參數資料
型號： AD9148BBCZ
廠商： Analog Devices Inc
文件頁數： 57/72頁
文件大小： 0K
描述： IC DAC 16BIT QD 1GSPS 196CSPBGA
標準包裝： 1
系列： TxDAC+®
設置時間： 20ns
位數： 16
數據接口： 串行，SPI?
轉換器數目： 4
電壓電源： 模擬和數字
功率耗散（最大）： 2.22W
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 196-LFBGA，CSPBGA
供應商設備封裝： 196-CSPBGA（12x12）
包裝： 托盤
輸出數目和類型： 8 電流，單極
采樣率（每秒）： *
AD9148
Data Sheet
Rev. B | Page 60 of 72
Transmit DAC Output Configurations
The optimum noise and distortion performance of the AD9148
is realized when it is configured for differential operation. The
common-mode error sources of the DAC outputs are reduced
significantly by the common-mode rejection of a transformer or
differential amplifier. These common-mode error sources include
even-order distortion products and noise. The enhancement in
distortion performance becomes more significant as the frequency
content of the reconstructed waveform increases and/or its
amplitude increases. This is due to the first-order cancellation
of various dynamic common-mode distortion mechanisms,
digital feedthrough, and noise.
IOUT1_P/IOUT3_P
IOUT1_N/IOUT3_N
IOUT2_N/IOUT4_N
IOUT2_P/IOUT4_P
RO
VIP +
VIN –
VOUTI
RO
VQP +
VQN –
VOUTQ
0
89
10
-0
76
Figure 78. Basic Transmit DAC Output Circuit
Figure 78 shows the most basic DAC output circuitry. A pair
of resistors, RO, are used to convert each of the complementary
output currents to a differential voltage output, VOUT. Because
the current outputs of the DAC are high impedance, the differential
driving point impedance of the DAC outputs, ROUT, is equal to
2 × RO. Figure 79 illustrates the output voltage waveforms.
VPEAK
VP
TIME
VN
VOM
VP
08
91
0-
077
Figure 79. Voltage Output Waveforms
The common-mode signal voltage, VCM, is calculated by
O
FS
CM
R
I
V
2
The peak output voltage, VPEAK, is calculated by
VPEAK = IFS × RO
With this circuit configuration, the single-ended peak voltage is
the same as the peak differential output voltage.
Transmit DAC Linear Output Signal Swing
The DAC outputs have a linear output compliance voltage range
of ±1 V that must be adhered to achieve optimum performance.
The linear output signal swing is dependent on the full-scale output
current, IOUTFS, and the common-mode level of the output.
AUXILIARY DAC OPERATION
The AD9148 has four 10-bit auxiliary DACs (AUX1, AUX2, AUX3,
and AUX4). The full-scale output current on these DACs is derived
from the 1.2 V band gap reference and external resistor. The gain
scale from the reference amplifier current, IREF, to the auxiliary
DAC reference current is 16.67 with the auxiliary DAC gain set
to full-scale. This gives a full-scale current of approximately 2 mA
for each auxiliary DAC.
The magnitude of the AUX1 DAC current is controlled via
Bits[1:0], Register 0x33 (MSBs) and Bits[7:0], Register 0x32 (LSBs)
when DAC SPI select = 0 (Bit 4, Register 0x00). The magnitude
of the AUX2 DAC current is controlled via Bits[1:0], Register 0x37
(MSBs) and Bits[7:0], Register 0x36 (LSBs) when DAC SPI select = 0
(Bit 4, Register 0x00). Likewise, the magnitudes of AUX3 DAC
current and AUX4 DAC current are controlled via Register 0x33 to
Register 0x32 and Register 0x37 to Register 0x36, respectively
when DAC SPI Select = 1 (Register 0x00, Bit[4]).
The auxiliary DAC structure is shown in Figure 80. There are
two output signals on each auxiliary DAC. One signal is P, and
the other is N. The auxiliary DAC outputs are not differential.
Only one side of the auxiliary DAC (P or N) is active at one
time. The inactive side goes into a high impedance state (100 kΩ).
Control of the P side and N side for the auxiliary DACs is via
Bit 7, Register 0x33 and Bit 7, Register 0x37 (DAC SPI select is 0
to control AUX1 and AUX2, and DAC SPI select is 1 to control
AUX3 and AUX4).
AUX_P
AUX_N
VB
AUXDAC
DIRECTION
(SOURCE/SINK)
AUXDAC[9:0]
0mA TO 2mA
(SOURCE)
0mA TO 2mA
(SINK)
AUXDAC
SIGN
(P/N)
08
91
0-
078
Figure 80. Auxiliary DAC Structure
相關PDF資料
PDF描述
D38999/26KJ61PN CONN PLUG 61POS STRAIGHT W/PINS
D38999/24KE8PN CONN RCPT 8POS JAM NUT W/PINS
MS27474E24F4S CONN RCPT 56POS JAM NUT W/SCKT
AD5380BSTZ-5 IC DAC 14BIT 12C 40CH 5V 100LQFP
VI-BW1-MV-F3 CONVERTER MOD DC/DC 12V 150W
相關代理商/技術參數
參數描述
AD9148BBCZRL 功能描述:IC DAC 16BIT QD 1GSPS 196CSPBGA RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:TxDAC+® 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1,000 系列:- 設置時間:1µs 位數:8 數據接口:串行 轉換器數目:8 電壓電源:雙 ± 功率耗散（最大）:941mW 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC W 包裝:帶卷 (TR) 輸出數目和類型:8 電壓，單極 采樣率（每秒）:*
AD9148BBPZ 功能描述:IC DAC 16BIT SPI/SRL 196BGA RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:TxDAC+® 標準包裝:1 系列:- 設置時間:4.5µs 位數:12 數據接口:串行，SPI? 轉換器數目:1 電壓電源:單電源 功率耗散（最大）:- 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:8-SOICN 包裝:剪切帶 (CT) 輸出數目和類型:1 電壓，單極；1 電壓，雙極 采樣率（每秒）:* 其它名稱:MCP4921T-E/SNCTMCP4921T-E/SNRCTMCP4921T-E/SNRCT-ND
AD9148BBPZRL 功能描述:IC DAC 16BIT SPI/SRL 196BGA RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:TxDAC+® 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1,000 系列:- 設置時間:1µs 位數:8 數據接口:串行 轉換器數目:8 電壓電源:雙 ± 功率耗散（最大）:941mW 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC W 包裝:帶卷 (TR) 輸出數目和類型:8 電壓，單極 采樣率（每秒）:*
AD9148BPCZ 制造商:AD 制造商全稱:Analog Devices 功能描述:Quad 16-Bit,1 GSPS, TxDAC+ Digital-to-Analog Converter
AD9148BPCZRL 制造商:AD 制造商全稱:Analog Devices 功能描述:Quad 16-Bit,1 GSPS, TxDAC+ Digital-to-Analog Converter
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*