
F capacitor in parallel with a ceramic 100 nF
capacitor.
Analog Inputs for Channel 1. This channel is intended for use with the di/dt current transducers
such as Rogowski coil, or other current sensors such as shunt or current transformer (CT). These
inputs are fully differential voltage inputs with maximum differential input signal levels of
±
0.5 V,
±
0.25 V and
±
0.125 V, depending on the full scale selection—See Analog Inputs section. Channel
1 also has a PGA with gain selections of 1, 2, 4, 8, or 16. The maximum signal level at these pins
with respect to AGND is
±
0.5 V. Both inputs have internal ESD protection circuitry. In addition,
an overvoltage of
±
6 V can be sustained on these inputs without risk of permanent damage.
Analog Inputs for Channel 2. This channel is intended for use with the voltage transducer. These inputs
are fully differential voltage inputs with a maximum differential signal level of
±
0.5 V. Channel 2
also has a PGA with gain selections of 1, 2, 4, 8, or 16. The maximum signal level at these pins
with respect to AGND is
±
0.5 V. Both inputs have internal ESD protection circuitry, and an over-
voltage of
±
6 V can be sustained on these inputs without risk of permanent damage.
This pin provides the ground reference for the analog circuitry in the ADE7759, i.e., ADCs and
reference. This pin should be tied to the analog ground plane or the quietest ground reference in
the system. This quiet ground reference should be used for all analog circuitry, e.g., antialiasing
filters, current and voltage transducers, etc. In order to keep ground noise around the ADE7759
to a minimum, the quiet ground plane should be connected to the digital ground plane at only
one point. It is acceptable to place the entire device on the analog ground plane—see Application
Information section.
This pin provides access to the on-chip voltage reference. The on-chip reference has a nominal
value of 2.4 V
±
8% and a typical temperature coefficient of 20 ppm/
°
C. An external reference
source may be connected at this pin. In either case this pin should be decoupled to AGND with
a 1
μ
F capacitor in parallel with a 100 nF capacitor.
This provides the ground reference for the digital circuitry in the ADE7759, i.e., multiplier, filters,
and frequency output (CF). Because the digital return currents in the ADE7759 are small, it is
acceptable to connect this pin to the analog ground plane of the system—see Application Information
section. However, high bus capacitance on the DOUT pin may result in noisy digital current that
affects performance.
Calibration Frequency Logic Output. The CF logic output gives Active Power information. This
output is intended to be used for operational and calibration purposes. The full-scale output fre-
quency can be adjusted by writing to the APGAIN, CFNUM and CFDEN Registers—see Energy
to Frequency Conversion section
.
2
DV
DD
3
AV
DD
4, 5
V1P, V1N
6, 7
V2N, V2P
8
AGND
9
REF
IN/OUT
10
DGND
11
CF
PIN CONFIGURATION
TOP VIEW
(Not to Scale)
ADE7759
RESET
DIN
DV
DD
DOUT
AV
DD
SCLK
V1P
CS
V1N
CLKOUT
V2N
CLKIN
V2P
IRQ
AGND
SAG
REF
IN/OUT
ZX
DGND
CF
20
19
18
17
16
15
14
13
12
11
1
2
3
4
5
6
7
8
9
10
相關PDF資料 |
PDF描述 |
|---|---|
| ADE7759 | Active Energy Metering IC with di/dt Sensor Interface |
| ADE7760ARSRL | Energy Metering IC with On-Chip Fault Detection |
| ADE7760 | 8-Channel 14-Bit Single-Supply Voltage-Output DAC; Package: LQFP (10x10mm); No of Pins: 52; Temperature Range: Industrial |
| ADE7760ARS | Energy Metering IC with On-Chip Fault Detection |
| ADE7762 | Polyphase Energy Metering IC with Phase Drop Indication |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADE7759ARSRL | 功能描述:IC ENERGY METERING 1PHASE 20SSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 能量測量 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:* |
| ADE7759ARSZ | 功能描述:IC ENERGY METERING 1PHASE 20SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 能量測量 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:* |
| ADE7759ARSZRL | 功能描述:IC ENERGY METERING 1PHASE 20SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 能量測量 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:* |
| ADE7760 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Energy Metering IC with On-Chip Fault Detection |
| ADE7760ARS | 制造商:Analog Devices 功能描述:Energy Measurement 20-Pin SSOP 制造商:Analog Devices 功能描述:ENERGY METER IC W/ ONCHIP FAULT & OSCIL. - Rail/Tube |
發布緊急采購，3分鐘左右您將得到回復。