- 您現在的位置：買賣IC網 > PDF目錄2137 > AD8235ACBZ-P7 (Analog Devices Inc)IC AMP INSTR RRIO 23KHZ 11WLCSP PDF資料下載
參數資料
| 型號： | AD8235ACBZ-P7 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 7/20頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC AMP INSTR RRIO 23KHZ 11WLCSP |
| 產品變化通告： | 8mm Carrier Tape Changes 28/Feb/2012 |
| 特色產品： | AD8235 Instrumentation Amplifier |
| 標準包裝： | 1 |
| 放大器類型： | 儀表 |
| 電路數： | 1 |
| 輸出類型： | 滿擺幅 |
| 轉換速率： | 0.011 V/µs |
| -3db帶寬： | 23kHz |
| 電流 - 輸入偏壓： | 1pA |
| 電壓 - 輸入偏移： | 2500µV |
| 電流 - 電源： | 30µA |
| 電流 - 輸出 / 通道： | 55mA |
| 電壓 - 電源，單路/雙路(±)： | 1.8 V ~ 5.5 V，±0.9 V ~ 2.75 V |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 11-WFBGA，WLCSP |
| 供應商設備封裝： | 11-WLCSP（1.57x2.04） |
| 包裝： | 標準包裝 |
| 產品目錄頁面： | 771 (CN2011-ZH PDF) |
| 其它名稱： | AD8235ACBZ-P7DKR |
AD8235
Rev. 0 | Page 15 of 20
TRACE
WIDTH
PAD OPENING
MASK OPENING
SHUTDOWN FEATURE
The AD8235 includes a shutdown pin (SDN) that further
enhances the flexibility and ease of use in portable applications
where power consumption is critical. A logic level signal can be
applied to this pin to switch to shutdown mode, even when the
supply is still on.
When connecting the SDN pin to +VS or applying a voltage
within +VS 0.5 V, the AD8235 operates in its normal condition
and, therefore, draws approximately 40 μA of supply current.
When connecting the SDN pin to VS, or any voltage within VS +
0.5 V, the AD8235 operates in shutdown mode and, therefore,
draws less than 500 nA of supply current, offering considerable
power savings.
0
82
11
-04
4
In cases where the AD8235 is operating in shutdown mode, if
a voltage potential exists at the REF pin, and there is a load to
VS at the output of the part, some additional current draw is
noticeable. In this mode, a path from the REF pin to VS exists,
leading to some additional current draw from the reference.
Typically, this current is negligible because the output of the
AD8235 is driving a high impedance node, such as the input of
an ADC.
LAYOUT RECOMMENDATIONS
The critical board design parameters, as it pertains to a WLCSP
package, are pad opening, pad type, pad finish, and board
thickness.
Pad Opening
Based on the IPC (Institute for Printed Circuits) standard, the
pad opening equals the UBM (Under Bump Metallurgy)
opening. The typical pad openings for the AD8235 shown in
Figure 37 are:
250 μm (0.5 mm pitch WLCSP)
The solder mask opening is 100 μm plus the pad opening (or
350 μm in the case of the AD8235). The trace width should be
less than two-thirds of the pad opening. Increasing the trace
width can cause reduction in the stand-off height of the solder
bump. Therefore, maintaining the proper trace width ratio is
important to ensure the reliability of the solder connections.
Figure 37. Pad Opening
Pad Type
For the actual board fabrication, the following types of
pads/land patterns are used for surface mount assembly:
Nonsolder mask defined (NSMD). The metal pad on the
PCB (to which the I/O is attached) is smaller than the
solder mask opening.
Solder mask defined (SMD). The solder mask opening is
smaller than the metal pad.
Because the copper etching process has tighter control than the
solder mask opening process, NSMD is preferred over SMD.
The solder mask opening on NSMD pads is larger than the
copper pads, allowing the solder to attach to the sides of the
copper pad and improving the reliability of the solder joints.
Pad Finish
The finish layer on the metal pads has a significant effect on
assembly yield and reliability. The typical metal pad finishes
used are organic surface preservative (OSP) and electroless
nickel immersion gold (ENIG). The thickness of the OSP finish
on a metal pad is 0.2 μm to 0.5 μm. This finish evaporates during
the reflow soldering process and interfacial reactions occur
between the solder and metal pad. The ENIG finish consists
of 5 μm of electroless nickel and 0.02 μm to 0.05 μm of gold.
During reflow soldering, the gold layer dissolves rapidly, followed
by reaction between the nickel and solder. It is extremely important
to keep the thickness of gold below 0.05 μm to prevent the
formation of brittle intermetallic compounds.
相關PDF資料 |
PDF描述 |
|---|---|
| AD823AARZ-R7 | IC OPAMP FET RR 17MHZ DUAL 8SOIC |
| AD823AR | IC OPAMP JFET R-R DUAL LN 8SOIC |
| AD824ARZ-14-3V-RL | IC OPAMP JFET R-R 2MHZ LP 14SOIC |
| AD8250ARMZ-RL | IC AMP INST ICMOS LDRIFT 10MSOP |
| AD8251ARMZ-RL | IC AMP INST ICMOS LDRIFT 10MSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD8236 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Low Noise, Low Gain Drift, G = 2000 Instrumentation Amplifier |
| AD8236ARMZ | 功能描述:IC AMP INSTR ADJ R-R 8MSOP RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:50 系列:- 放大器類型:通用 電路數:2 輸出類型:滿擺幅 轉換速率:1.8 V/µs 增益帶寬積:6.5MHz -3db帶寬:4.5MHz 電流 - 輸入偏壓:5nA 電壓 - 輸入偏移:100µV 電流 - 電源:65µA 電流 - 輸出 / 通道:35mA 電壓 - 電源，單路/雙路(±):1.8 V ~ 5.25 V，±0.9 V ~ 2.625 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:10-MSOP 包裝:管件 |
| AD8236ARMZ1 | 制造商:AD 制造商全稱:Analog Devices 功能描述:40 ??A Micropower Instrumentation Amplifier with Zero Crossover Distortion |
| AD8236ARMZ-R7 | 功能描述:IC AMP INSTR R-R 9KHZ LP 8MSOP RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 產品培訓模塊:Differential Circuit Design Techniques for Communication Applications 標準包裝:1 系列:- 放大器類型:RF/IF 差分 電路數:1 輸出類型:差分 轉換速率:9800 V/µs 增益帶寬積:- -3db帶寬:2.9GHz 電流 - 輸入偏壓:3µA 電壓 - 輸入偏移:- 電流 - 電源:40mA 電流 - 輸出 / 通道:- 電壓 - 電源，單路/雙路(±):3 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-VQFN 裸露焊盤，CSP 供應商設備封裝:16-LFCSP-VQ 包裝:剪切帶 (CT) 產品目錄頁面:551 (CN2011-ZH PDF) 其它名稱:ADL5561ACPZ-R7CT |
| AD8236ARMZ-R71 | 制造商:AD 制造商全稱:Analog Devices 功能描述:40 ??A Micropower Instrumentation Amplifier with Zero Crossover Distortion |
發布緊急采購，3分鐘左右您將得到回復。