參數資料
型號: AD7980ACPZ-RL
廠商: Analog Devices Inc
文件頁數: 16/28頁
文件大小: 0K
描述: IC ADC 16BIT 1MSPS SAR 10LFCSP
標準包裝: 5,000
系列: PulSAR®
位數: 16
采樣率(每秒): 1M
數據接口: DSP,MICROWIRE?,QSPI?,串行,SPI?
轉換器數目: 1
功率耗散(最大): 10mW
電壓電源: 單電源
工作溫度: -40°C ~ 125°C
安裝類型: 表面貼裝
封裝/外殼: 10-WFDFN 裸露焊盤,CSP
供應商設備封裝: 10-LFCSP-WD(3x3)
包裝: 帶卷 (TR)
輸入數目和類型: 1 個偽差分,單極
Data Sheet
AD7980
Rev. C | Page 23 of 28
APPLICATION HINTS
LAYOUT
The printed circuit board (PCB) that houses the AD7980
should be designed so that the analog and digital sections are
separated and confined to certain areas of the board. The pinout of
the AD7980, with all its analog signals on the left side and all its
digital signals on the right side, eases this task.
Avoid running digital lines under the device because these couple
noise onto the die, unless a ground plane under the AD7980 is
used as a shield. Fast switching signals, such as CNV or clocks,
should never run near analog signal paths. Crossover of digital
and analog signals should be avoided.
At least one ground plane should be used. It can be common or
split between the digital and analog section. In the latter case,
the planes should be joined underneath the AD7980s.
The AD7980 voltage reference input REF has a dynamic input
impedance and should be decoupled with minimal parasitic
inductances. This is done by placing the reference decoupling
ceramic capacitor close to, ideally right up against, the REF and
GND pins and connecting them with wide, low impedance traces.
Finally, the power supplies VDD and VIO of the AD7980
should be decoupled with ceramic capacitors, typically 100 nF,
placed close to the AD7980 and connected using short and wide
traces to provide low impedance paths and reduce the effect of
glitches on the power supply lines.
An example of a layout following these rules is shown in
EVALUATING THE PERFORMANCE OF THE AD7980
Other recommended layouts for the AD7980 are outlined
in the documentation of the evaluation board for the AD7980
(EVAL-AD7980SDZ). The evaluation board package includes
a fully assembled and tested evaluation board, documentation,
and software for controlling the board from a PC via the
EVAL-SDP-CB1Z.
06392-
028
AD7980
Figure 43. Example Layout of the AD7980 (Top Layer)
06392-
027
Figure 44. Example Layout of the AD7980 (Bottom Layer)
相關PDF資料
PDF描述
MS3106E28-4S CONN PLUG 9POS STRAIGHT W/SCKT
VI-BWY-MY CONVERTER MOD DC/DC 3.3V 33W
ADN4694EBRZ-RL7 IC TXRX MLVDS 100MBPS 8SOIC
AD7686BCPZRL IC ADC 16BIT 500KSPS 10-LFCSP
MS27499E20B16PB CONN RCPT 16POS BOX MNT W/PINS
相關代理商/技術參數
參數描述
AD7980ACPZ-RL7 功能描述:IC ADC 16BIT 1MSPS SAR 10LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:PulSAR® 標準包裝:1,000 系列:- 位數:12 采樣率(每秒):300k 數據接口:并聯 轉換器數目:1 功率耗散(最大):75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC(0.295",7.50mm 寬) 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端,單極;1 個單端,雙極
AD7980ARMZ 功能描述:ADC 16BIT 1MSPS LP 10-MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:PulSAR® 標準包裝:1 系列:- 位數:14 采樣率(每秒):83k 數據接口:串行,并聯 轉換器數目:1 功率耗散(最大):95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP(0.600",15.24mm) 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端,雙極
AD7980ARMZ 制造商:Analog Devices 功能描述:; Leaded Process Compatible:Yes; Peak Re
AD7980ARMZRL7 功能描述:ADC 16BIT 1MSPS 2.5LSB 10-MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:PulSAR® 標準包裝:1 系列:microPOWER™ 位數:8 采樣率(每秒):1M 數據接口:串行,SPI? 轉換器數目:1 功率耗散(最大):- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤(4x4) 包裝:Digi-Reel® 輸入數目和類型:8 個單端,單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6
AD7980ARMZ-RL7 制造商:Analog Devices 功能描述:- Tape and Reel