- 您現在的位置：買賣IC網 > PDF目錄373956 > AD8802AN (ANALOG DEVICES INC) 12 Channel, 8-Bit TrimDACs with Power Shutdown PDF資料下載
參數資料
| 型號： | AD8802AN |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | DAC |
| 英文描述： | 12 Channel, 8-Bit TrimDACs with Power Shutdown |
| 中文描述： | 12, SERIAL INPUT LOADING, 0.6 us SETTLING TIME, 8-BIT DAC, PDIP20 |
| 封裝： | PLASTIC, DIP-20 |
| 文件頁數： | 13/16頁 |
| 文件大?。?/td> | 432K |
| 代理商： | AD8802AN |
AD8802/AD8804
REV. 0
–13–
*
LDAA
STAA
$0000
SDI1
Hi-byte data loaded from memory
SDI1 = data in location 0000H
*
* Enter Contents of SDI2 Data Register
*
LDAA
STAA
*
LDX
LDY
*
* Reset AD8802 to one-half scale (AD8804 does not have a Reset input)
*
BCLR
PORTC,Y $02
BSET
PORTC,Y $02
*
* Get AD8802/04 ready for data input
*
BCLR
PORTD,Y $02
*
TFRLP
LDAA
0,X
STAA
SPDR
*
WAIT
LDAA
SPSR
BPL
WAIT
*
INX
CPX
#SDI2+1
BNE
TFRLP
*
* Update AD8802 output
*
BSET
PORTD,Y $20
*
PULA
PULY
PULX
RTS
$0001
SDI2
Low-byte data loaded from memory
SDI2 = Data in location 0001H
#SDI1
#$1000
Stack pointer at 1st byte to send via SDI
Stack pointer at on-chip registers
Assert /RS
De-Assert /RS
Assert /CS
Get a byte to transfer for SPI
Write SDI data reg to start xfer
Loop to wait for SPIF
SPIF is the MSB of SPSR
Increment counter to next byte for xfer
Are we done yet
If not, xfer the second byte
Latch register & update AD8802
When done, restore registers X, Y & A
** Return to Main Program **
Listing 3. AD8802/AD8804 to MC68HC11 Interface Program Source Code
An Intelligent Temperature Control System—Interfacing the
8051
m
C with the AD8802/AD8804 and TMP14
Connecting the 80CL51
μ
C, or any modern microcontroller,
with the TMP14 and AD8802/AD8804 yields a powerful tem-
perature control tool, as shown in Figure 27. For example, the
80CL51
μ
C controls the TrimDACs allowing the user to auto-
matically set the temperature setpoints voltages of the TMP14
via computer or touch pad, while the TMP14 senses the tem-
perature and outputs four open-collector trip-points. Feeding
these trip-point outputs back to the 80CL51
μ
C allow it to sense
whether or not a setpoint has been exceeded. Additional
80CL51
μ
C port pins or TMP14 trip-point outputs may then
be used to change fan speed (i.e., high, medium, low, off), or
increase/decrease the power level to a heater. (Please refer to the
TMP14 data sheet for more applications information.)
The
CS
(Chip Select) on the AD8802/AD8804 makes applica-
tions that call for large temperature sensor arrays possible. In
addition, the 12 channels of the AD8802/AD8804 allow inde-
pendent setpoint control for all four trip-point outputs on up to
three TMP14 temperature sensors. For example, assume that
the 80CL51
μ
C has eight free port pins available after all user
interface lines, interrupts, and the serial port lines have been
assigned. The eight port pins may be used as chip selects, in
which case an array of eight AD8802/AD8804s controlling
twenty-four TMP14 sensors is possible.
The AD8802/AD8804 and TMP14 are also ideal choices for
low power applications. These devices have power shutdown
modes and operate on a single 5 Volt supply. When their shut-
down modes are activated current consumption is reduced to
less than 35
μ
A. However, at high operating frequencies
(12 MHz) the 80CL51 consumes far more energy (18 mA typ)
than the AD8802/AD8804 and TMP14 combined. Therefore,
to achieve a low power design the 80CL51 should operate at its
lowest possible frequency or be placed in its power-down mode
at the end of each instruction sequence.
To use the power-down mode of the 80CL51
μ
C set PCON.1
as the last instruction executed prior to going into the power-
down mode. If INT2 and INT9 are enabled, the 80CL51
μ
C
can be awakened from power-down mode with external inter-
rupts. As shown in Figure 28, the TLC555 outputs a pulse
every few seconds providing the interrupt to restart the 80CL51
μ
C which then samples the user input pins, the outputs of the
相關PDF資料 |
PDF描述 |
|---|---|
| AD8802AR | 12 Channel, 8-Bit TrimDACs with Power Shutdown |
| AD8802ARU | 12 Channel, 8-Bit TrimDACs with Power Shutdown |
| AD8804 | 12 Channel, 8-Bit TrimDACs with Power Shutdown(12通道,帶電源關斷8位D/A轉換器) |
| AD8842 | Precision, Quad, SPST Analog Switches |
| AD8842AN | Precision, Quad, SPST Analog Switches |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD8802ANZ | 功能描述:IC DAC 8BIT 12CH W/SD 20DIP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:TrimDAC® 標準包裝:2,400 系列:- 設置時間:- 位數:18 數據接口:串行 轉換器數目:3 電壓電源:模擬和數字 功率耗散（最大）:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:36-TFBGA 供應商設備封裝:36-TFBGA 包裝:帶卷 (TR) 輸出數目和類型:* 采樣率（每秒）:* |
| AD8802AR | 功能描述:IC DAC 8BIT 12CH W/SD 20-SOIC RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:TrimDAC® 標準包裝:47 系列:- 設置時間:2µs 位數:14 數據接口:并聯 轉換器數目:1 電壓電源:單電源 功率耗散（最大）:55µW 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:28-SSOP（0.209"，5.30mm 寬） 供應商設備封裝:28-SSOP 包裝:管件 輸出數目和類型:1 電流，單極；1 電流，雙極 采樣率（每秒）:* |
| AD8802AR-REEL | 制造商:Analog Devices 功能描述:DAC 12-CH R-2R 8-bit 20-Pin SOIC W T/R |
| AD8802ARU | 功能描述:IC DAC 8BIT 12CH W/SD 20-TSSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:TrimDAC® 標準包裝:47 系列:- 設置時間:2µs 位數:14 數據接口:并聯 轉換器數目:1 電壓電源:單電源 功率耗散（最大）:55µW 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:28-SSOP（0.209"，5.30mm 寬） 供應商設備封裝:28-SSOP 包裝:管件 輸出數目和類型:1 電流，單極；1 電流，雙極 采樣率（每秒）:* |
| AD8802ARU-REEL | 功能描述:IC DAC 8BIT 12CH W/SD 20-TSSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:TrimDAC® 產品培訓模塊:LTC263x 12-, 10-, and 8-Bit VOUT DAC Family 特色產品:LTC2636 - Octal 12-/10-/8-Bit SPI VOUT DACs with 10ppm/°C Reference 標準包裝:91 系列:- 設置時間:4µs 位數:10 數據接口:MICROWIRE?，串行，SPI? 轉換器數目:8 電壓電源:單電源 功率耗散（最大）:2.7mW 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:14-WFDFN 裸露焊盤 供應商設備封裝:14-DFN-EP（4x3） 包裝:管件 輸出數目和類型:8 電壓，單極 采樣率（每秒）:* |
發(fā)布緊急采購，3分鐘左右您將得到回復。