- 您現在的位置：買賣IC網 > PDF目錄5917 > AD8231ACPZ-WP (Analog Devices Inc)IC AMP INST R-R 7MHZ 16LFCSP PDF資料下載
參數資料
| 型號： | AD8231ACPZ-WP |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 11/24頁 |
| 文件大小： | 0K |
| 描述： | IC AMP INST R-R 7MHZ 16LFCSP |
| 標準包裝： | 64 |
| 放大器類型： | 儀表 |
| 電路數： | 2 |
| 輸出類型： | 滿擺幅 |
| 轉換速率： | 1.1 V/µs |
| 增益帶寬積： | 7MHz |
| 電流 - 輸入偏壓： | 250pA |
| 電壓 - 輸入偏移： | 4µV |
| 電流 - 電源： | 4mA |
| 電流 - 輸出 / 通道： | 70mA |
| 電壓 - 電源，單路/雙路(±)： | 3 V ~ 6 V，±1.5 V ~ 3 V |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-VQFN 裸露焊盤，CSP |
| 供應商設備封裝： | 16-LFCSP-VQ EP（4x4） |
| 包裝： | 托盤 - 晶粒 |
| 配用： | AD8231-EVALZ-ND - BOARD EVAL FOR AD8231 |
AD8231
Rev. B | Page 19 of 24
LAYOUT
The AD8231 is a high precision device. To ensure optimum
performance at the PCB level, care must be taken in the design
of the board layout. The AD8231 pinout is arranged in a logical
manner to aid in this task.
Power Supplies
The AD8231 should be decoupled with a 0.1 μF bypass capacitor
between the two supplies. This capacitor should be placed as close
as possible to Pin 11 and Pin 12, either directly next to the pins or
beneath the pins on the backside of the board. The auto-zero
architecture of the AD8231 requires a low ac impedance between
the supplies. Long trace lengths to the bypass capacitor increase
this impedance, which results in a larger input offset voltage.
A stable dc voltage should be used to power the instrumentation
amplifier. Noise on the supply pins can adversely affect
performance.
Package Considerations
The AD8231 comes in a 4 mm × 4 mm LFCSP. Beware of
blindly copying the footprint from another 4 mm × 4 mm
LFCSP part; it cannot have the same thermal pad size and leads.
Refer to the Outline Dimensions section to verify that
the PCB symbol has the correct dimensions. Space between
the leads and thermal pad should be kept as wide as possible
for the best bias current performance.
Thermal Pad
The AD8231 4 mm × 4 mm LFCSP comes with a thermal pad.
This pad is connected internally to VS. The pad can either be
left unconnected or connected to the negative supply rail. For
high vibration applications, a landing is recommended.
Because the AD8231 dissipates little power, heat dissipation
is rarely an issue. If improved heat dissipation is desired (for
example, when ambient temperatures are near 125°C or when
driving heavy loads), connect the thermal pad to the negative
supply rail. For the best heat dissipation performance, the
negative supply rail should be a plane in the board. See the
Thermal Resistance section for thermal coefficients with and
without the pad soldered.
INPUT BIAS CURRENT RETURN PATH
The input bias current of the AD8231 must have a return path
to common. When the source, such as a thermocouple, cannot
provide a return current path, one should be created, as shown
in Figure 51.
THERMOCOUPLE
+VS
REF
–VS
AD8231
CAPACITIVELY COUPLED
+VS
REF
C
–VS
AD8231
TRANSFORMER
+VS
REF
–VS
AD8231
INCORRECT
CAPACITIVELY COUPLED
+VS
REF
C
R
C
–VS
AD8231
1
fHIGH-PASS = 2πRC
THERMOCOUPLE
+VS
REF
–VS
10M
AD8231
TRANSFORMER
+VS
REF
–VS
AD8231
CORRECT
0
65
86
-03
3
Figure 51. Creating an IBIAS Path
INPUT PROTECTION
All terminals of the AD8231 are protected against ESD. In
addition, the input structure allows for dc overload conditions
a diode drop above the positive supply and a diode drop below
the negative supply. Voltages beyond these limits cause the ESD
diodes to conduct and current to flow. If overvoltage events are
anticipated, an external resistor should be used in series with
each of the inputs to limit the current to below 10 mA. Currents
up to 100 mA can be sustained for a few seconds.
Note that if either input is brought below the negative supply
to the point where the ESD diode turns on, the AD8231 output
can phase-reverse.
相關PDF資料 |
PDF描述 |
|---|---|
| PEC33DAFN | CONN HEADER .100 DUAL STR 66POS |
| 69192-416HLF | BERGSTIK II DR STRAIGHT RET |
| 69192-416 | BERGSTIK II DR STRAIGHT RET |
| 69192-110HLF | BERGSTIK II DR STRAIGHT RET |
| AD825AR-16-REEL | IC OPAMP JFET GP 26MHZ 16SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD8231-EVALZ | 功能描述:BOARD EVAL FOR AD8231 RoHS:是 類別:編程器，開發系統 >> 評估板 - 運算放大器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- |
| AD8231TCPZ-EP-R7 | 功能描述:IC INSTR AMP PROGR ENH 16LFCSP RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:150 系列:- 放大器類型:音頻 電路數:2 輸出類型:- 轉換速率:5 V/µs 增益帶寬積:12MHz -3db帶寬:- 電流 - 輸入偏壓:100nA 電壓 - 輸入偏移:500µV 電流 - 電源:6mA 電流 - 輸出 / 通道:50mA 電壓 - 電源，單路/雙路(±):4 V ~ 32 V，±2 V ~ 16 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:8-TSSOP 包裝:管件 |
| AD8231WACPZ-RL | 功能描述:IC AMP INST RRO 2.7MHZ 16LFCSP RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:50 系列:LinCMOS™ 放大器類型:通用 電路數:4 輸出類型:- 轉換速率:0.05 V/µs 增益帶寬積:110kHz -3db帶寬:- 電流 - 輸入偏壓:0.7pA 電壓 - 輸入偏移:210µV 電流 - 電源:57µA 電流 - 輸出 / 通道:30mA 電壓 - 電源，單路/雙路(±):3 V ~ 16 V，±1.5 V ~ 8 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:14-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:14-SOIC 包裝:管件 產品目錄頁面:865 (CN2011-ZH PDF) 其它名稱:296-1834296-1834-5 |
| AD8232 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Single-Lead, Heart Rate Monitor Front End |
| AD8232ACPZ | 制造商:AD 制造商全稱:Analog Devices 功能描述:Single-Lead, Heart Rate Monitor Front End |
發布緊急采購，3分鐘左右您將得到回復。