- 您現在的位置：買賣IC網 > PDF目錄373970 > AD9877 (Analog Devices, Inc.) Mixed-Signal Front End Set-Top Box, Cable Modem PDF資料下載
參數資料
| 型號： | AD9877 |
| 廠商： | Analog Devices, Inc. |
| 英文描述： | Mixed-Signal Front End Set-Top Box, Cable Modem |
| 中文描述： | 混合信號前端機頂盒，電纜調制解調器 |
| 文件頁數： | 29/36頁 |
| 文件大?。?/td> | 1094K |
| 代理商： | AD9877 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁當前第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
AD9877
PROGRAMMING THE AD8321/AD8325 OR AD8322/AD8327 CABLE DRIVER AMPLIFIER
GAIN CONTROL
Programming the gain of the AD832x family cable driver
amplifier can be accomplished via the AD9877 cable amplifier
control interface. Four 8-bit registers within the AD9877 (one
per profile) store the gain value to be written to the serial 3-wire
port. Typically either AD8321/AD8325 or AD8322/AD8327
variable gain cable amplifiers are connected to the chip’s 3-wire
cable amplifier interface. The Tx gain control select bit in
Register 0x0F changes the interpretation of the bits in Registers
0x13, 0x17, 0x1B, and 0x1F. See the Cable Driver Gain Control
section register description.
Rev. B | Page 29 of 36
Data transfers to the gain programmable cable driver amplifier
are initiated by the following four conditions.
1.
Power-Up and Hardware Reset—Upon initial power-up
and every hardware reset, the AD9877 clears the contents
of the gain control registers to 0, which defines the lowest
gain setting of the AD832x. Thus, the AD9877 writes all 0s
out of the 3-wire cable amplifier control interface.
2.
Software Reset—Writing a 1 to Bit 5 of Address 0x00
initiates a software reset. Upon a software reset, the
AD9877 clears the contents of the gain control registers to
0 for the lowest gain and sets the profile select to 0. The
AD9877 writes all 0s out of the 3-wire cable amplifier
control interface if the gain was previously on a different
setting (other than 0).
3.
Change in Profile Selection—The AD9877 samples the
PROFILE(1) and PROFILE(2) input pins together with the
two profile select bits and writes to the AD832x gain
control registers if a change in profile and gain is
determined. The data written to the cable driver amplifier
comes from the AD9877 gain control register associated
with the current profile.
4.
Write to AD9877 Cable Driver Amplifier Control
Registers—The AD9877 will write gain control data
associated with the current profile to the AD832x
whenever the selected AD9877 cable driver amplifier gain
setting is changed.
Once a new stable gain value has been detected (48 MCLK to
64 MCLK cycles after initiation), a data write starts with CA_CS
going low. The AD9877 always finishes a write sequence to the
cable driver amplifier once it is started. The logic controlling
data transfers to the cable driver amplifier uses up to 200 MCLK
cycles and is designed to prevent erroneous write cycles from
occurring.
相關PDF資料 |
PDF描述 |
|---|---|
| AD9877ABS | Mixed-Signal Front End Set-Top Box, Cable Modem |
| AD9877-EB | Mixed-Signal Front End Set-Top Box, Cable Modem |
| AD9882KST-100 | Dual Interface for Flat Panel Displays |
| AD9882KST-140 | Dual Interface for Flat Panel Displays |
| AD9882 | Dual Interface for Flat Panel Displays |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD9877ABS | 制造商:Rochester Electronics LLC 功能描述: 制造商:Analog Devices 功能描述: |
| AD9877ABS-1 | 制造商:Analog Devices 功能描述: |
| AD9877ABSZ | 功能描述:IC PROCESSOR FRONT END 100MQFP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模擬前端 (AFE) 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 位數:- 通道數:2 功率（瓦特）:- 電壓 - 電源，模擬:3 V ~ 3.6 V 電壓 - 電源，數字:3 V ~ 3.6 V 封裝/外殼:32-VFQFN 裸露焊盤 供應商設備封裝:32-QFN（5x5） 包裝:帶卷 (TR) |
| AD9877BS | 制造商:Analog Devices 功能描述: |
| AD9877-EB | 制造商:Analog Devices 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。