- 您現在的位置：買賣IC網 > PDF目錄6043 > AD8397ARDZ (Analog Devices Inc)IC OPAMP VF R-R DUAL LN 8SOIC PDF資料下載
參數資料
| 型號： | AD8397ARDZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 3/16頁 |
| 文件大小： | 0K |
| 描述： | IC OPAMP VF R-R DUAL LN 8SOIC |
| 標準包裝： | 98 |
| 放大器類型： | 電壓反饋 |
| 電路數： | 2 |
| 輸出類型： | 滿擺幅 |
| 轉換速率： | 53 V/µs |
| -3db帶寬： | 69MHz |
| 電流 - 輸入偏壓： | 200pA |
| 電壓 - 輸入偏移： | 1000µV |
| 電流 - 電源： | 11mA |
| 電流 - 輸出 / 通道： | 310mA |
| 電壓 - 電源，單路/雙路(±)： | 3 V ~ 24 V，±1.5 V ~ 12 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-SOIC（0.154"，3.90mm Width）裸露焊盤 |
| 供應商設備封裝： | 8-SOIC-EP |
| 包裝： | 管件 |
| 產品目錄頁面： | 770 (CN2011-ZH PDF) |
| 其它名稱： | Q2233101 |
第1頁第2頁當前第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁
AD8397
Rev. A | Page 11 of 16
APPLICATIONS INFORMATION
The AD8397 is a voltage feedback operational amplifier that
features an H-bridge input stage and common-emitter, rail-to-rail
output stage. The AD8397 can operate from a wide supply range,
±1.5 V to ±12 V. When driving light loads, the rail-to-rail output is
capable of swinging to within 0.2 V of either rail. The output can
also deliver high linear output current when driving heavy loads,
up to 310 mA into 32 Ω while maintaining 80 dBc SFDR. The
AD8397 is fabricated on Analog Devices proprietary XFCB-HV.
POWER SUPPLY AND DECOUPLING
The AD8397 can be powered with a good quality, well-regulated,
low noise supply from ±1.5 V to ±12 V. Pay careful attention to
decoupling the power supply. Use high quality capacitors with
low equivalent series resistance (ESR), such as multilayer
ceramic capacitors (MLCCs), to minimize the supply voltage
ripple and power dissipation. Locate a 0.1 μF MLCC decoupling
capacitor(s) no more than 1/8 inch away from the power supply
pin(s). A large tantalum 10 μF to 47 μF capacitor is recommended
to provide good decoupling for lower frequency signals and to
supply current for fast, large signal changes at the AD8397 outputs.
LAYOUT CONSIDERATIONS
As with all high speed applications, pay careful attention to
printed circuit board (PCB) layout to prevent associated board
parasitics from becoming problematic. The PCB should have a
low impedance return path (or ground) to the supply. Removing
the ground plane from all layers in the immediate area of the
amplifier helps to reduce stray capacitances. The signal routing
should be short and direct in order to minimize the parasitic
inductance and capacitance associated with these traces. Locate
termination resistors and loads as close as possible to their
respective inputs and outputs. Keep input traces as far apart as
possible from the output traces to minimize coupling (crosstalk)
though the board.
When the AD8397 is configured as a differential driver, as in
some line driving applications, provide a symmetrical layout to
the extent possible in order to maximize balanced performance.
When running differential signals over a long distance, the traces
on the PCB should be close together or any differential wiring
should be twisted together to minimize the area of the inductive
loop that is formed. This reduces the radiated energy and makes
the circuit less susceptible to RF interference. Adherence to
stripline design techniques for long signal traces (greater than
approximately 1 inch) is recommended.
UNITY-GAIN OUTPUT SWING
When operating the AD8397 in a unity-gain configuration,
the output does not swing to the rails and is constrained by
the H-bridge input. This can be seen by comparing the output
overdrive recovery in Figure 7 and the input overdrive recovery in
Figure 22. To avoid overdriving the input and to realize the full
swing afforded by the rail-to-rail output stage, use the amplifier
in a gain of two or greater.
05069-
028
INPUT
OUTPUT
7
–1
0
1
0
80
160
240
320
400
TIME (ns)
480
560
640
720
800
2
3
4
5
6
V
O
LTS
Figure 22. Unity-Gain Input Overdrive Recovery
相關PDF資料 |
PDF描述 |
|---|---|
| ADA4841-2YRZ | IC OPAMP VF R-R DUAL LP LN 8SOIC |
| AD8664ARZ | IC OPAMP GP R-R CMOS 4MHZ 14SOIC |
| AD8664ARUZ | IC OPAMP GP R-R CMOS LN 14TSSOP |
| OP492GSZ | IC OPAMP GP 4MHZ QUAD 14SOIC |
| OP285GSZ | IC OPAMP GP 9MHZ DUAL PREC 8SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD8397ARDZ-REEL | 功能描述:IC OPAMP VF R-R DUAL LN 8SOIC RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- 放大器類型:電流檢測 電路數:1 輸出類型:- 轉換速率:- 增益帶寬積:125kHz -3db帶寬:- 電流 - 輸入偏壓:- 電壓 - 輸入偏移:100µV 電流 - 電源:1.1µA 電流 - 輸出 / 通道:- 電壓 - 電源，單路/雙路(±):- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:4-WFBGA，CSPBGA 供應商設備封裝:4-UCSP（2x2） 包裝:剪切帶 (CT) 其它名稱:MAX9634WERS+TCT |
| AD8397ARDZREEL7 | 制造商:ANALOG 功能描述:NEW |
| AD8397ARDZ-REEL7 | 功能描述:IC OPAMP VF R-R DUAL LN 8SOIC RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:100 系列:- 放大器類型:通用 電路數:1 輸出類型:- 轉換速率:0.2 V/µs 增益帶寬積:- -3db帶寬:- 電流 - 輸入偏壓:100pA 電壓 - 輸入偏移:30µV 電流 - 電源:380µA 電流 - 輸出 / 通道:- 電壓 - 電源，單路/雙路(±):±2 V ~ 18 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:8-SO 包裝:管件 |
| AD8397AR-EBZ | 功能描述:BOARD EVAL FOR AD8397AR RoHS:是 類別:編程器，開發系統 >> 評估板 - 運算放大器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- |
| AD8397ARZ | 功能描述:IC OPAMP VF R-R DUAL LN 8SOIC RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:2,500 系列:- 放大器類型:通用 電路數:4 輸出類型:- 轉換速率:0.6 V/µs 增益帶寬積:1MHz -3db帶寬:- 電流 - 輸入偏壓:45nA 電壓 - 輸入偏移:2000µV 電流 - 電源:1.4mA 電流 - 輸出 / 通道:40mA 電壓 - 電源，單路/雙路(±):3 V ~ 32 V，±1.5 V ~ 16 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:14-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:14-TSSOP 包裝:帶卷 (TR) 其它名稱:LM324ADTBR2G-NDLM324ADTBR2GOSTR |
發布緊急采購，3分鐘左右您將得到回復。