- 您現在的位置：買賣IC網 > PDF目錄1984 > AD7877WACPZ-REEL7 (Analog Devices Inc)IC CTRLR TOUCH SCREEN 32LFCSP PDF資料下載
參數資料
| 型號： | AD7877WACPZ-REEL7 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 25/45頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC CTRLR TOUCH SCREEN 32LFCSP |
| 標準包裝： | 1 |
| 類型： | 電阻 |
| 觸摸面板接口： | 4 線 |
| 輸入數/鍵： | 1 TSC |
| 分辨率（位）： | 12 b |
| 評估套件： | 可供 |
| 數據接口： | 串行，SPI? |
| 數據速率/采樣率 (SPS，BPS)： | 125k |
| 電壓基準： | 外部，內部 |
| 電源電壓： | 2.7 V ~ 5.25 V |
| 電流 - 電源： | 1µA |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 32-VFQFN 裸露焊盤，CSP |
| 供應商設備封裝： | 32-LFCSP-VQ（5x5） |
| 包裝： | 標準包裝 |
| 其它名稱： | AD7877WACPZ-REEL7DKR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁當前第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁
AD7877
Data Sheet
Rev. D | Page 30 of 44
GENERAL-PURPOSE I/O PINS
The AD7877 has one dedicated general-purpose logic input/
output pin (GPIO4), and any or all of the three auxiliary analog
inputs can also be reconfigured as GPIOs. Associated with the
GPIOs are two 8-bit control registers and one 8-bit data register
that are accessed using the extended write mode.
As described in the Reading Data section, GPIO registers are
written to using the extended writing mode. The first four bits
of the data-word must be 1111b to access the extended writing
map, and the next four bits are the GPIO register address. This
leaves 8 bits for the GPIO register data, because all GPIO
registers are 8 bits.
The GPIO control registers are located at the 0000b and 0001b
extended writing map addresses, and the GPIO data register is
at Address 0010b. GPIO registers are read in the same way as
other registers, by writing a 5-bit address to Control Register 1.
The GPIO registers are located at Read Addresses 11011b to
Read Address 11101b.
GPIO CONFIGURATION
Each GPIO pin is configured by four bits in one of the GPIO
control registers and has a data bit in the GPIO data register.
The GPIO configuration bits are described in the following
sections and in Table 12. Also see the Detailed Register
Descriptions section.
Enable (EN)
These bits enable or disable the GPIO pins. When EN = 0, the
corresponding GPIO pin is configured as the alternate function
(AUX input). The other GPIO configuration bits have no effect,
if the particular GPIO is not enabled. When EN = 1, the pin is
configured as a GPIO pin. GPIO4, which does not have an
alternate function, does not have an EN bit; it is always enabled.
Direction—DIR
These bits set the direction of the GPIO pins. When DIR = 0,
the pin is an output. Setting or clearing the relevant bit in the
GPIO data register outputs a value on the corresponding GPIO
pin. The output value depends on the POL bit.
When DIR = 1, the pin is an input. An input value on the
relevant GPIO pin sets or clears the corresponding bit in the
GPIO data register, depending on the POL bit. A GPIO data
register bit is read-only when DIR = 1 for that GPIO.
Polarity (POL)
When POL = 0, the GPIO pin is active low. When POL = 1, the
GPIO pin is active high. How this bit affects the GPIO opera-
tion also depends on the DIR bit.
If POL = 1 and DIR = 1, a 1 at the input pin sets the corre-
sponding GPIO data register bit to 1. A 0 at the input pin clears
the corresponding GPIO data bit to 0.
If POL = 1 and DIR = 0, a 1 in the GPIO data register bit puts a
1 on the corresponding GPIO output pin. A 0 in the GPIO data
register bit puts a 0 on the GPIO output pin.
If POL = 0 and DIR = 1, a 1 at the input pin sets the corre-
sponding GPIO data bit to 0. A 0 at the input pin clears the
corresponding GPIO data bit to 1.
If POL = 0 and DIR = 0, a 1 in the GPIO data register bit puts a
0 on the corresponding GPIO output pin. A 0 in the GPIO data
register bit puts a 1 on the GPIO output pin.
ALERT Enable (ALEN)
GPIOs can operate as interrupt sources to trigger the ALERT
output. This is controlled by the ALERT enable (ALEN) bits in
the GPIO configuration registers. When ALEN = 1, the corre-
sponding GPIO can trigger an ALERT. When ALEN = 0, the
corresponding GPIO cannot cause the ALERT output to assert.
ALERT is asserted low if any GPIO data register bit is set when
the GPIO is configured as an input. The GPIO data bit is set if a
1 appears on the GPIO input pin when POL = 1, or if a 0
appears on the GPIO input pin when POL = 0. ALERT is
triggered only when the GPIO is configured as an input, that is,
when DIR = 1. ALERT can never be triggered by a GPIO that is
configured as an output, that is, DIR = 0.
ALERT Output
The ALERT pin is an alarm or interrupt output that goes low if
any one of a number of interrupt sources is asserted. The results
of high and low limit comparisons on the AUX1, BAT1, BAT2,
and TEMP1 channels are interrupt sources. An out-of-limit
comparison sets a status bit in the alert status/mask register
(Address 00011b).There are separate status bits for both the
high and low limits on each channel to indicate which limit was
exceeded. The interrupt sources can be masked out by clearing
the corresponding enable bit in this register. There is one enable
bit per channel.
ALERT is also asserted if an input on a GPIO pin sets a bit in
the GPIO data register, as explained in the ALERT Enable
(ALEN) section. GPIO interrupts can be disabled by clearing
the corresponding ALEN bit in the GPIO control registers.
The interrupt source can be identified by reading the GPIO data
register and the alert status/enable register. ALERT remains
asserted until the source of the interrupt has been masked out
or removed.
相關PDF資料 |
PDF描述 |
|---|---|
| AD7878KPZ | IC ADC 12BIT W/DSP INT 28-PLCC |
| AD7880CR | IC ADC 12BIT MONO LP 24-SOIC |
| AD7884BQ | IC ADC 16BIT SAMPLING HS 40-CDIP |
| AD7886JD | IC ADC 12BIT SAMPLING HS 28-CDIP |
| AD7887ARZ-REEL | IC ADC 12BIT 2CHAN SRL 8SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7878 | 制造商:AD 制造商全稱:Analog Devices 功能描述:LC2MOS Complete 12-Bit 100 kHz Sampling ADC with DSP Interface |
| AD7878AQ | 制造商:Rochester Electronics LLC 功能描述:COMPLETE 12 BIT ADC IC - Bulk |
| AD7878BQ | 功能描述:IC ADC 12BIT W/DSP INT 28-CDIP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:250 系列:- 位數:12 采樣率（每秒）:1.8M 數據接口:并聯 轉換器數目:1 功率耗散（最大）:1.82W 電壓電源:模擬和數字 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-LQFP 供應商設備封裝:48-LQFP（7x7） 包裝:管件 輸入數目和類型:2 個單端，單極 |
| AD7878JN | 制造商:Analog Devices 功能描述:ADC Single SAR 100ksps 12-bit Parallel 28-Pin PDIP W 制造商:Rochester Electronics LLC 功能描述:COMPLETE 12 BIT ADC IC - Bulk 制造商:Analog Devices 功能描述:LC2MOS Complete 12-Bit 100 kHz Sampling ADC with DSP Interface |
| AD7878JNZ | 功能描述:IC ADC 12BIT W/DSP INT 28-DIP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
發布緊急采購，3分鐘左右您將得到回復。