- 您現在的位置：買賣IC網 > PDF目錄17021 > AD9284-250EBZ (Analog Devices Inc)BOARD EVAL FOR AD9284 PDF資料下載
參數資料
| 型號： | AD9284-250EBZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 5/24頁 |
| 文件大小： | 0K |
| 描述： | BOARD EVAL FOR AD9284 |
| 標準包裝： | 1 |
| ADC 的數量： | 2 |
| 位數： | 8 |
| 采樣率（每秒）： | 250M |
| 數據接口： | 串行，SPI? |
| 輸入范圍： | 1.2 Vpp |
| 工作溫度： | -40°C ~ 85°C |
| 已用 IC / 零件： | AD9284 |
| 已供物品： | 板 |
| 相關產品： | AD9284BCPZ-250-ND - IC ADC 8BIT 250MSPS 1.8V 48LFCSP AD9284BCPZRL7-250-ND - IC ADC 8BIT 250MSPS 1.8V 48LFCSP |
Data Sheet
AD9284
Rev. A | Page 13 of 24
THEORY OF OPERATION
The AD9284 is a pipeline-type converter. The input buffers are
differential, and both sets of inputs are internally biased. This
allows the use of ac or dc input modes. A sample-and-hold
amplifier is incorporated into the first stage of the multistage
pipeline converter core. The output staging block aligns the
data, carries out error correction for the pipeline stages, and
feeds that data to the output buffers. The two ADC channels
are sampled simultaneously through a single encoding clock.
All user-selected options are programmed through dedicated
digital input pins or a serial port interface (SPI).
ADC ARCHITECTURE
Each channel of the AD9284 consists of a differential input
buffer followed by a sample-and-hold amplifier (SHA). The
SHA is followed by a pipeline switched-capacitor ADC. The
quantized outputs from each stage are combined into a final
8-bit result in the digital correction logic. The pipelined
architecture permits the first stage to operate on a new input
sample, whereas the remaining stages operate on preceding
samples.
Each stage of the pipeline, excluding the last, consists of a low
resolution flash ADC connected to a switched-capacitor DAC
and interstage residue amplifier (MDAC). The residue amplifier
magnifies the difference between the reconstructed DAC output
and the flash input for the next stage in the pipeline. One bit of
redundancy is used in each stage to facilitate digital correction
of flash errors. The last stage consists of a flash ADC.
The input stage contains a differential SHA that can be ac- or
dc-coupled in differential or single-ended mode. The output
staging block aligns the data, carries out error correction, and
passes the data to the output buffers. The output buffers are
powered from a separate supply, allowing adjustment of the
output voltage swing. During power-down, the output buffers
enter a high impedance state.
ANALOG INPUT CONSIDERATIONS
The analog inputs of the AD9284 are differentially buffered.
For best dynamic performance, the source impedances driving
VIN+A, VIN+B, VINA, and VINB should be matched such
that common-mode settling errors are symmetrical. The analog
inputs are optimized to provide superior wideband performance
and must be driven differentially. SNR and SINAD performance
degrades significantly if the analog inputs are driven with a single-
ended signal.
A wideband transformer, such as Mini-Circuits ADT1-1WT,
can provide the differential analog inputs for applications that
require a single-ended-to-differential conversion. Both analog
inputs are self-biased by an on-chip resistor divider to
a nominal 1.4 V.
Differential Input Configurations
Optimum performance is achieved when driving the AD9284
in a differential input configuration. For baseband applications,
the ADA4937-1 differential driver provides excellent performance
and a flexible interface to the ADC (see Figure 19). The output
common-mode voltage of the AD9284 is easily set to 1.4 V, and
the driver can be configured in a Sallen-Key filter topology to
provide band limiting of the input signal.
–
+
200
227.4
61.9
ADA4937-1
1.2V p-p
0.1F
200
4.7pF
33
VIN
+
–
AD9284
VCM
09085-
025
Figure 19. Differential Input Configuration Using the ADA4937-1
The AD9284 can also be driven passively with a differential
transformer-coupled input (see Figure 20). To bias the analog
input, the VCM voltage can be connected to the center tap of
the secondary winding of the transformer.
49.9
1.2V p-p
4.7pF
0.1F
33
VIN
+
–
AD9284
VCM
09085-
026
Figure 20. Differential Transformer-Coupled Configuration
The signal characteristics must be considered when selecting a
transformer. Most RF transformers saturate at frequencies below
a few megahertz (MHz). Excessive signal power can also cause
core saturation, which leads to distortion.
VOLTAGE REFERENCE
An internal differential voltage reference creates positive and
negative reference voltages that define the 1.2 V p-p fixed span
of the ADC core. This internal voltage reference can be adjusted
by means of SPI control. It can also be driven externally with
an off-chip stable reference. See the Memory Map Register
Descriptions section for more details.
RBIAS
The AD9284 requires the user to place a 10 kΩ resistor between
the RBIAS pin and ground. This resistor, which is used to set
the master current reference of the ADC core, should have a 1%
tolerance.
相關PDF資料 |
PDF描述 |
|---|---|
| UCS2W680MNY9 | CAP ALUM 68UF 450V 20% RADIAL |
| MAX11613EVSYS+ | EVALUATION SYSTEM FOR MAX11613 |
| MAX11046EVKIT+ | KIT EVALUATION FOR MAX11046 |
| AD9653-125EBZ | BOARD EVAL FOR AD9653 |
| CDB5532U | BOARD EVAL FOR CS5532U ADC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD9284BCPZ-250 | 功能描述:IC ADC 8BIT 250MSPS 1.8V 48LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 其它有關文件:TSA1204 View All Specifications 標準包裝:1 系列:- 位數:12 采樣率（每秒）:20M 數據接口:并聯 轉換器數目:2 功率耗散（最大）:155mW 電壓電源:模擬和數字 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-TQFP 供應商設備封裝:48-TQFP（7x7） 包裝:Digi-Reel® 輸入數目和類型:4 個單端，單極；2 個差分，單極 產品目錄頁面:1156 (CN2011-ZH PDF) 其它名稱:497-5435-6 |
| AD9284BCPZRL7-250 | 功能描述:IC ADC 8BIT 250MSPS 1.8V 48LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
| AD9286 | 制造商:AD 制造商全稱:Analog Devices 功能描述:8-Bit, 500 MSPS, 1.8 V Analog-to-Digital Converter (ADC) |
| AD9286-500EBZ | 功能描述:BOARD EVAL FOR AD9286-500 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件 |
| AD9286BCPZ-500 | 功能描述:IC ADC 8BIT SPI/SRL 500M 48LFSCP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 其它有關文件:TSA1204 View All Specifications 標準包裝:1 系列:- 位數:12 采樣率（每秒）:20M 數據接口:并聯 轉換器數目:2 功率耗散（最大）:155mW 電壓電源:模擬和數字 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-TQFP 供應商設備封裝:48-TQFP（7x7） 包裝:Digi-Reel® 輸入數目和類型:4 個單端，單極；2 個差分，單極 產品目錄頁面:1156 (CN2011-ZH PDF) 其它名稱:497-5435-6 |
發布緊急采購，3分鐘左右您將得到回復。