- 您現在的位置：買賣IC網 > PDF目錄375239 > AD7812YN (ANALOG DEVICES INC) +2.7 V to +5.5 V, 350 kSPS, 10-Bit 4-/8-Channel Sampling ADCs PDF資料下載
參數資料
| 型號： | AD7812YN |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | ADC |
| 英文描述： | +2.7 V to +5.5 V, 350 kSPS, 10-Bit 4-/8-Channel Sampling ADCs |
| 中文描述： | 8-CH 10-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDIP20 |
| 封裝： | 0.300 INCH, MINI, PLASTIC, DIP-20 |
| 文件頁數： | 16/19頁 |
| 文件大?。?/td> | 210K |
| 代理商： | AD7812YN |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁
AD7811/AD7812
–16–
REV. B
RFS. The first rising SCLK edge after the rising edge of the
RFS signal causes DOUT to leave its high impedance state and
data is clocked out onto the DOUT line and also on subsequent
SCLK rising edges. The DOUT pin goes back into a high
impedance state on the 11th SCLK rising edge—Point “A” on
Figure 18. A minimum of 11 SCLKs are therefore needed to
carry out a serial read. Data on the DIN line is latched in on
the first SCLK falling edge after the falling edge of the TFS
signal and on subsequent SCLK falling edges. The control
register is updated on the 13th SCLK rising edge—point “B” on
Figure 18. A minimum of 13 SCLK pulses are therefore needed
to complete a serial write operation. In multipackage applications
the RFS and TFS signals can be used as chip select signals. The
serial interface will not shift data in or out until it receives the
active edge of the RFS or TFS signal.
Simplifying the Serial Interface
The five-wire interface is designed to support many different
serial interface standards. However, it is possible to reduce the
number of lines required to just three. By simply connecting the
TFS and RFS pins to the
CONVST
signal (see Figure 4), the
CONVST
signal can be used to enable the serial port for read-
ing and writing. This is only possible where a noncontinuous
serial clock is being used.
MICROPROCESSOR INTERFACING
The serial interface on the AD7811 and AD7812 allows the
parts to be directly connected to a range of many different
microprocessors. This section explains how to interface the
AD7811 and AD7812 with some of the more common micro-
controller and DSP serial interface protocols.
AD7811/AD7812 to PIC16C6x/7x
The PIC16C6x Synchronous Serial Port (SSP) is configured as
an SPI Master with the Clock Polarity bit = 0. This is done
by writing to the Synchronous Serial Port Control Register
(SSPCON). See user
PIC16/17 Microcontroller User Manual
.
Figure 19 shows the hardware connections needed to interface
to the PIC16/17. In this example I/O port RA1 is being used to
pulse
CONVST
and enable the serial port of the AD7811/
AD7812. This microcontroller transfers only eight bits of data
during each serial transfer operation; therefore, two consecutive
read/write operations are needed.
CONVST
AD7811/AD7812
*
DOUT
DIN
SCLK
RFS
TFS
PIC16C6x/7x
*
SCK/RC3
SDO/RC5
SDI/ RC4
RA1
*
ADDITIONAL PINS OMITTED FOR CLARITY
Figure 19. Interfacing to the PIC16/17
AD7811/AD7812 to MC68HC11
The Serial Peripheral Interface (SPI) on the MC68HC11 is
configured for Master Mode (MSTR = 0), Clock Polarity Bit
(CPOL) = 0 and the Clock Phase Bit (CPHA) = 1. The SPI is
configured by writing to the SPI Control Register (SPCR)—see
68HC11 user manual. A connection diagram is shown in
Figure 20.
CONVST
AD7811/AD7812
*
DOUT
DIN
SCLK
RFS
TFS
MC68HC11
*
SCLK/PD4
MISO/PD2
MOSI/PD3
PA0
*
ADDITIONAL PINS OMITTED FOR CLARITY
Figure 20. Interfacing to the MC68HC11
AD7811/AD7812 to 8051
The AD7811/AD7812 requires a clock synchronized to the
serial data. The 8051 serial interface must therefore be operated
in Mode 0. In this mode serial data enters and exits through
RxD and a shift clock is output on TxD (half duplex). Figure 21
shows how the 8051 is connected to the AD7811/AD7812.
However, because the AD7811/AD7812 shifts data out on the
rising edge of the shift clock and latches data in on the falling
edge, the shift clock must be inverted.
AD7811/AD7812
*
DOUT
DIN
SCLK
TFS
8051
*
TxD
RxD
P1.1
*
ADDITIONAL PINS OMITTED FOR CLARITY
RFS
Figure 21. Interfacing to the 8051 Serial Port
相關PDF資料 |
PDF描述 |
|---|---|
| AD7812YR | 12-Bit, 4-Channel Parallel Output Sampling Analog-to-Digital Converter 28-SSOP |
| AD7812YRU | +2.7 V to +5.5 V, 350 kSPS, 10-Bit 4-/8-Channel Sampling ADCs |
| AD7811YRU | +2.7 V to +5.5 V, 350 kSPS, 10-Bit 4-/8-Channel Sampling ADCs |
| AD7811 | 350 kSPS, 10-Bit 4-/8-Channel Sampling ADCs(350kSPS四通道采樣A/D轉換器) |
| AD7812 | 350 kSPS, 10-Bit 4-/8-Channel Sampling ADCs(350kSPS八通道采樣A/D轉換器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7812YNZ | 功能描述:IC ADC 10BIT 8CHAN SRL 20DIP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 其它有關文件:TSA1204 View All Specifications 標準包裝:1 系列:- 位數:12 采樣率（每秒）:20M 數據接口:并聯 轉換器數目:2 功率耗散（最大）:155mW 電壓電源:模擬和數字 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-TQFP 供應商設備封裝:48-TQFP（7x7） 包裝:Digi-Reel® 輸入數目和類型:4 個單端，單極；2 個差分，單極 產品目錄頁面:1156 (CN2011-ZH PDF) 其它名稱:497-5435-6 |
| AD7812YR | 功能描述:IC ADC 10BIT 8-CHAN SRL 20-SOIC RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 位數:12 采樣率（每秒）:3M 數據接口:- 轉換器數目:- 功率耗散（最大）:- 電壓電源:- 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-23-6 包裝:帶卷 (TR) 輸入數目和類型:- |
| AD7812YR-REEL | 功能描述:IC ADC 10BIT 8-CHAN SRL 20-SOIC RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 位數:12 采樣率（每秒）:3M 數據接口:- 轉換器數目:- 功率耗散（最大）:- 電壓電源:- 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-23-6 包裝:帶卷 (TR) 輸入數目和類型:- |
| AD7812YR-REEL7 | 功能描述:IC ADC 10BIT 8-CHAN SRL 20-SOIC RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 位數:12 采樣率（每秒）:3M 數據接口:- 轉換器數目:- 功率耗散（最大）:- 電壓電源:- 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-23-6 包裝:帶卷 (TR) 輸入數目和類型:- |
| AD7812YRU | 制造商:Analog Devices 功能描述:ADC Single SAR 350ksps 10-bit Serial 20-Pin TSSOP 制造商:Analog Devices 功能描述:ADC SGL SAR 350KSPS 10-BIT SERL 20TSSOP - Rail/Tube 制造商:Rochester Electronics LLC 功能描述:8 CH. 10-BIT ADC I.C. - Bulk 制造商:Analog Devices 功能描述:IC 10-BIT ADC |
發布緊急采購，3分鐘左右您將得到回復。