參數資料
型號: AD7747ARUZ
廠商: Analog Devices Inc
文件頁數: 17/28頁
文件大?。?/td> 0K
描述: IC CONV 24BIT CAP-DGTL 16-TSSOP
標準包裝: 96
類型: 電容數字轉換器
分辨率(位): 24 b
數據接口: 串行
電壓電源: 單電源
電源電壓: 2.7 V ~ 5.25 V
工作溫度: -40°C ~ 125°C
安裝類型: 表面貼裝
封裝/外殼: 16-TSSOP(0.173",4.40mm 寬)
供應商設備封裝: 16-TSSOP
包裝: 管件
產品目錄頁面: 781 (CN2011-ZH PDF)
配用: EVAL-AD7747EBZ-ND - BOARD EVAL FOR AD7747
其它名稱: Q23139198
AD7747
Rev. 0 | Page 24 of 28
CAPACITIVE SYSTEM OFFSET CALIBRATION
The capacitive offset is dominated by the parasitic offset in the
application, such as the initial capacitance of the sensor, any
parasitic capacitance of tracks on the board, and the capacitance
of any other connections between the sensor and the CDC.
Therefore, the AD7747 is not factory calibrated for capacitive
offset. It is the user’s responsibility to calibrate the system
capacitance offset in the application.
Any offset in the capacitance input larger than ±1 pF should
first be removed using the on-chip CAPDACs. The small offset
within ±1 pF can then be removed by using the capacitance
offset calibration register.
One method of adjusting the offset is to connect a zero-scale
capacitance to the input and execute the capacitance offset
calibration mode. The calibration sets the midpoint of the
±8.192 pF range (that is, Output Code 0x800000) to that
zero-scale input.
Another method is to calculate and write the offset calibration
register value; the LSB value is 31.25 aF (8.192 pF/217).
The offset calibration register is reloaded by the default value at
power-on or after reset. Therefore, if the offset calibration is not
repeated after each system power-up, the calibration coefficient
value should be stored by the host controller and reloaded as
part of the AD7747 setup.
INTERNAL TEMPERATURE SENSOR
DIGITAL
FILTER
AND
SCALING
24-BIT Σ-Δ
MODULATOR
CLOCK
GENERATOR
INTERNAL TEMPERATURE SENSOR
0
54
69
-0
26
VOLTAGE
REFERENCE
DATA
IN × I
ΔVBE
VDD
Figure 36. Internal Temperature Sensor
The temperature sensing method used in the AD7747 is to
measure a difference in ΔVBE voltage of a transistor operated at
two different currents (see Figure 36). The ΔVBE change with
temperature is linear and can be expressed as
)
ln(
)
(
N
q
KT
n
V
f
BE
×
=
Δ
where:
K is Boltzmann’s constant (1.38 × 1023).
T is the absolute temperature in Kelvin.
q is the charge on the electron (1.6 × 1019 coulombs).
N is the ratio of the two currents.
nf is the ideality factor of the thermal diode.
The AD7747 uses an on-chip transistor to measure the
temperature of the silicon chip inside the package. The Σ-Δ
ADC converts the ΔVBE to digital; the data are scaled using
factory calibration coefficients. Thus, the output code is
proportional to temperature.
()
4096
2048
=
°
Code
C
e
Temperatur
The AD7747 has a low power consumption resulting in only a
small effect due to the part self-heating (less than 0.5°C at
VDD = 5 V).
If the capacitive sensor can be considered to be at the same
temperature as the AD7747 chip, the internal temperature
sensor can be used as a system temperature sensor. That means
the complete system temperature drift compensation can be
based on the AD7747 internal temperature sensor without need
for any additional external components. See
EXTERNAL TEMPERATURE SENSOR
DIGITAL
FILTER
AND
SCALING
24-BIT Σ-Δ
MODULATOR
CLOCK
GENERATOR
EXTERNAL
TEMPERATURE
SENSOR
0
5
469
-02
7
VOLTAGE
REFERENCE
DATA
I ... N × I
ΔVBE
VDD
VIN(–)
VIN(+)
RS2
RS1
2N3906
Figure 37. Transistor as an External Temperature Sensor
The AD7747 provides the option of using an external transistor
as a temperature sensor in the system. The ΔVBE method, which
is similar to the internal temperature sensor method, is used.
However, it is modified to compensate for the serial resistance
of connections to the sensor. Total serial resistance (RS1 + RS2 in
Figure 37) up to 100 Ω is compensated. The VIN() pin must
be grounded for proper external temperature sensor operation.
The AD7747 is factory calibrated for Transistor 2N3906 with
the ideality factor nf = 1.008.
相關PDF資料
PDF描述
MS27474E8B35P CONN RCPT 6POS JAM NUT W/PINS
AD7745ARUZ IC CONV 1CH CAP TO DGTL 16TSSOP
VI-B12-IU-S CONVERTER MOD DC/DC 15V 200W
VE-B12-IU-S CONVERTER MOD DC/DC 15V 200W
AD9823KRUZ IC CDS FOR DGTL CAMERA 14-TSSOP
相關代理商/技術參數
參數描述
AD7747ARUZ-REEL 功能描述:IC CONV CAP TO DIG 24BIT 16TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - ADCs/DAC - 專用型 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 類型:數據采集系統(DAS) 分辨率(位):16 b 采樣率(每秒):21.94k 數據接口:MICROWIRE?,QSPI?,串行,SPI? 電壓電源:模擬和數字 電源電壓:1.8 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:40-WFQFN 裸露焊盤 供應商設備封裝:40-TQFN-EP(6x6) 包裝:托盤
AD7747ARUZ-REEL7 功能描述:IC CONV CAP TO DIG 24BIT 16TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - ADCs/DAC - 專用型 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 類型:數據采集系統(DAS) 分辨率(位):16 b 采樣率(每秒):21.94k 數據接口:MICROWIRE?,QSPI?,串行,SPI? 電壓電源:模擬和數字 電源電壓:1.8 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:40-WFQFN 裸露焊盤 供應商設備封裝:40-TQFN-EP(6x6) 包裝:托盤
AD7748BSTZ 制造商:Analog Devices 功能描述:
AD774B 制造商:AD 制造商全稱:Analog Devices 功能描述:Complete 12-Bit A/D Converters