- 您現在的位置：買賣IC網 > PDF目錄9789 > AD9238BSTRL-40 (Analog Devices Inc)IC ADC 12BIT DUAL 40MSPS 64-LQFP PDF資料下載
參數資料
| 型號： | AD9238BSTRL-40 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 11/48頁 |
| 文件大小： | 0K |
| 描述： | IC ADC 12BIT DUAL 40MSPS 64-LQFP |
| 產品變化通告： | AD9238 Lead Discontinuation 12/Sept/2011 |
| 標準包裝： | 2,000 |
| 位數： | 12 |
| 采樣率（每秒）： | 40M |
| 數據接口： | 并聯(lián) |
| 轉換器數目： | 2 |
| 功率耗散（最大）： | 330mW |
| 電壓電源： | 單電源 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 64-LQFP |
| 供應商設備封裝： | 64-LQFP（7x7） |
| 包裝： | 帶卷 (TR) |
| 輸入數目和類型： | 4 個單端，單極；2 個差分，單極 |
| 配用： | AD9238BCP-65EBZ-ND - BOARD EVAL WITH AD9238BCP-65 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁
AD9238
Rev. C | Page 19 of 48
DATA FORMAT
The AD9238 data output format can be configured for either
twos complement or offset binary. This is controlled by the data
format select pin (DFS). Connecting DFS to AGND produces
offset binary output data. Conversely, connecting DFS to AVDD
formats the output data as twos complement.
The output data from the dual ADCs can be multiplexed onto a
single 12-bit output bus. The multiplexing is accomplished by
toggling the MUX_SELECT bit, which directs channel data to
the same or opposite channel data port. When MUX_SELECT
is logic high, the Channel A data is directed to the Channel A
output bus, and the Channel B data is directed to the Channel B
output bus. When MUX_SELECT is logic low, the channel data
is reversed, that is the Channel A data is directed to the
Channel B output bus, and the Channel B data is directed to the
Channel A output bus. By toggling the MUX_SELECT bit,
multiplexed data is available on either of the output data ports.
If the ADCs run with synchronized timing, this same clock can
be applied to the MUX_SELECT pin. Any skew between CLK_A,
CLK_B, and MUX_SELECT can degrade ac performance. It is
recommended to keep the clock skew <100 pS. After the
MUX_SELECT rising edge, either data port has the data for its
respective channel; after the falling edge, the alternate channel’s
data is placed on the bus. Typically, the other unused bus would
be disabled by setting the appropriate OEB high to reduce
power consumption and noise. Figure 34 shows an example of
multiplex mode. When multiplexing data, the data rate is two
times the sample rate. Note that both channels must remain
active in this mode and that each channel’s power-down pin
must remain low.
VOLTAGE REFERENCE
A stable and accurate 0.5 V voltage reference is built into the
AD9238. The input range can be adjusted by varying the reference
voltage applied to the AD9238, using either the internal
reference with different external resistor configurations or an
externally applied reference voltage. The input span of the ADC
tracks reference voltage changes linearly. If the ADC is being
driven differentially through a transformer, the reference voltage
can be used to bias the center tap (common-mode voltage).
The shared reference mode allows the user to connect the references
from the dual ADCs together externally for superior gain and
offset matching performance. If the ADCs are to function
independently, the reference decoupling can be treated
independently and can provide superior isolation between the dual
channels. To enable shared reference mode, the SHARED_REF
pin must be tied high and the external differential references
must be externally shorted. (REFT_A must be externally
shorted to REFT_B, and REFB_A must be shorted to REFB_B.)
Internal Reference Connection
A comparator within the AD9238 detects the potential at the
SENSE pin and configures the reference into four possible states,
which are summarized in Table 7. If SENSE is grounded, the
reference amplifier switch is connected to the internal resistor
divider (see Figure 35), setting VREF to 1 V. Connecting the
SENSE pin to VREF switches the reference amplifier output to
the SENSE pin, completing the loop and providing a 0.5 V
reference output. If a resistor divider is connected, as shown in
Figure 36, the switch is again set to the SENSE pin. This puts
the reference amplifier in a noninverting mode with the VREF
output defined as
VREF = 0.5 × (1 + R2/R1)
In all reference configurations, REFT and REFB drive the ADC
core and establish its input span. The input range of the ADC
always equals twice the voltage at the reference pin for either an
internal or an external reference.
VIN+
VIN–
10
μF
10
μF
0.1
μF
0.1
μF
REFT
ADC
CORE
SELECT
LOGIC
SENSE
0.1
μF
0.5V
AD9238
REFB
0.1
μF
VREF
02640-034
Figure 35. Internal Reference Configuration
Table 7. Reference Configuration Summary
Selected Mode
SENSE Voltage
Resulting VREF (V)
Resulting Differential Span (V p-p)
External Reference
AVDD
N/A
2 × External Reference
Internal Fixed Reference
VREF
0.5
1.0
Programmable Reference
0.2 V to VREF
0.5 × (1 + R2/R1)
2 × VREF (See Figure 36)
Internal Fixed Reference
AGND to 0.2 V
1.0
2.0
相關PDF資料 |
PDF描述 |
|---|---|
| MS27468T25B29PA | CONN RCPT 29POS JAM NUT W/PINS |
| AD9235BRURL7-65 | IC ADC 12BIT 65MSPS 28-TSSOP |
| MS27497E16F35PA | CONN RCPT 55POS WALL MNT W/PINS |
| MAX3222EUP/V+ | TXRX RS-232 ESD PROTECT 20TSSOP |
| MS27473P14F37P | CONN PLUG 37POS STRAIGHT W/PINS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD9238BSTRL-65 | 功能描述:IC ADC 12BIT DUAL 65MSPS 64-LQFP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 位數:12 采樣率（每秒）:3M 數據接口:- 轉換器數目:- 功率耗散（最大）:- 電壓電源:- 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-23-6 包裝:帶卷 (TR) 輸入數目和類型:- |
| AD9238BSTZ-20 | 功能描述:IC ADC 12BIT DUAL 20MSPS 64-LQFP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6 |
| AD9238BSTZ-20EB | 制造商:AD 制造商全稱:Analog Devices 功能描述:12-Bit, 20 MSPS/40 MSPS/65 MSPS Dual A/D Converter |
| AD9238BSTZ-40 | 功能描述:IC ADC 12BIT DUAL 40MSPS 64-LQFP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6 |
| AD9238BSTZ-40 | 制造商:Analog Devices 功能描述:IC 12-BIT ADC |
發(fā)布緊急采購，3分鐘左右您將得到回復。