參數資料
型號: ADDAC80NZ-CBI-V
廠商: Analog Devices Inc
文件頁數: 3/16頁
文件大?。?/td> 0K
描述: IC DAC 12-BIT BINARY MONO 24-DIP
產品培訓模塊: Data Converter Fundamentals
DAC Architectures
標準包裝: 15
設置時間: 2µs
位數: 12
數據接口: 并聯
轉換器數目: 1
電壓電源: 雙 ±
功率耗散(最大): 300mW
工作溫度: 0°C ~ 70°C
安裝類型: 通孔
封裝/外殼: 24-DIP(0.600",15.24mm)
供應商設備封裝: 24-PDIP
包裝: 管件
輸出數目和類型: 1 電壓,單極;1 電壓,雙極
采樣率(每秒): *
產品目錄頁面: 785 (CN2011-ZH PDF)
REV. B
ADDAC80/ADDAC85/ADDAC87
–11–
VOLTAGE OUTPUT MODELS
Internal scaling resistors provided in the ADDAC80 may be
connected to produce bipolar output voltage ranges of
±10 V,
±5 V or ±2.5 V or unipolar output voltage ranges of 0 V to +5 V
or 0 V to +10 V (see Figure 9).
REF
INPUT
TO REF
CONTROL
CIRCUIT
FROM
WEIGHTED
RESISTOR
NETWORK
SUMMING
JUNCTION
6.3k
5k
18
20
16
+
OUTPUT
COM
BIPOLAR
OFFSET
21
15
19
17
Figure 9. Output Amplifier Voltage Range Scaling Circuit
Gain and offset drift are minimized in the ADDAC80 because
of the thermal tracking of the scaling resistors with other device
components. Connections for various output voltage ranges are
shown in Table III. Settling time is specified for a full-scale
range change: 4 s for a 10 k
feedback resistor; 3 s for a 5 k
feedback resistor when using the compensation capacitor shown
in Figure 3a.
The equivalent resistive scaling network and output circuit of
the current model are shown in Figures 10 and 11. External RLS
resistors are required to produce exactly 0 V to –2 V or
± 1 V
output. TCR of these resistors should be
±100 ppm/°C or less
to maintain the ADDAC80 output specifications. If exact output
ranges are not required, the external resistors are not needed.
17
TO REF CONTROL CIRCUIT
6.3k
3k
2k
19
20
16
18
REF IN
5k
15
Figure 10. Internal Scaling Resistors
6.3k
BIPOLAR OFFSET
REFERENCE
INPUT
IOUT
COMMON
REFERENCE OUT
6.6k
V
TO REF
CONTROL
CIRCUIT
17
16
I
0 TO 2mA
6.3V
24
21
15
+
Figure 11. ADDAC80 Current Model Equivalent Output Circuit
Internal resistors are provided to scale an external op amp or to
configure a resistive load to offer two output voltage ranges of
±1 V
or 0 V to –2 V. These resistors (RLI TCR = 20 ppm/
°C) are an
integral part of the ADDAC80 and maintain gain and bipolar
offset drift specifications. If the internal resistors are not used, exter-
nal RL (or RF) resistors should have a TCR of
±25 ppm/°C or
less to minimize drift. This will typically add
±50 ppm/°C + the
TCR of RL (or RF) to the total drift.
Table III. Output Voltage Range Connections, Voltage Model ADDAC80
Output
Digital
Connect
Range
Input Codes
Pin 15 to
Pin 17 to
Pin 19 to
Pin 16 to
±10 V
COB or CTC
19
20
15
24
±5 V
COB or CTC
18
20
NC
24
±2.5 V
COB or CTC
18
20
24
0 V to 10 V
CSB
18
21
NC
24
0 V to 5 V
CSB
18
21
20
24
0 V to 10 V
CCD
19
NC
15
24
NC = No Connect
DRIVING A RESISTIVE LOAD UNIPOLAR
A load resistance, RL = RLI, + RLS, connected as shown in
Figure 12 will generate a voltage range, VOUT, determined by:
VmA
kR
OUT
L
=
×
+
.
2
66
(1)
where RL max = 1.54 k
and V
OUT max = –2.5 V
To achieve specified drift, connect the internal scaling resistor
(RLI) as shown in Table IV to an external metal film trim resistor
(RLS) to provide full scale output voltage range of 0 V to –2 V.
With RLS = 0 V, VOUT = –1.69 V.
0 TO
2mA
CURRENT CONTROLLED
BY DIGITAL INPUT
6.6k
RLI
968
COMMON
VOUT
RLS
+
15
18
21
Figure 12. Equivalent Circuit ADDAC80-CBI-I Connected
for Unipolar Voltage Output with Resistive Load
相關PDF資料
PDF描述
MS27497T24F24SB CONN RCPT 24POS WALL MNT W/SCKT
MS27508E10A35AA CONN HSG RCPT 13POS BOX MT PIN
AD7547JRZ IC DAC 12BIT DUAL LC2MOS 24-SOIC
MS27497T18B35SLC CONN HSG RCPT 66POS WALL MT SCKT
MS3456L32-63S CONN PLUG 5POS STRAIGHT W/SCKT
相關代理商/技術參數
參數描述
ADDAC80NZ-CBI-V 制造商:Analog Devices 功能描述:IC, DAC, 12BIT, DIP-24
ADDAC80Z-CBI-I 制造商:AD 制造商全稱:Analog Devices 功能描述:COMPLETE LOW COST 12-BIT D/A CONVERTERS
ADDAC80Z-CBI-V 制造商:Analog Devices 功能描述:DAC 1CH CURRENT STEERING 12-BIT 24PIN SBCDIP - Bulk
ADDAC80ZCCDI 制造商:AD 功能描述:80 ANALOG DEVICE S8M6A
ADDAC80Z-CCD-I 制造商:Rochester Electronics LLC 功能描述:- Bulk