- 您現在的位置：買賣IC網 > PDF目錄1892 > AD8153ACPZ-RL7 (Analog Devices Inc)IC SW MUX/DEMUX SGL BUFF 32LFCSP PDF資料下載
參數資料
| 型號： | AD8153ACPZ-RL7 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 7/24頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC SW MUX/DEMUX SGL BUFF 32LFCSP |
| 標準包裝： | 1 |
| 系列： | XStream™ |
| 應用： | 2:1 多路復用器/1:2 多路分配器 |
| 接口： | I²C |
| 電源電壓： | 3 V ~ 3.6 V |
| 封裝/外殼： | 32-VFQFN 裸露焊盤，CSP |
| 供應商設備封裝： | 32-LFCSP-EP（5x5） |
| 包裝： | 標準包裝 |
| 安裝類型： | 表面貼裝 |
| 產品目錄頁面： | 801 (CN2011-ZH PDF) |
| 配用： | AD8153-EVALZ-ND - BOARD EVALUATION FOR AD8153 |
| 其它名稱： | AD8153ACPZ-RL7DKR |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁
AD8153
Rev. 0 | Page 15 of 24
I2C SERIAL CONTROL INTERFACE
REGISTER SET
The AD8153 can be controlled in one of three modes: pin
mode, serial mode, and mixed mode. In pin mode, the AD8153
control is derived from the package pins, whereas in serial
mode a set of internal registers controls the AD8153. There is
also a mixed mode where switching is controlled via external
pins, and equalization and pre-emphasis are controlled via the
internal registers. The methods for writing data to and reading
data from the AD8153 are described in the I2C Data Write
section and the I2C Data Read section.
The mode is controlled via the MODE pin. To set the part in
pin mode, MODE should be driven low to VEE. When MODE
is driven high to VCC, the part is set to serial or mixed mode.
In pin mode, all controls are derived from the external pins. In
serial mode, each channel’s equalization and pre-emphasis are
controlled only through the registers, as described in Table 8.
Additionally, further functionality is available in serial mode as
each channel’s output can be enabled/disabled with the Output
Enable control bits, which is not possible in pin mode. To
change the switching in the AD8153 to serial mode, the mask
bits (Register 0x00) must be set to 1 by writing the value 0x1F to
this register, as explained in the following sections. Once all the
mask bits are set to 1, switching is controlled via the LB_A,
LB_B, LB_C, SEL, and BICAST bits in the register set.
In mixed mode, each channel’s equalization and pre-emphasis
are controlled through the registers as described above. The
switching, however, can be controlled using either the external
pins or the internal register set. The source of the control is
selected using the mask bits (Register 0x00). If a mask bit is set
to 0, the external pin acts as the source for that specific control.
If a mask bit is set to 1, the associated internal register acts as
the source for that specific control. As an example, if Register 0x00
were set to the value 0x0C, the SEL and LB_C controls would
come from the internal register set (Bit 0 of Register 0x04 and Bit
3 of Register 0x03, respectively), and the BICAST, LB_A, and
LB_B controls would come from the external pins.
GENERAL FUNCTIONALITY
The AD8153 register set is controlled through a 2-wire I2C
interface. The AD8153 acts only as an I2C slave device. Therefore,
the I2C bus in the system needs to include an I2C master to
configure the AD8153 and other I2C devices that may be on the
bus. When the MODE pin is set to a Logic 1, data transfers are
controlled through the use of the two I2C wires: the input clock
pin, SCL, and the bidirectional data pin, SDA.
The AD8153 I2C interface can be run in the standard (100 kHz)
and fast (400 kHz) modes. The SDA line only changes value
when the SCL pin is low with two exceptions. To indicate the
beginning or continuation of a transfer, the SDA pin is driven
low while the SCL pin is high, and to indicate the end of a
transfer, the SDA line is driven high while the SCL line is high.
Therefore, it is important to control the SCL clock to only
toggle when the SDA line is stable unless indicating a start,
repeated start, or stop condition.
Table 8. Register Map
Address
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Default
00000000
(0x00)
BICAST MASK
SEL MASK
LB_C MASK
LB_B MASK
LB_A MASK
00000000
(0x00)
00000001
(0x01)
OUTPUT DISABLE A
LB_A
EQ_A
PE_A [1]
PE_A [0]
00000000
(0x00)
00000010
(0x02)
OUTPUT DISABLE B
LB_B
EQ_B
PE_B [1]
PE_B [0]
00000000
(0x00)
00000011
(0x03)
OUTPUT DISABLE C
LB_C
EQ_C
PE_C [1]
PE_C [0]
00000000
(0x00)
0000100
(0x04)
BICAST
SEL
00000000
(0x00)
相關PDF資料 |
PDF描述 |
|---|---|
| AD8155ACPZ | IC MUX/DEMUX DUAL BUFFER 64LFCSP |
| AD8156ABCZ | IC SWITCH XPT 4X4 W/EQ 49CSPBGA |
| AD8158ACPZ | IC MUX/DEMUX QUAD 2X1 100LFCSP |
| AD8159ASVZ | IC MUX/DEMUX QUAD BUFF 100TQFP |
| AD8174ANZ | IC MUX SW W/AMP 250MHZ 14-DIP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD8153-EVALZ | 功能描述:BOARD EVALUATION FOR AD8153 RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:XStream™ 標準包裝:1 系列:PCI Express® (PCIe) 主要目的:接口，收發器，PCI Express 嵌入式:- 已用 IC / 零件:DS80PCI800 主要屬性:- 次要屬性:- 已供物品:板 |
| AD8153XCPZ | 制造商:Analog Devices 功能描述:SINGLE-LANE 3.2GBPS 2:1 MUX / 1:2 DEMUX SWITCH 32-PIN LFCSP - Bulk |
| AD8155 | 制造商:AD 制造商全稱:Analog Devices 功能描述:6.5 Gbps Dual Buffer Mux/Demux |
| AD8155ACPZ | 功能描述:IC MUX/DEMUX DUAL BUFFER 64LFCSP RoHS:是 類別:集成電路 (IC) >> 接口 - 模擬開關，多路復用器，多路分解器 系列:XStream™ 其它有關文件:STG4159 View All Specifications 標準包裝:5,000 系列:- 功能:開關 電路:1 x SPDT 導通狀態電阻:300 毫歐 電壓電源:雙電源 電壓 - 電源，單路/雙路(±):±1.65 V ~ 4.8 V 電流 - 電源:50nA 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:7-WFBGA，F(xiàn)CBGA 供應商設備封裝:7-覆晶 包裝:帶卷 (TR) |
| AD8155ACPZ-R7 | 功能描述:IC MUX/DEMUX DUAL BUFFER 64LFCSP RoHS:是 類別:集成電路 (IC) >> 接口 - 模擬開關，多路復用器，多路分解器 系列:XStream™ 其它有關文件:STG4159 View All Specifications 標準包裝:5,000 系列:- 功能:開關 電路:1 x SPDT 導通狀態電阻:300 毫歐 電壓電源:雙電源 電壓 - 電源，單路/雙路(±):±1.65 V ~ 4.8 V 電流 - 電源:50nA 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:7-WFBGA，F(xiàn)CBGA 供應商設備封裝:7-覆晶 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。