參數資料
型號: AD7993BRUZ-1
廠商: Analog Devices Inc
文件頁數: 17/32頁
文件大?。?/td> 0K
描述: IC ADC 10BIT 4CHAN I2C 16TSSOP
標準包裝: 96
位數: 10
采樣率(每秒): 188k
數據接口: I²C,串行
轉換器數目: 1
功率耗散(最大): 2.2mW
電壓電源: 單電源
工作溫度: -40°C ~ 125°C
安裝類型: 表面貼裝
封裝/外殼: 16-TSSOP(0.173",4.40mm 寬)
供應商設備封裝: 16-TSSOP
包裝: 管件
輸入數目和類型: 4 個單端,單極
AD7993/AD7994
Rev. 0 | Page 24 of 32
WRITING TO THE AD7993/AD7994
Depending on the register being written to, there are three
different writes for the AD7993/AD7994.
WRITING TO THE ADDRESS POINTER REGISTER
FOR A SUBSEQUENT READ
In order to read from a particular register, the address pointer
register must first contain the address of that register. If it does
not, the correct address must be written to the address pointer
register by performing a single-byte write operation, as shown
in Figure 26. The write operation consists of the serial bus
address followed by the address pointer byte. No data is
written to any of the data registers. A read operation may be
subsequently performed to read the register of interest.
WRITING A SINGLE BYTE OF DATA TO THE ALERT
STATUS REGISTER OR CYCLE REGISTER
The alert status register, configuration register and the cycle
register are 8-bit registers, so only one byte of data can be
written to each. Writing a single byte of data to one of these
registers consists of the serial bus write address, the chosen
data register address written to the address pointer register,
followed by the data byte written to the selected data register.
WRITING TWO BYTES OF DATA TO A LIMIT OR
HYSTERESIS REGISTER
Each of the four limit registers are 16-bit registers, so two bytes
of data are required to write a value to any one of them. Writing
two bytes of data to one of these registers consists of the serial
bus write address, the chosen limit register address written to
the address pointer register, followed by two data bytes written
to the selected data register. See Figure 28.
If the master is write addressing the AD7993/AD7994, it can
write to more than one register. After the first write operation
has completed for the first data register in the next byte, the
master writes to the address pointer byte to select the next data
register for a write operation. This eliminates the need to
readdress the device in order to write to another data register.
SDA
START BY
MASTER
ACK. BY
AD7993/AD7994
ACK. BY
AD7993/AD7994
STOP BY
MASTER
FRAME 1
SERIAL BUS ADDRESS BYTE
FRAME 2
ADDRESS POINTER REGISTER BYTE
19
1
9
C4
C3
C2
P2
P1
P0
A0
A1
A2
A3
0
SCL
1
C1
P3
03472-0-026
R/W
Figure 26. Writing to the Address Pointer Register to Select a Register for a Subsequent Read Operation
SDA
ACK. BY
AD7993/AD7994
11
9
C4
C3
C2
P2
P1
P0
R/W
A0
A1
A2
A3
0
SCL
1
C1
P3
91
9
D7
D6
D5
D2
D1
D0
D4
D3
FRAME 3
DATA BYTE
SCL (CONTINUED)
SDA (CONTINUED)
03472-0-027
START BY
MASTER
ACK. BY
AD7993/AD7994
ACK. BY
AD7993/AD7994
STOP BY
MASTER
FRAME 1
SERIAL BUS ADDRESS BYTE
FRAME 2
ADDRESS POINTER REGISTER BYTE
Figure 27. Single-Byte Write Sequence
相關PDF資料
PDF描述
VI-25Y-IU-F4 CONVERTER MOD DC/DC 3.3V 132W
LTC1199CS8#PBF IC ADC 10BIT 450KHZ W/SD 8-SOIC
LTC1199LCS8#PBF IC ADC 10BIT 210KHZ W/SD 8-SOIC
VI-25Y-IU-F3 CONVERTER MOD DC/DC 3.3V 132W
AD7278BRMZ IC ADC 8BIT 3MSPS HS LP 8MSOP
相關代理商/技術參數
參數描述
AD7993BRUZ-1REEL 功能描述:IC ADC 10BIT 4CHAN I2C 16TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:2,500 系列:- 位數:16 采樣率(每秒):15 數據接口:MICROWIRE?,串行,SPI? 轉換器數目:1 功率耗散(最大):480µW 電壓電源:單電源 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:38-WFQFN 裸露焊盤 供應商設備封裝:38-QFN(5x7) 包裝:帶卷 (TR) 輸入數目和類型:16 個單端,雙極;8 個差分,雙極 配用:DC1011A-C-ND - BOARD DELTA SIGMA ADC LTC2494
AD7993-X 制造商:AD 制造商全稱:Analog Devices 功能描述:4-Channel, 10- and 12-Bit ADCs with I2C Compatible Interface in 16-Lead TSSOP
AD7994 制造商:AD 制造商全稱:Analog Devices 功能描述:4-Channel, 12-/10-Bit ADCs with I2C Compatible Interface in 16-Lead TSSOP
AD7994-0 制造商:AD 制造商全稱:Analog Devices 功能描述:4-Channel, 10- and 12-Bit ADCs with I2C Compatible Interface in 16-Lead TSSOP
AD7994-1 制造商:AD 制造商全稱:Analog Devices 功能描述:4-Channel, 10- and 12-Bit ADCs with I2C Compatible Interface in 16-Lead TSSOP