- 您現在的位置：買賣IC網 > PDF目錄2139 > ADA4830-1BCPZ-R7 (Analog Devices Inc)IC AMP BATT PROTECT 8LFCSP PDF資料下載
參數資料
| 型號： | ADA4830-1BCPZ-R7 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 4/16頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC AMP BATT PROTECT 8LFCSP |
| 標準包裝： | 1,500 |
| 放大器類型： | 差分 |
| 電路數： | 1 |
| 轉換速率： | 220 V/µs |
| -3db帶寬： | 84MHz |
| 電流 - 電源： | 6.8mA |
| 電流 - 輸出 / 通道： | 125mA |
| 電壓 - 電源，單路/雙路(±)： | 2.9 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-WFDFN 裸露焊盤，CSP |
| 供應商設備封裝： | 8-LFCSP（3x3） |
| 包裝： | 帶卷 (TR) |
| 其它名稱： | ADA4830-1BCPZ-R7TR |
ADA4830-1
Data Sheet
Rev. 0 | Page 12 of 16
Approximate minimum and maximum CM voltages are shown
in Table 6 for several common supply voltages.
Table 6.
+V
S (V)
V
REF (V)
V
INCM(MIN) (V)
V
INCM(MAX) (V)
3.0
1.51
–7.0
2.8
3.0
0.97
–4.9
4.9
3.3
1.671
–7.6
3.6
3.3
1.15
–5.6
5.6
3.6
–8.2
4.5
3.6
1.34
–6.4
6.4
5.0
–10
8.7
5.0
2.22
–9.9
9.9
1 Floating (default condition).
Figure 24. Input Common-Mode Range vs. Supply Voltage
SHORT TO BATTERY OUTPUT FLAG PIN
The flag output (STB pin) is of an active low, open-drain logic
style. A low level on this output indicates that more than 11 V
has been detected on either the positive or the negative input.
Flags from multiple chips may be wire-or'ed to form a single
fault detection signal. The output is driven by a grounded source
NMOS device, capable of sinking approximately 10 mA while
pulling within 100 mV of ground. The output high level is set
with an external pull-up resistor connected to the supply voltage
of the logic family that is used to monitor the state of the flag.
The speed with which the flag output responds primarily
depends, in the falling direction, on the external capacitance
attached to this node and the sink current that can be provided.
For example, if the load is 10 pF, and the external pull-up voltage is
3.3 V, the fall time is a few nanoseconds. In the rising direction,
the speed is determined by external capacitance and the
magnitude of the pull-up resistor. For the case of 10 pF of
external capacitance and a pull-up of 5 k, the time constant
of the rising edge is approximately 50 ns.
Table 7. STB Pin Function
STB Pin Output
Device State
High (Logic 1)
Normal operation
Low (Logic 0)
STB fault condition
ENABLE/DISABLE MODES (ENA PIN)
The power-down, or enable/disable (ENA) pin, is internally
pulled up to +VS through a 250 k resistor. When the voltage
on this pin is high, the amplifier is enabled; pulling ENA low
disables the channel. With no external connection, this pin
floats high, enabling the amplifier channel.
Table 8. ENA Pin Function
ENA Pin Input
Device State
High (Logic 1)
Enabled
Low (Logic 0)
Disabled
PCB LAYOUT
As with all high speed applications, attention to PCB layout is of
paramount importance. Adhere to standard high speed layout
practices in designs using the ADA4830-1. A solid ground plane
is recommended, and placing a 0.1 F surface-mount, ceramic
power supply, decoupling capacitor as close as possible to the
supply pin is recommended.
Connect the GND pin(s) to the ground plane with a trace that is
as short as possible. In cases where the ADA4830-1 drives trans-
mission lines, series terminate the outputs and use controlled
impedance traces of the shortest length possible to connect to
the signal I/O pins, which should not pass over any voids in the
ground plane.
EXPOSED PADDLE (EPAD) CONNECTION
The ADA4830-1 has an exposed thermal pad (EPAD) on the
bottom of the package. This pad is not electrically connected
to the die and can be left floating or connected to the ground
plane. Should heat dissipation be a concern, thermal resistance
can be minimized by soldering the EPAD to a metalized pad on
the PCB. Connect this pad to the ground plane with multiple
vias. Note that the thermal resistance (θJA) of the device is
specified with the EPAD soldered to the PCB.
–15
–10
–5
0
5
10
15
2.5
3.0
3.5
4.0
4.5
5.0
5.5
6.0
IN
PU
T
C
O
MMO
N
-MO
D
E
VO
LT
A
G
E
(V)
SUPPLY VOLTAGE (V)
VINCM (MAX)
VINCM (MIN)
VREF PIN FLOATING
10020-
037
相關PDF資料 |
PDF描述 |
|---|---|
| ADA4830-2BCPZ-R7 | IC AMP BATT PROTECT DUAL 16LFCSP |
| ADA4841-2YRZ-R7 | IC OPAMP VF R-R DUAL LP LN 8SOIC |
| ADA4850-2YCPZ-R2 | IC OPAMP VF R-R DUAL 16LFCSP |
| ADA4851-4YRUZ | IC OPAMP VF R-R QUAD LP 14TSSOP |
| ADA4855-3YCPZ-R7 | IC OPAMP VF R-R TRPL LP 16LFCSP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADA4830-1WBCPZ-R7 | 制造商:AD 制造商全稱:Analog Devices 功能描述:High Speed Difference Amplifier with Input |
| ADA4830-2 | 制造商:AD 制造商全稱:Analog Devices 功能描述:High Speed Difference Amplifier with Input |
| ADA4830-2BCPZ-R2 | 制造商:Analog Devices 功能描述:AMP DIFF DUAL 71MHZ 16LFCSP 制造商:Analog Devices 功能描述:AMP, DIFF, DUAL, 71MHZ, 16LFCSP |
| ADA4830-2BCPZ-R7 | 功能描述:IC AMP BATT PROTECT DUAL 16LFCSP RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 產品培訓模塊:Differential Circuit Design Techniques for Communication Applications 標準包裝:1 系列:- 放大器類型:RF/IF 差分 電路數:1 輸出類型:差分 轉換速率:9800 V/µs 增益帶寬積:- -3db帶寬:2.9GHz 電流 - 輸入偏壓:3µA 電壓 - 輸入偏移:- 電流 - 電源:40mA 電流 - 輸出 / 通道:- 電壓 - 電源，單路/雙路(±):3 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-VQFN 裸露焊盤，CSP 供應商設備封裝:16-LFCSP-VQ 包裝:剪切帶 (CT) 產品目錄頁面:551 (CN2011-ZH PDF) 其它名稱:ADL5561ACPZ-R7CT |
| ADA4830-2WBCPZ-R7 | 制造商:AD 制造商全稱:Analog Devices 功能描述:High Speed Difference Amplifier with Input |
發布緊急采購，3分鐘左右您將得到回復。