參數資料
型號: AD7939BSUZ
廠商: Analog Devices Inc
文件頁數: 19/36頁
文件大?。?/td> 0K
描述: IC ADC 10BIT 8CH PARALL 32TQFP
標準包裝: 1
位數: 10
采樣率(每秒): 1.5M
數據接口: 并聯
轉換器數目: 1
功率耗散(最大): 13.5mW
電壓電源: 單電源
工作溫度: -40°C ~ 85°C
安裝類型: 表面貼裝
封裝/外殼: 32-TQFP
供應商設備封裝: 32-TQFP(7x7)
包裝: 托盤
輸入數目和類型: 8 個單端,單極;4 個差分,單極;4 個偽差分,單極;7 偽差分,單極
配用: EVAL-AD7939CBZ-ND - BOARD EVALUATION FOR AD7939CBZ
AD7938/AD7939
Data Sheet
Rev. C | Page 26 of 36
Reading Data from the AD7938/AD7939
With the W/B pin tied logic high, the AD7938/AD7939
interface operates in word mode. In this case, a single read
operation from the device accesses the conversion data-word
on Pins DB0/DB2 to Pin DB11. The DB8/HBEN pin assumes
its DB8 function. With the W/B pin tied to logic low, the
AD7938/AD7939 interface operates in byte mode. In this case,
the DB8/HBEN pin assumes its HBEN function. Conversion
data from the AD7938/AD7939 must be accessed in two read
operations with eight bits of data provided on DB0 to DB7 for
each of the read operations. The HBEN pin determines whether
the read operation accesses the high byte or the low byte of the
12-bit or 10-bit word. For a low byte read, DB0 to DB7 provide
the eight LSBs of the 12-bit word. For 10-bit operation, the two
LSBs of the low byte are 0s, followed by six bits of conversion
data. For a high byte read, DB0 to DB3 provide the four MSBs
of the 12-bit or10-bit word. DB5 to DB7 of the high byte
provide the channel ID. Figure 36 shows the read cycle timing
diagram for a 12-bit or 10-bit transfer. When operating in word
mode, the HBEN input does not exist, and only the first read
operation is required to access data from the device. When
operating in byte mode, the two read cycles shown in Figure 37
are required to access the full data-word from the device.
The CS and RD signals are gated internally and the level is
triggered active low. In either word mode or byte mode, CS and
RD can be tied together because the timing specifications for t10
and t11 are 0 ns minimum. This means the bus is constantly
driven by the AD7938/AD7939.
The data is placed onto the data bus a time t13 after both CS and
RD go low. The RD rising edge can be used to latch data out of
the device. After a time, t14, the data lines become three-stated.
Alternatively, CS and RD can be tied permanently low and the
conversion data is valid and placed onto the data bus a time, t9,
before the falling edge of BUSY.
Note that if RD is pulsed during the conversion time, this
causes a degradation in linearity performance of approximately
0.25 LSB. Reading during conversion by way of tying CS and
RD low does not cause any degradation.
t11
t10
t13
t15
t16
t14
t12
t17
LOW BYTE
HIGH BYTE
DB0 TO DB7
HBEN/DB8
RD
CS
03715-
005
Figure 37. AD7938/AD7939 Parallel Interface—Read Cycle Timing for Byte Mode Operation (W/B = 0)
相關PDF資料
PDF描述
AD7822BRZ IC ADC 8BIT 1CH 2MSPS 20-SOIC
VE-J43-MW-F2 CONVERTER MOD DC/DC 24V 100W
AD7811YNZ IC ADC 10BIT 4CHAN SRL 16DIP
VI-2TJ-IW-F3 CONVERTER MOD DC/DC 36V 100W
VE-J42-MW-F4 CONVERTER MOD DC/DC 15V 100W
相關代理商/技術參數
參數描述
AD7939BSUZ-REEL7 功能描述:IC ADC 10BIT 8CH PARALL 32TQFP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率(每秒):45k 數據接口:串行 轉換器數目:2 功率耗散(最大):315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC(0.295",7.50mm 寬) 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端,單極
AD7940 制造商:AD 制造商全稱:Analog Devices 功能描述:3mW, 100kSPS, 14-Bit ADC in 6-Lead SOT-23
AD7940BRJ 制造商:Analog Devices 功能描述:100 KSPS, 14_BIT ADC SOT 23 PKG I.C. - Bulk
AD7940BRJ-R2 制造商:Analog Devices 功能描述:ADC Single SAR 100ksps 14-bit Serial 6-Pin SOT-23 T/R 制造商:Analog Devices 功能描述:ADC SGL SAR 100KSPS 14BIT SERL 6PIN SOT-23 - Tape and Reel
AD7940BRJ-REEL7 制造商:Rochester Electronics LLC 功能描述: 制造商:Analog Devices 功能描述: