- 您現在的位置：買賣IC網 > PDF目錄16543 > ADA4859-3ACP-EBZ (Analog Devices Inc)BOARD EVAL FOR ADA4859-3ACP PDF資料下載
參數資料
| 型號： | ADA4859-3ACP-EBZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 4/16頁 |
| 文件大?。?/td> | 0K |
| 描述： | BOARD EVAL FOR ADA4859-3ACP |
| 標準包裝： | 1 |
| 系列： | * |
ADA4859-3
Data Sheet
Rev. A | Page 12 of 16
THEORY OF OPERATION
OVERVIEW
The ADA4859-3 is a fixed gain of two, current feedback amplifier
designed for exceptional performance as a triple video amplifier. Its
specifications make it especially suitable for SD and HD video
applications. The ADA4859-3 provides HD video output on a
single supply as low as 3.0 V while only consuming 13 mA per
amplifier. It also features a power-down pin (PD) that reduces
the quiescent current to 4 mA when activated.
The ADA4859-3 can be used in applications that require both
ac- and dc-coupled inputs and outputs. The output stage on the
ADA4859-3 is capable of driving 2 V p-p video signals into two
doubly terminated video loads (150 each) on a single 5 V supply.
The input range of the ADA4859-3 includes ground, whereas
the output range is limited by the output headroom set by the
voltage drop across two diodes from each rail, which occurs
1.2 V from the positive and negative supply rails.
CHARGE PUMP OPERATION
The on-board charge pump creates a negative supply for the
amplifier. It provides different negative voltages depending on
the power supply voltage. For a +5 V supply, the negative supply
generated is equal to 3 V with 150 mA of output supply current,
and for a +3.3 V supply, the negative supply is equal to 2 V
with 45 mA of output supply current.
charges C1 through Φ1 to ground. During this cycle, C1 quickly
charges to reach the +VS voltage. The discharge cycle then begins
When C1 = C2, the charge in C1 is divided between the two
capacitors and slowly increases the voltage in C2 until it reaches a
predetermined voltage (3 V for the +5 V supply and 2 V for
the +3.3 V supply). The typical charge pump charging and
discharging frequency is 550 kHz with a 150 load and no input
signal. This frequency changes with the load current, and it can
get much slower if the amplifier is powered down and no external
current is used.
07715-
137
+VS
CPO
C2
C1
Φ1
a
b
Figure 30. Charging Cycle
07715-
138
+VS
CPO
C2
C1
Φ2
a
b
Figure 31. Discharging Cycle
The ADA4859-3 specifications make it especially suitable for SD
and HD video applications. It also allows dc-coupled video signal
with its black level set to 0 V and its sync tip down to 300 mV
for YPbPr video.
The charge pump is always on, even when the power-down pin
(PD) is enabled and the amplifier is off. However, it would be in
an idle state if the negative current were not used. Each amplifier
needs 6.3 mA of current, which totals 19 mA for all three
amplifiers. This means additional negative current may be available
by the charge pump for external use. Pin 4 (CPO) is the charge
pump output, which provides access to the negative supply
generated by the charge pump. Placing a 1 F charge capacitor at
the CPO pin is essential to hold the charge and regulate the ripple.
If the negative supply is used to power another device in the
system, it is only possible for the 5 V supply operation. In the
3.3 V supply operation, the charge pump output current is very
limited. The capacitor at the CPO pin, which regulates the ripple
of the negative voltage, can be used as a coupling capacitor for the
external device. However, the charge pump current should be
limited to a maximum of 50 mA for external use. When powering
down the ADA4859-3, the charge pump is not affected and its
output voltage and current remain available for external use.
相關PDF資料 |
PDF描述 |
|---|---|
| AD8280-EVALZ | BOARD EVAL FOR AD8280 |
| ECE-T2WP681EA | CAP ALUM 680UF 450V 20% SNAP |
| ECM22DRTH-S13 | CONN EDGECARD 44POS .156 EXTEND |
| MCP130T-270I/TT | IC SUPERVISOR 2.70V LOW SOT23 |
| ECE-T1JA273FA | CAP ALUM 27000UF 63V 20% SNAP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADA4859-3ACPZ-R2 | 制造商:Analog Devices 功能描述:VID AMP TRIPLE 5.5V 16LFCSP EP - Tape and Reel 制造商:Rochester Electronics LLC 功能描述: 制造商:Analog Devices 功能描述:IC VIDEO AMPLIFIER TRI 195MHZ LFCSP16 制造商:Analog Devices 功能描述:Sngl Sup HghSpd GN+2 Amp Chrg Pump 制造商:Analog Devices 功能描述:IC, VIDEO AMPLIFIER, TRI, 195MHZ LFCSP16, Gain Bandwidth:195MHz, Supply Voltage Range:3V to 5.5V, Slew Rate:740V/s, No. of Amplifiers:3, Output Current:19mA, Amplifier Output:Single Ended, Operating Temperature Range:-40C to +105C, RoHS Compliant: Yes |
| ADA4859-3ACPZ-R7 | 功能描述:IC AMP 3CH CFB G=2 W/CP 16LFCSP RoHS:是 類別:集成電路 (IC) >> 線性 - 放大器 - 視頻放大器和頻緩沖器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 應用:TFT-LCD 面板：VCOM 驅動器 輸出類型:滿擺幅 電路數:1 -3db帶寬:35MHz 轉換速率:40 V/µs 電流 - 電源:3.7mA 電流 - 輸出 / 通道:1.3A 電壓 - 電源，單路/雙路(±):9 V ~ 20 V，±4.5 V ~ 10 V 安裝類型:表面貼裝 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬）裸露焊盤 供應商設備封裝:8-uMax-EP 包裝:管件 |
| ADA4859-3ACPZ-RL | 功能描述:IC AMP 3CH CFB G=2 W/CP 16LFCSP RoHS:是 類別:集成電路 (IC) >> 線性 - 放大器 - 視頻放大器和頻緩沖器 系列:- 標準包裝:1,000 系列:- 應用:驅動器 輸出類型:差分 電路數:3 -3db帶寬:350MHz 轉換速率:1000 V/µs 電流 - 電源:14.5mA 電流 - 輸出 / 通道:60mA 電壓 - 電源，單路/雙路(±):5 V ~ 12 V，±2.5 V ~ 6 V 安裝類型:表面貼裝 封裝/外殼:20-VFQFN 裸露焊盤 供應商設備封裝:20-QFN 裸露焊盤（4x4） 包裝:帶卷 (TR) |
| ADA4860-1 | 制造商:AD 制造商全稱:Analog Devices 功能描述:High Speed, Low Cost, Op Amp |
| ADA4860-1YRJ-EBZ | 功能描述:BOARD EVAL FOR ADA4860-1YRJ RoHS:是 類別:編程器，開發系統 >> 評估板 - 運算放大器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- |
發布緊急采購，3分鐘左右您將得到回復。