參數資料
| 型號： | AD7789BRM |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 9/20頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 24BIT LP 10-MSOP |
| 標準包裝： | 50 |
| 位數： | 24 |
| 采樣率（每秒）： | 16.6 |
| 數據接口： | DSP，MICROWIRE?，QSPI?，串行，SPI? |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 230µW |
| 電壓電源： | 單電源 |
| 工作溫度： | -40°C ~ 105°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 10-TFSOP，10-MSOP（0.118"，3.00mm 寬） |
| 供應商設備封裝： | 10-MSOP |
| 包裝： | 管件 |
| 輸入數目和類型： | 1 個差分，單極；1 個差分，雙極 |
AD7788/AD7789
Rev. B | Page 17 of 20
CIRCUIT DESCRIPTION
ANALOG INPUT CHANNEL
The AD7788/AD7789 have one differential analog input
channel that is connected to the modulator, thus, the input is
unbuffered. Note that this unbuffered input path provides a
dynamic load to the driving source. Therefore,
resistor/capacitor combinations on the input pins can cause dc
gain errors, depending on the output impedance of the source
that is driving the ADC input. Table 13 shows the allowable
external resistance/capacitance values such that no gain error at
the 16-bit level is introduced (AD7788). Table 14 shows the
allowable external resistance/capacitance values such that no
gain error at the 20-bit level is introduced (AD7789).
Table 13. External R-C Combination for No 16-Bit Gain
Error (AD7788)
C (pF)
R (Ω)
50
22.8 k
100
13.1 k
500
3.3 k
1000
1.8 k
5000
360
Table 14. External R-C Combination for No 20-Bit Gain
Error (AD7789)
C (pF)
R (Ω)
50
16.7 k
100
9.6 k
500
2.2 k
1000
1.1 k
5000
160
The absolute input voltage includes the range between GND
30 mV and VDD + 30 mV. The negative absolute input voltage
limit does allow the possibility of monitoring small true bipolar
signals with respect to GND.
BIPOLAR/UNIPOLAR CONFIGURATION
The analog input to the devices can accept either unipolar or
bipolar input voltage ranges. A bipolar input range does not
imply that the parts can tolerate large negative voltages with
respect to system GND. Unipolar and bipolar signals on the
AIN(+) input are referenced to the voltage on the AIN() input.
For example, if AIN() is 2.5 V and the ADC is configured for
unipolar mode, the input voltage range on the AIN(+) pin is
2.5 V to 5 V. If the ADC is configured for bipolar mode, the
analog input range on the AIN(+) input is 0 V to 5 V. The
bipolar/unipolar option is chosen by programming the U/B bit
in the mode register.
DATA OUTPUT CODING
When the ADC is configured for unipolar operation, the output
code is natural (straight) binary with a zero differential input
voltage resulting in a code of 000...000, a midscale voltage
resulting in a code of 100...000, and a full-scale input voltage
resulting in a code of 111...111. The output code for any analog
input voltage can be represented as
Code = 2N × (AIN/VREF)
When the ADC is configured for bipolar operation, the output
code is offset binary with a negative full-scale voltage resulting
in a code of 000...000, a zero differential input voltage resulting
in a code of 100...000, and a positive full-scale input voltage
resulting in a code of 111...111. The output code for any analog
input voltage can be represented as
Code = 2N – 1 × [(AIN/VREF) + 1]
where:
AIN is the analog input voltage.
N = 16 for the AD7788, 24 for the AD7789.
REFERENCE INPUT
The AD7788/AD7789 have a fully differential input capability
for the channel. The common-mode range for these differential
inputs is from GND to VDD. The reference input is unbuffered
and, therefore, excessive R-C source impedances introduce gain
errors. The reference voltage REFIN [REFIN(+) REFIN()] is
2.5 V nominal, but the AD7788/AD7789 are functional with
reference voltages from 0.1 V to VDD. In applications where the
excitation (voltage or current) for the transducer on the analog
input also drives the reference voltage for the parts, the effect of
the low frequency noise in the excitation source is removed
because the application is ratiometric. If the AD7788/AD7789
are used in a nonratiometric application, a low noise reference
should be used.
Recommended 2.5 V reference voltage sources for the AD7788/
AD7789 include the ADR381 and ADR391, because they are
low noise, low power references. If the analog circuitry uses a
2.5 V power supply, the reference voltage source requires some
headroom. In this case, a 2.048 V reference such as the ADR380
or ADR390 can be used. Again, these are low power, low noise
references. Also note that the reference inputs provide a high
impedance, dynamic load. Because the input impedance of each
reference input is dynamic, resistor/capacitor combinations on
these inputs can cause dc gain errors, depending on the output
impedance of the source that is driving the reference inputs.
相關PDF資料 |
PDF描述 |
|---|---|
| AD7790BRM | IC ADC 16BIT BUFFERED LP 10MSOP |
| AD7791BRM | IC ADC 24BIT BUFFERED LP 10MSOP |
| AD7793BRU | IC ADC 24BIT 3CH LP 16-TSSOP |
| AD7794BRU | IC ADC 24BIT 6CH LP 24-TSSOP |
| AD7797BRUZ-REEL | IC ADC 24BIT SIG-DEL 1CH 16TSSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7789BRM-REEL | 功能描述:IC ADC 24BIT SIGMA-DELTA 10-MSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
| AD7789BRMZ | 功能描述:IC ADC 24BIT LP 10-MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6 |
| AD7789BRMZ-REEL | 功能描述:IC ADC 24BIT SIGMA-DELTA 10MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:2,500 系列:- 位數:16 采樣率（每秒）:15 數據接口:MICROWIRE?，串行，SPI? 轉換器數目:1 功率耗散（最大）:480µW 電壓電源:單電源 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:38-WFQFN 裸露焊盤 供應商設備封裝:38-QFN（5x7） 包裝:帶卷 (TR) 輸入數目和類型:16 個單端，雙極；8 個差分，雙極 配用:DC1011A-C-ND - BOARD DELTA SIGMA ADC LTC2494 |
| AD779 | 制造商:AD 制造商全稱:Analog Devices 功能描述:14-Bit 128 kSPS Complete Sampling ADC |
| AD7790 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Low Power, 16-Bit Buffered Sigma-Delta ADC |
發(fā)布緊急采購，3分鐘左右您將得到回復。