- 您現在的位置：買賣IC網 > PDF目錄373972 > AD9956 (Analog Devices, Inc.) 2.7 GHz DDS-Based AgileRF PDF資料下載
參數資料
| 型號： | AD9956 |
| 廠商： | Analog Devices, Inc. |
| 英文描述： | 2.7 GHz DDS-Based AgileRF |
| 中文描述： | 2.7千兆赫基于DDS的AgileRF |
| 文件頁數： | 30/32頁 |
| 文件大?。?/td> | 805K |
| 代理商： | AD9956 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁當前第30頁第31頁第32頁
AD9956
CFR2<28:26> Clock Driver Falling Edge Control
These bits control the slew rate of the CML clock driver output’s
falling edge. When these bits are on, additional current is sent to
the output driver to increase the rising edge slew rate capability.
Table 7 describes how the bits increase the current; the contri-
butions of each bit are cumulative. Note that the additional cur-
rent is on only during the rising edge of the waveform, for ap-
proximately 250 ps, but not on during the entire transition.
Table 7. CML Clock Drive Falling Edge Slew Rate
Control Bits and Associated Surge Current
CFR2<28> = 1
CFR2<30> = 1
CFR2<29> = 1
Rev. 0 | Page 30 of 32
5.4 mA
2.7 mA
1.35 mA
CFR2<25> PLL_LOCK_DETECT Enable
This bit enables the PLL_LOCK/SYNC_IN pin as a lock detect
output for the PLL.
CFR2<25> = 0 (default).The PLL_LOCK_DETECT signal is
disabled.
CFR2<25> = 1. The PLL_LOCK_DETECT signal is enabled.
CFR2<24> PLL_LOCK_DETECT Mode
This bit toggles the modes of the PLL_LOCK_DETECT func-
tion. The lock detect can either be a status indicator (locked or
unlocked), or it can indicate a lead-lag relationship between the
two phase frequency detector inputs.
CFR2<24> = 0 (default). The lock detect acts as a status indica-
tor (PLL is locked 0 or unlocked 1).
CFR2<24> = 1. The lock detect acts as a lead/lag indicator. A
1 on the PLL_LOCK pin means that the PLLOSC pin lags the
reference. A 0 means that the PLLOSC pin leads the reference.
CFR2<23> RF Divider Power-Down
This bit powers the RF divider down to save power when not in
used.
CFR2<23> = 0 (default). RF divider is on.
CFR2<23> = 1. RF divider is powered down and an alternate
path between the REFCLK inputs and SYSCLK is enabled.
CFR2<22:21> RF Divider Ratio
These two bits control the RF divider ratio (÷R).
CFR2<22:21> = 11 (default). RF Divider R = 8.
CFR2<22:21> = 10. RF Divider R= 4.
CFR2<22:21> = 01. RF Divider R = 2.
CFR2<22:21> = 00. RF Divider R = 1. Note that this is not the
same as bypassing the RF divider.
CFR2<20> Clock Driver Power-Down
This bit powers down the CML clock driver circuit.
CFR2<20> =1 (default). CML clock driver circuit is powered down.
CFR2<20> = 0. CML clock driver is powered up.
CFR2<19:18> Clock Driver Input Select
These bits control the mux on the input for the CML clock driver.
CFR2<19:18> = 00. The CML clock driver is disconnected from
all inputs (and does not toggle).
CFR2<19:18> = 01. The CML clock driver is driven by the
PLLOSC input pin.
CFR2<19:18> = 10 (default). The CML clock driver is driven by
the output of the RF divider.
CFR2<19:18> = 11. The CML clock driver is driven by the input
of the RF divider
CFR2<17> Slew Rate Control Bit
Even without the additional surge current supplied by the rising
edge slew rate control bits and the falling edge slew rate control
bits, the device applies a default 7.6 mA surge current to the
rising edge and a 4.05 mA surge current to the falling edge. This
bit disables all slew rate enhancement surge current, including
the default values.
CFR2<17> = 0 (default). The CML driver applies default surge
current to rising and falling edges.
CFR2<17> = 1. Driver applies no surge current during transi-
tions. The only current is the continuous current.
CFR2<16> RF Divider SYSCLK Mux Bit
This bit toggles the mux to control whether the RF divider out-
put or input is supplying SYSCLK to the device.
CFR2<16> = 0 (default). The RF divider output supplies the
DDS SYSCLK.
CFR2<16> = 1. The RF divider input supplies the DDS SYSCLK
(bypass the divider). Note that regardless of the condition of the
configuration of the clock input, the DDS SYSCLK must not
exceed the maximum rated clock speed.
相關PDF資料 |
PDF描述 |
|---|---|
| AD9956YCPZ-REEL1 | 2.7 GHz DDS-Based AgileRF |
| AD9956YCPZ1 | 2.7 GHz DDS-Based AgileRF |
| AD9957 | 1 GSPS Quadrature Digital Upconverter with 18-Bit IQ Data Path and 14-Bit DAC |
| AD9957BSVZ | 1 GSPS Quadrature Digital Upconverter with 18-Bit IQ Data Path and 14-Bit DAC |
| AD9957BSVZ-REEL | 1 GSPS Quadrature Digital Upconverter with 18-Bit IQ Data Path and 14-Bit DAC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD9956/PCB | 制造商:Analog Devices 功能描述:Evaluation Board For AD9956, 2.7 GHz DDS-Based AgileRF Synthesizer 制造商:Analog Devices 功能描述:EVAL BD FOR AD9956, 2.7 GHZ DDS-BASED AGILERF SYNTHESIZER - Trays 制造商:Rochester Electronics LLC 功能描述:400 MSPS 14 BIT DDS EVAL BD. - Bulk |
| AD9956/PCBZ | 功能描述:BOARD EVAL FOR AD9956 RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:AgileRF™ 標準包裝:1 系列:PSoC® 主要目的:電源管理，熱管理 嵌入式:- 已用 IC / 零件:- 主要屬性:- 次要屬性:- 已供物品:板，CD，電源 |
| AD9956-VCO/PCB | 制造商:Analog Devices 功能描述:EVAL BD FOR AD9956, 2.7 GHZ DDS-BASED AGILERF SYNTHESIZER - Trays 制造商:Analog Devices 功能描述:EVAL CARD ((NS)) |
| AD9956-VCO/PCBZ | 功能描述:BOARD EVAL 14BIT 1.8V 48LFCSP RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:AgileRF™ 標準包裝:1 系列:PSoC® 主要目的:電源管理，熱管理 嵌入式:- 已用 IC / 零件:- 主要屬性:- 次要屬性:- 已供物品:板，CD，電源 |
| AD9956XCPZ | 制造商:Analog Devices 功能描述:DGTL SYNTHESIZER 48LFCSP EP - Tape and Reel |
發布緊急采購，3分鐘左右您將得到回復。