- 您現在的位置：買賣IC網 > PDF目錄1983 > AD7780BRZ-REEL (Analog Devices Inc)IC ADC 24BIT 1CH LP SD 14SOIC PDF資料下載
參數資料
| 型號： | AD7780BRZ-REEL |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 6/16頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 24BIT 1CH LP SD 14SOIC |
| 設計資源： | Weigh Scale Design Using AD7780 with Internal PGA (CN0107) |
| 標準包裝： | 2,500 |
| 位數： | 24 |
| 采樣率（每秒）： | 16.7 |
| 數據接口： | 串行，SPI? |
| 轉換器數目： | 1 |
| 電壓電源： | 模擬和數字 |
| 工作溫度： | -40°C ~ 105°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 14-SOIC（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 14-SO |
| 包裝： | 帶卷 (TR) |
| 輸入數目和類型： | 1 個差分，雙極 |
AD7780
Rev. A | Page 14 of 16
APPLICATIONS INFORMATION
The AD7780 provides a low cost, high resolution analog-to-digital
function. Because the analog-to-digital function is provided by a
Σ-Δ architecture, the parts are more immune to noisy environ-
ments, making them ideal for use in sensor measurement and
industrial and process control applications.
WEIGH SCALES
Figure 23 shows the AD7780 being used in a weigh scale
application. The load cell is arranged in a bridge network and
gives a differential output voltage between its OUT+ and OUT
terminals. Assuming a 5 V excitation voltage, the full-scale
output range from the transducer is 10 mV when the sensitivity
is 2 mV/V. The excitation voltage for the bridge can be used to
directly provide the reference for the ADC because the refer-
ence input range includes the supply voltage.
A second advantage of using the AD7780 in transducer-based
applications is that the bridge power-down switch (BPDSW)
can be fully utilized in low power applications. The bridge power-
down switch is connected in series with the low side of the bridge.
In normal operation, the switch is closed and measurements
can be taken. In applications where power is of concern, the
AD7780 can be placed in power-down mode, significantly
reducing the power consumed in the application. In addition,
the bridge power-down switch is opened while in power-down
mode, thus avoiding unnecessary power consumption by the
front-end transducer. When the part is taken out of power-down
mode and the bridge power-down switch is closed, the user should
ensure that the front-end circuitry is fully settled before attempting
a read from the AD7780.
The load cell has an offset or tare associated with it. This tare is
the main component of the system offset (load cell + ADC) and is
similar in magnitude to the full-scale signal from the load cell.
For this reason, calibrating the offset and gain of the AD7780 alone
is not sufficient for optimum accuracy; a system calibration that
calibrates the offset and gain of the ADC, plus the load cell, is
required. A microprocessor can be used to perform the calibra-
tions. The offset (the conversion result from the AD7780 when
no load is applied to the load cell) and the full-scale error (the
conversion result from the ADC when the maximum load is
applied to the load cell) must be determined. Subsequent conver-
sions from the AD7780 are then corrected, using the offset and
gain coefficients that were calculated from these calibrations.
PERFORMANCE IN A WEIGH SCALE SYSTEM
If the load cell has a sensitivity of 2 mV/V and a 5 V excitation
voltage is used, the full-scale signal from the load cell is 10 mV.
When the AD7780 operates with a 10 Hz output data rate and
the gain is set to 128, the device has a p-p resolution of 18.2 bits
when the reference is equal to 5 V. Postprocessing the data from
the AD7780 using a microprocessor increases the p-p resolution.
For example, an average by 4 in the microprocessor increases
the accuracy by 2 bits. The noise-free counts is equal to the
following:
Noise-Free Counts = (2Effective Bits)(FSLC/FSADC)
where:
Effective Bits = 18.2 bits + 2 bits (due to post-processing in the
microprocessor).
FSLC is the full-scale signal from the load cell (10 mV).
FSADC is the full-scale input range when gain = 128 and VREF = 5 V
(78 mV).
The noise-free counts are equal to the following:
(218.2 + 2)(10 mV/78 mV) = 154,422
This example shows that with a 5 V supply, 154,422 noise-free
counts can be achieved with the AD7780.
EMI RECOMMENDATIONS
For simplicity, the EMI filters are not included in Figure 23.
However, an R-C antialiasing filter should be included on each
analog input. This filter is needed because the on-chip digital
filter does not provide any rejection around the master clock or
multiples of the master clock. Suitable values are a 1 kΩ resistor
in series with each analog input, a 0.1 μF capacitor from AIN(+)
to AIN(), and 0.01 μF capacitors from AIN(+)/AIN() to GND.
G = 1
OR 128
24-BIT Σ-Δ
ADC
DOUT/RDY
GND
AVDD
AIN(+)
REFIN(+)
AIN(–)
SCLK
DVDD
FILTER
GAIN
INTERNAL
CLOCK
AD7780
PDRST
BPDSW
REFIN(–)
VDD
OUT–
IN+
IN–
OUT+
0
79
45
-02
2
Figure 23. Weigh Scales Using the AD7780
相關PDF資料 |
PDF描述 |
|---|---|
| AD7781CRZ | IC ADC 20BIT 1CH LP SD 14SOIC |
| AD7782BRUZ | IC ADC 24BIT 2CHAN 16TSSOP |
| AD7783BRU | IC ADC 24BIT 2CH R-R 16-TSSOP |
| AD7785BRUZ-REEL | IC ADC 20BIT 3CH LN LP 16-TSSOP |
| AD7787BRMZ | IC ADC 24BIT 2CH LP SIG 10MSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7781 | 制造商:AD 制造商全稱:Analog Devices 功能描述:20-Bit, Pin-Programmable, Low Power Sigma-Delta ADC |
| AD7781BRUZ | 功能描述:IC ADC 20BIT 1CH LP SD 16TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6 |
| AD7781BRUZ-REEL | 功能描述:IC ADC 20BIT 1CH LP SD 16TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:2,500 系列:- 位數:16 采樣率（每秒）:15 數據接口:MICROWIRE?，串行，SPI? 轉換器數目:1 功率耗散（最大）:480µW 電壓電源:單電源 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:38-WFQFN 裸露焊盤 供應商設備封裝:38-QFN（5x7） 包裝:帶卷 (TR) 輸入數目和類型:16 個單端，雙極；8 個差分，雙極 配用:DC1011A-C-ND - BOARD DELTA SIGMA ADC LTC2494 |
| AD7781BRZ | 功能描述:IC ADC 20BIT 1CH LP SD 14SOIC RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
| AD7781BRZ | 制造商:Analog Devices 功能描述:IC ADC 20BIT 16.7SPS SOIC-14 |
發布緊急采購，3分鐘左右您將得到回復。