- 您現在的位置：買賣IC網 > PDF目錄375239 > AD7811YR (ANALOG DEVICES INC) +2.7 V to +5.5 V, 350 kSPS, 10-Bit 4-/8-Channel Sampling ADCs PDF資料下載
參數資料
| 型號： | AD7811YR |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | ADC |
| 英文描述： | +2.7 V to +5.5 V, 350 kSPS, 10-Bit 4-/8-Channel Sampling ADCs |
| 中文描述： | 4-CH 10-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDSO16 |
| 封裝： | 0.150 INCH, SOIC-16 |
| 文件頁數： | 14/19頁 |
| 文件大?。?/td> | 210K |
| 代理商： | AD7811YR |
AD7811/AD7812
–14–
REV. B
DIN
DOUT
CONVST
V
DD
6040 HEX
NOT VALID
4040 HEX
VALID DATA
VALID DATA
4040 HEX
t
POWER-UP
1.5 s
t
CONVERT
2.3 s
t
CONVERT
2.3 s
Figure 15. Read/Write Sequence for AD7812
OPERATING MODES
The mode of operation of the AD7811 and AD7812 is selected
when the (logic) state of the
CONVST
is checked at the end of
a conversion. If the
CONVST
signal is logic high at the end
of a conversion, the part does not power down and is operat-
ing in Mode 1. If, however, the
CONVST
signal is brought
logic low before the end of a conversion, the AD7811 and AD7812
will power down at the end of the conversion. This is Mode 2
operation.
Mode 1 Operation (High Speed Sampling)
When the AD7811 and AD7812 are operated in Mode 1 they
are not powered down between conversions. This mode of opera-
tion allows high throughput rates to be achieved. The timing
diagram in Figure 16 shows how this optimum throughput rate
is achieved by bringing the
CONVST
signal high before the end
of the conversion.
The sampling circuitry leaves its tracking mode and goes into
hold on the falling edge of
CONVST
. A conversion is also initi-
ated at this time. The conversion takes 2.3
μ
s to complete. At
this point, the result of the current conversion is latched into the
serial shift register and the state of the
CONVST
signal checked.
The
CONVST
signal should be logic high at the end of the
conversion to prevent the part from powering down. The serial
port on the AD7811 and AD7812 is enabled on the rising edge
of the first SCLK after the rising edge of the RFS signal—see
Serial Interface section. As explained earlier, this rising edge
should occur before the end of the conversion process if the part
is not to be powered down. A serial read can take place at any
stage after the rising edge of
CONVST
. If a serial read is initi-
ated before the end of the current conversion process (i.e., at
time “A”), the result of the previous conversion is shifted out on
the DOUT pin. It is possible to allow the serial read to extend
beyond the end of a conversion. In this case the new data will
not be latched into the output shift register until the read
has finished. The dynamic performance of the AD7811 and
AD7812 typically degrades by up to 3 dBs while reading during
a conversion. If the user waits until the end of the conversion
process, i.e., 2.3
μ
s after the falling edge of
CONVST
(Point
“B”) before initiating a read, the current conversion result is
shifted out. The serial read must finish at least 100 ns prior to
the next falling edge of
CONVST
to allow the part to accurately
acquire the input signal.
Mode 2 Operation (Automatic Power-Down)
When used in this mode of operation the part automatically
powers down at the end of a conversion. This is achieved by
leaving the
CONVST
signal low until the end of the conversion.
Because it takes approximately 1.5
μ
s for the part to power-up
after it has been powered down, this mode of operation is intended
to be used in applications where slower throughput rates are
required, i.e., in the order of 250 kSPS and improved power
performance is required—see Power vs. Throughput section.
There are two power-down modes the AD7811/AD7812 can
CURRENT CONVERSION
RESULT
A
B
t
12
CONVST
DOUT
SCLK
t
1
t
2
Figure 16. Mode 1 Operation Timing Diagram
相關PDF資料 |
PDF描述 |
|---|---|
| AD7812YN | +2.7 V to +5.5 V, 350 kSPS, 10-Bit 4-/8-Channel Sampling ADCs |
| AD7812YR | 12-Bit, 4-Channel Parallel Output Sampling Analog-to-Digital Converter 28-SSOP |
| AD7812YRU | +2.7 V to +5.5 V, 350 kSPS, 10-Bit 4-/8-Channel Sampling ADCs |
| AD7811YRU | +2.7 V to +5.5 V, 350 kSPS, 10-Bit 4-/8-Channel Sampling ADCs |
| AD7811 | 350 kSPS, 10-Bit 4-/8-Channel Sampling ADCs(350kSPS四通道采樣A/D轉換器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7811YR-REEL | 制造商:Analog Devices 功能描述:ADC Single SAR 350ksps 10-bit Serial 16-Pin SOIC N T/R |
| AD7811YR-REEL7 | 制造商:Analog Devices 功能描述:ADC Single SAR 350ksps 10-bit Serial 16-Pin SOIC N T/R 制造商:Analog Devices 功能描述:ADC SGL SAR 350KSPS 10-BIT SERL 16SOIC N - Tape and Reel |
| AD7811YRU | 制造商:Analog Devices 功能描述:ADC Single SAR 350ksps 10-bit Serial 16-Pin TSSOP 制造商:Analog Devices 功能描述:ADC SGL SAR 350KSPS 10-BIT SERL 16TSSOP - Rail/Tube 制造商:Rochester Electronics LLC 功能描述:4 CH. 10-BIT ADC I.C. - Bulk |
| AD7811YRU-REEL | 制造商:Analog Devices 功能描述:ADC Single SAR 350ksps 10-bit Serial 16-Pin TSSOP T/R |
| AD7811YRU-REEL7 | 制造商:Analog Devices 功能描述:ADC Single SAR 350ksps 10-bit Serial 16-Pin TSSOP T/R 制造商:Analog Devices 功能描述:ADC SGL SAR 350KSPS 10-BIT SERL 16TSSOP - Tape and Reel |
發布緊急采購，3分鐘左右您將得到回復。