參數資料
型號： AD7879WARUZ-RL7
廠商： Analog Devices Inc
文件頁數： 8/41頁
文件大小： 0K
描述： IC ADC 12BIT CTLR TOUCH 16TSSOP
標準包裝： 1,000
類型： 電阻
觸摸面板接口： 4 線
輸入數/鍵： 1 TSC
分辨率（位）： 12 b
評估套件： *
數據接口： 串行，SPI?
數據速率/采樣率 (SPS，BPS)： 105k
電壓基準： 內部
電源電壓： 1.6 V ~ 3.6 V
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 16-TSSOP（0.173"，4.40mm 寬）
供應商設備封裝： 16-TSSOP
包裝： 帶卷 (TR)
AD7879/AD7889
Rev. C | Page 15 of 40
TOUCH-PRESSURE MEASUREMENT
The pressure applied to the touch screen by a pen or finger can
also be measured with the AD7879/AD7889 using some simple
calculations. The contact resistance between the X and Y plates
is measured, providing a good indication of the size of the
depressed area and, therefore, the applied pressure. The area of
the spot that is touched is proportional to the size of the object
touching it. The size of this resistance (RTOUCH) can be calculated
using two different methods.
First Method
The first method requires the user to know the total resistance
of the X-plate tablet (RX). Three touch screen conversions are
required: measurement of the X position, XPOSITION (Y+ input);
measurement of the X+ input with the excitation voltage applied
to Y+ and X (Z1 measurement); and measurement of the Y
input with the excitation voltage applied to Y+ and X (Z2
measurement). These three measurements are illustrated in
The AD7879/AD7889 have two special ADC channel settings
that configure the X and Y switches for the Z1 and Z2 measure-
ments and store the results in the Z1 and Z2 result registers. The
Z1 measurement is selected by setting the CHNL ADD[2:0] bits
to 101 in Control Register 1 (Address 0x01); the result is stored
in the X+ (Z1) result register (Address 0x0A). The Z2 measurement
is selected by setting the CHNL ADD[2:0] bits to 100 in Control
Register 1 (Address 0x01); the result is stored in the Y (Z2)
result register (Address 0x0B).
The touch resistance (RTOUCH) can then be calculated using the
following equation:
RTOUCH = (RXPLATE) × (XPOSITION/4096) × [(Z2/Z1) 1]
(2)
07667-
026
Y–
Y+
X–
X+
TOUCH
RESISTANCE
MEASURE
Z1 POSITION
X–
X+
Y–
Y+
TOUCH
RESISTANCE
MEASURE
X POSITION
Y–
Y+
X–
X+
TOUCH
RESISTANCE
MEASURE
Z2 POSITION
Figure 26. Three Measurements Required for Touch Pressure
Second Method
The second method requires the user to know the resistance of
the X-plate and Y-plate tablets. Three touch screen conversions
are required: a measurement of the X position (XPOSITION), the
Y position (YPOSITION), and the Z1 position.
The following equation also calculates the touch resistance
(RTOUCH):
RTOUCH = RXPLATE × (XPOSITION/4096) × [(4096/Z1) 1]
RYPLATE × [1 (YPOSITION/4096)]
(3)
TEMPERATURE MEASUREMENT
A temperature measurement option called the single-conversion
method is available on the AD7879/AD7889. The conversion
method requires only a single measurement on ADC Channel
001. The results are stored in the temperature conversion result
register (Address 0x0D). The AD7879/AD7889 do not provide
an explicit output of the temperature reading; the system must
perform some external calculations. This method is based on
an on-chip diode measurement.
The acquisition time is fixed at 16 ms for temperature
measurement.
Conversion Method
The conversion method makes use of the fact that the tempera-
ture coefficient of a silicon diode is approximately 2.1 mV/°C.
However, this small change is superimposed on the diode forward
voltage, which can have a wide tolerance. Therefore, it is necessary
to calibrate by measuring the diode voltage at a known temperature
to provide a baseline from which the change in forward voltage
with temperature can be measured. This method provides a
resolution of approximately 0.3°C and a predicted accuracy
of ±2°C.
The temperature limit comparison is performed on the result
in the temperature conversion result register (Address 0x0D),
which is the measurement of the diode forward voltage. The
values programmed into the high and low limits should be
referenced to the calibrated diode forward voltage to make
accurate limit comparisons.
相關PDF資料
PDF描述
AD7879-1WARUZ-RL IC ADC 12BIT CTRLR TOUCH 16TSSOP
AD7879-1WACPZ-RL IC ADC 12BIT CTRLR TOUCH 16LFCSP
AD7879WARUZ-RL IC ADC 12BIT CTLR TOUCH 16TSSOP
AD7889-1ACBZ-RL7 IC ADC 12BIT CTRLR TOUCH 12WLCSP
AD7889ACBZ-RL IC ADC 12BIT CTRLR TOUCH 12WLCSP
相關代理商/技術參數
參數描述
AD7880BCHIPS 功能描述:12 Bit Analog to Digital Converter 2 Input 1 SAR Die 制造商:analog devices inc. 系列:- 包裝:管件 零件狀態:上次購買時間 位數:12 采樣率（每秒）:66k 輸入數:2 輸入類型:單端 數據接口:并聯 配置:S/H-ADC 無線電 - S/H:ADC:1:1 A/D 轉換器數:1 架構:SAR 參考類型:外部，電源 電壓 - 電源，模擬:5V 電壓 - 電源，數字:5V 特性:- 工作溫度:-40°C ~ 85°C 封裝/外殼:模具 供應商器件封裝:模具 標準包裝:1
AD7880BN 功能描述:IC ADC 12BIT MONO LP 24-DIP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極
AD7880BNZ 功能描述:IC ADC 12BIT MONO LOW PWR 24DIP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 其它有關文件:TSA1204 View All Specifications 標準包裝:1 系列:- 位數:12 采樣率（每秒）:20M 數據接口:并聯 轉換器數目:2 功率耗散（最大）:155mW 電壓電源:模擬和數字 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-TQFP 供應商設備封裝:48-TQFP（7x7） 包裝:Digi-Reel® 輸入數目和類型:4 個單端，單極；2 個差分，單極 產品目錄頁面:1156 (CN2011-ZH PDF) 其它名稱:497-5435-6
AD7880BQ 制造商:Analog Devices 功能描述:ADC Single SAR 66ksps 12-bit Parallel 24-Pin CDIP 制造商:Analog Devices 功能描述:ADC SGL SAR 66KSPS 12-BIT PARALLEL 24CDIP - Rail/Tube 制造商:Rochester Electronics LLC 功能描述:- Bulk
AD7880BR 功能描述:IC ADC 12BIT LC2MOS 5V LP 24SOIC RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*