參數資料
型號: AD8190ACPZ
廠商: ANALOG DEVICES INC
元件分類: 運動控制電子
英文描述: 2:1 HDMI/DVI Switch with Equalization
中文描述: 2-CHANNEL, AUDIO/VIDEO SWITCH, QCC56
封裝: 8 X 8 MM, LEAD FREE, MO-220VLLD-2, LFCSP-56
文件頁數: 15/24頁
文件大小: 650K
代理商: AD8190ACPZ
AD8190
Rev. 0 | Page 15 of 24
START
FIXED PART ADDR
REGISTER ADDR
FIXED PART ADDR
DATA
STOP
ACK
ADDR
ACK
R/W
ADDR
ACK
ACK
R/W
SR
1
2
3
4
5
6
7
8
9 10 11
12
13
I2C_SCL
GENERAL CASE
I2C_SDA
EXAMPLE
I2C_SDA
0
Figure 30. I
2
C Read Procedure
READ PROCEDURE
To read data from the AD8190 register set, an I
2
C master (such
as a microcontroller) needs to send the appropriate control
signals to the AD8190 slave device. The signals are controlled
by the I
2
C master unless otherwise specified. For a diagram of
the procedure, see Figure 30. The steps for a read procedure are
as follows:
1.
Send a start condition (while holding the I2C_SCL line
high, pull the I2C_SDA line low).
2.
Send the AD8190 part address (seven bits). The upper six
bits of the AD8190 part address are the static value
[100100] and the LSB is set by Input Pin I2C_ADDR. This
transfer should be MSB first.
3.
Send the write indicator bit (0).
4.
Wait for the AD8190 to acknowledge the request.
5.
Send the register address (eight bits) from which data is to
be read. This transfer should be MSB first.
6.
Wait for the AD8190 to acknowledge the request.
7.
Send a repeated start condition (Sr) by holding the
I2C_SCL line high and pulling the I2C_SDA line low.
8.
Resend the AD8190 part address (seven bits) from Step 2.
The upper six bits of the AD8190 part address compose the
static value [100100]. The LSB is set by Input Pin I2C_ADDR.
This transfer should be MSB first.
9.
Send the read indicator bit (1).
10.
Wait for the AD8190 to acknowledge the request.
11.
The AD8190 serially transfers the data (eight bits) held in
the register indicated by the address set in Step 5. This data
is sent MSB first.
12.
Acknowledge the data from the AD8190.
13.
Do one of the following:
a.
Send a stop condition (while holding the I2C_SCL
line high, pull the SDA line high) and release control
of the bus to end the transaction (shown in Figure 30).
b.
Send a repeated start condition (while holding the
I2C_SCL line high, pull the I2C_SDA line low) and
continue with Step 2 of the write procedure (see the
previous Write Procedure section) to perform a write.
c.
Send a repeated start condition (while holding the
I2C_SCL line high, pull the I2C_SDA line low) and
continue with Step 2 of this procedure to perform a
read from another address.
d.
Send a repeated start condition (while holding the
I2C_SCL line high, pull the I2C_SDA line low) and
continue with Step 8 of this procedure to perform a
read from the same address.
SWITCHING/UPDATE DELAY
There is a delay between when a user writes to the configura-
tion registers of the AD8190 and when that state change takes
physical effect. This update delay begins at the falling edge of
I2C_SCL for the last data bit transferred, as shown in Figure 29.
This update delay is register specific and the times are specified
in Table 1.
During a delay window, new values can be written to the
configuration registers but the AD8190 does not physically
update until the end of that register’s delay window. Writing
new values during the delay window does not reset the window;
new values supersede the previously written values. At the end
of the delay window, the AD8190 physically assumes the state
indicated by the last set of values written to the configuration
registers. If the configuration registers are written after the delay
window ends, the AD8190 immediately updates and a new
delay window begins.
相關PDF資料
PDF描述
AD8190ACPZ-R7 2:1 HDMI/DVI Switch with Equalization
AD8190-EVAL 2:1 HDMI/DVI Switch with Equalization
AD8200 High Common-Mode Voltage, Single Supply Difference Amplifier
AD8200CHIPS High Common-Mode Voltage, Single Supply Difference Amplifier
AD8200R ECONOLINE: REC2.2-S_DRW(Z)/H* - 2.2W DIP Package- 1kVDC Isolation- Regulated Output- 4.5-9V, 9-18V, 18-36V, 36-72V Wide Input Range 2 : 1- UL94V-0 Package Material- Continuous Short Circiut Protection- Cost Effective- 100% Burned In- Efficiency to 84%
相關代理商/技術參數
參數描述
AD8190ACPZ-R7 功能描述:IC SW HDMI/DVI 2:1 EQUAL 56LFCSP RoHS:是 類別:集成電路 (IC) >> 專用 IC 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- 類型:調幀器 應用:數據傳輸 安裝類型:表面貼裝 封裝/外殼:400-BBGA 供應商設備封裝:400-PBGA(27x27) 包裝:散裝
AD8190-EVAL 制造商:Analog Devices 功能描述:EVAL BD FOR AD8190 ,2:1 HDMI/DVI SWIT W/ EQUALIZATION - Bulk
AD8191 制造商:Analog Devices 功能描述:- Bulk
AD8191A 制造商:AD 制造商全稱:Analog Devices 功能描述:4:1 HDMI/DVI Switch with Equalization
AD8191AASTZ 功能描述:IC HDMI/DVI SWITCH 4:1 100LQFP RoHS:是 類別:集成電路 (IC) >> 接口 - 模擬開關,多路復用器,多路分解器 系列:- 其它有關文件:STG4159 View All Specifications 標準包裝:5,000 系列:- 功能:開關 電路:1 x SPDT 導通狀態電阻:300 毫歐 電壓電源:雙電源 電壓 - 電源,單路/雙路(±):±1.65 V ~ 4.8 V 電流 - 電源:50nA 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:7-WFBGA,F(xiàn)CBGA 供應商設備封裝:7-覆晶 包裝:帶卷 (TR)