參數資料
型號： AD7811
廠商： Analog Devices, Inc.
英文描述： 350 kSPS, 10-Bit 4-/8-Channel Sampling ADCs(350kSPS四通道采樣A/D轉換器)
中文描述： 350 kSPS的，10位4-/8-Channel采樣ADC（350kSPS四通道采樣的A / D轉換器）
文件頁數： 14/20頁
文件大?。?/td> 215K
代理商： AD7811
AD7811/AD7812
–14–
REV. A
DIN
DOUT
CONVST
V
DD
6040 HEX
NOT VALID
4040 HEX
VALID DATA
VALID DATA
4040 HEX
t
POWER-UP
1
m
s
t
CONVERT
2.3
m
s
t
CONVERT
2.3
m
s
Figure 15. Read/Write Sequence for AD7812
OPERATING MODES
The mode of operation of the AD7811 and AD7812 is selected
when the (logic) state of the
CONVST
is checked at the end of
a conversion. If the
CONVST
signal is logic high at the end
of a conversion, the part does not power down and is operat-
ing in Mode 1. If, however, the
CONVST
signal is brought
logic low before the end of a conversion, the AD7811 and AD7812
will power down at the end of the conversion. This is Mode 2
operation.
Mode 1 Operation (High Speed Sampling)
When the AD7811 and AD7812 are operated in Mode 1 they
are not powered down between conversions. This mode of op-
eration allows high throughput rates to be achieved. The timing
diagram in Figure 16 shows how this optimum throughput rate
is achieved by bringing the
CONVST
signal high before the end
of the conversion.
The sampling circuitry leaves its tracking mode and goes into
hold on the falling edge of
CONVST
. A conversion is also initi-
ated at this time. The conversion takes 2.3
μ
s to complete. At
this point, the result of the current conversion is latched into the
serial shift register and the state of the
CONVST
signal checked.
The
CONVST
signal should be logic high at the end of the
conversion to prevent the part from powering down. The serial
port on the AD7811 and AD7812 is enabled on the rising edge
of the first SCLK after the rising edge of the RFS signal—see
Serial Interface section. As explained earlier, this rising edge
should occur before the end of the conversion process if the part
is not to be powered down. A serial read can take place at any
stage after the rising edge of
CONVST
. If a serial read is initi-
ated before the end of the current conversion process (i.e., at
time “A”), the result of the previous conversion is shifted out on
the DOUT pin. It is possible to allow the serial read to extend
beyond the end of a conversion. In this case the new data will
not be latched into the output shift register until the read
has finished. The dynamic performance of the AD7811 and
AD7812 typically degrades by up to 3 dBs while reading during
a conversion. If the user waits until the end of the conversion
process, i.e., 2.3
μ
s after the falling edge of
CONVST
(Point
“B”) before initiating a read, the current conversion result is
shifted out. The serial read must finish at least 100 ns prior to
the next falling edge of
CONVST
to allow the part to accurately
acquire the input signal.
Mode 2 Operation (Automatic Power-Down)
When used in this mode of operation the part automatically
powers down at the end of a conversion. This is achieved by
leaving the
CONVST
signal low until the end of the conversion.
Because it takes approximately 1
μ
s for the part to power-up
after it has been powered down, this mode of operation is in-
tended to be used in applications where slower throughput rates
are required, i.e., in the order of 250 kSPS and improved power
performance is required—see Power vs. Throughput section.
There are two power-down modes the AD7811/AD7812 can
CURRENT CONVERSION
RESULT
A
B
t
12
CONVST
DOUT
SCLK
t
1
t
2
Figure 16. Mode 1 Operation Timing Diagram
相關PDF資料
PDF描述
AD7812 350 kSPS, 10-Bit 4-/8-Channel Sampling ADCs(350kSPS八通道采樣A/D轉換器)
AD7813 8-/10-Bit Sampling ADC(400kSPS,8位/10位采樣A/D轉換器)
AD7814ARM 10-Bit Digital Temperature Sensor in 6-Lead SOT-23
AD7814ART 10-Bit Digital Temperature Sensor in 6-Lead SOT-23
AD7814 10-Bit Digital Temperature Sensor in 6-Lead SOT-23(10位數字溫度傳感器)
相關代理商/技術參數
參數描述
AD7811YN 制造商:Analog Devices 功能描述:ADC Single SAR 350ksps 10-bit Serial 16-Pin PDIP 制造商:Rochester Electronics LLC 功能描述:4 CH. 10-BIT ADC I.C. - Bulk 制造商:Analog Devices 功能描述:IC 10BIT ADC 4CH 7811 DIP16
AD7811YNZ 功能描述:IC ADC 10BIT 4CHAN SRL 16DIP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 其它有關文件:TSA1204 View All Specifications 標準包裝:1 系列:- 位數:12 采樣率（每秒）:20M 數據接口:并聯 轉換器數目:2 功率耗散（最大）:155mW 電壓電源:模擬和數字 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-TQFP 供應商設備封裝:48-TQFP（7x7） 包裝:Digi-Reel® 輸入數目和類型:4 個單端，單極；2 個差分，單極 產品目錄頁面:1156 (CN2011-ZH PDF) 其它名稱:497-5435-6
AD7811YR 制造商:Analog Devices 功能描述:ADC Single SAR 350ksps 10-bit Serial 16-Pin SOIC N 制造商:Analog Devices 功能描述:A/D Converter (A-D) IC
AD7811YR-REEL 制造商:Analog Devices 功能描述:ADC Single SAR 350ksps 10-bit Serial 16-Pin SOIC N T/R
AD7811YR-REEL7 制造商:Analog Devices 功能描述:ADC Single SAR 350ksps 10-bit Serial 16-Pin SOIC N T/R 制造商:Analog Devices 功能描述:ADC SGL SAR 350KSPS 10-BIT SERL 16SOIC N - Tape and Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*