- 您現在的位置：買賣IC網 > PDF目錄2137 > AD847SQ (Analog Devices Inc)IC OPAMP GP 50MHZ LP 32MA 8CDIP PDF資料下載
參數資料
| 型號： | AD847SQ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 12/12頁 |
| 文件大小： | 0K |
| 描述： | IC OPAMP GP 50MHZ LP 32MA 8CDIP |
| 標準包裝： | 1 |
| 放大器類型： | 通用 |
| 電路數： | 1 |
| 轉換速率： | 300 V/µs |
| 增益帶寬積： | 50MHz |
| 電流 - 輸入偏壓： | 3.3µA |
| 電壓 - 輸入偏移： | 500µV |
| 電流 - 電源： | 5.3mA |
| 電流 - 輸出 / 通道： | 32mA |
| 電壓 - 電源，單路/雙路(±)： | ±4.5 V ~ 18 V |
| 工作溫度： | -55°C ~ 125°C |
| 安裝類型： | 通孔 |
| 封裝/外殼： | 8-CDIP（0.300"，7.62mm） |
| 供應商設備封裝： | 8-CERDIP |
| 包裝： | 管件 |
AD847
REV. F
–9–
OFFSET NULLING
The input offset voltage of the AD847 is very low for a high
speed op amp, but if additional nulling is required, the circuit
shown in Figure 21 can be used.
Figure 21. Offset Nulling
INPUT CONSIDERATIONS
An input resistor (RIN in Figure 20) is required in circuits where
the input to the AD847 will be subjected to transient or con-
tinuous overload voltages exceeding the
±6 V maximum differ-
ential limit. This resistor provides protection for the input
transistors by limiting the maximum current that can be forced
into their bases.
For high performance circuits it is recommended that a resistor
(RB in Figures 19 and 20) be used to reduce bias current errors
by matching the impedance at each input. The offset voltage er-
ror will be reduced by more than an order of magnitude.
THEORY OF OPERATION
The AD847 is fabricated on Analog Devices’ proprietary
complementary bipolar (CB) process which enables the con-
struction of pnp and npn transistors with similar fTs in the
600 MHz to 800 MHz region. The AD847 circuit (Figure 22)
includes an npn input stage followed by fast pnps in the folded
cascode intermediate gain stage. The CB pnps are also used in
the current amplifying output stage. The internal compensation
capacitance that makes the AD847 unity gain stable is provided
by the junction capacitances of transistors in the gain stage.
The capacitor, CF, in the output stage mitigates the effect of ca-
pacitive loads. At low frequencies and with low capacitive
loads, the gain from the compensation node to the output is
very close to unity. In this case CF is bootstrapped and does not
contribute to the compensation capacitance of the part. As the
capacitive load is increased, a pole is formed with the output
impedance of the output stage. This reduces the gain, and
therefore, CF is incompletely bootstrapped. Some fraction of CF
contributes to the compensation capacitance, and the unity gain
bandwidth falls. As the load capacitance is increased, the band-
width continues to fall, and the amplifier remains stable.
C F
–IN
+IN
NULL 1
NULL 8
OUTPUT
+VS
–VS
Figure 22. AD847 Simplified Schematic
GROUNDING AND BYPASSING
In designing practical circuits with the AD847, the user must
remember that whenever high frequencies are involved, some
special precautions are in order. Circuits must be built with
short interconnect leads. A large ground plane should be used
whenever possible to provide a low resistance, low inductance
circuit path, as well as minimizing the effects of high frequency
coupling. Sockets should be avoided because the increased
interlead capacitance can degrade bandwidth.
Feedback resistors should be of low enough value to assure that
the time constant formed with the capacitance at the amplifier
summing junction will not limit the amplifier performance.
Resistor values of less than 5 k
are recommended. If a larger
resistor must be used, a small (<10 pF) feedback capacitor in
parallel with the feedback resistor, RF, may be used to compen-
sate for the input capacitances and optimize the dynamic perfor-
mance of the amplifier.
Power supply leads should be bypassed to ground as close as
possible to the amplifier pins. Ceramic disc capacitors of
0.1
F are recommended.
相關PDF資料 |
PDF描述 |
|---|---|
| AD848SQ | IC OPAMP GP 175MHZ LP 32MA 8CDIP |
| AD8500AKSZ-R2 | IC OPAMP GP R-R CMOS 7KHZ SC70-5 |
| AD8502ARJZ-R2 | IC OPAMP GP CMOS 7KHZ SOT23-8 |
| AD8510BRZ-REEL7 | IC OPAMP JFET 8MHZ PREC LN 8SOIC |
| AD8515AKSZ-R2 | IC AMP GP R-R CMOS 5MHZ SC70-5 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD847SQ/883B | 制造商:Analog Devices 功能描述:OP Amp Single GP ±18V 8-Pin CDIP 制造商:Analog Devices 功能描述:OP AMP SGL GP 18V 8CDIP - Rail/Tube 制造商:Analog Devices 功能描述:IC AMP HIGH SPEED 制造商:Analog Devices Inc. 功能描述:Precision Amplifiers High Spd Low Pwr Monolithic 制造商:Analog Devices Inc. 功能描述:Precision Amplifiers LOW POWER HIGH SPEED AMP |
| AD847SQ883B | 制造商:AD 功能描述:* |
| AD848 | 制造商:AD 制造商全稱:Analog Devices 功能描述:High Speed, Low Power Monolithic Op Amp |
| AD8488KBCZ | 制造商:Analog Devices 功能描述:CHARGE INTEGRATOR AMPLIFIER 255-PIN CSBGA TRAY - Trays |
| AD848AQ | 功能描述:IC OPAMP GP 175MHZ LP 32MA 8CDIP RoHS:否 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:2,500 系列:Excalibur™ 放大器類型:J-FET 電路數:1 輸出類型:- 轉換速率:45 V/µs 增益帶寬積:10MHz -3db帶寬:- 電流 - 輸入偏壓:20pA 電壓 - 輸入偏移:490µV 電流 - 電源:1.7mA 電流 - 輸出 / 通道:48mA 電壓 - 電源，單路/雙路(±):4.5 V ~ 38 V，±2.25 V ~ 19 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:8-SOIC 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。