- 您現在的位置：買賣IC網 > PDF目錄1892 > AD7747ARUZ-REEL7 (Analog Devices Inc)IC CONV CAP TO DIG 24BIT 16TSSOP PDF資料下載
參數資料
| 型號： | AD7747ARUZ-REEL7 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 17/28頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC CONV CAP TO DIG 24BIT 16TSSOP |
| 標準包裝： | 1,000 |
| 類型： | 電容數字轉換器 |
| 分辨率（位）： | 24 b |
| 數據接口： | 串行 |
| 電壓電源： | 單電源 |
| 電源電壓： | 2.7 V ~ 5.25 V |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 16-TSSOP |
| 包裝： | 帶卷 (TR) |
| 配用： | EVAL-AD7747EBZ-ND - BOARD EVAL FOR AD7747 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
AD7747
Rev. 0 | Page 24 of 28
CAPACITIVE SYSTEM OFFSET CALIBRATION
The capacitive offset is dominated by the parasitic offset in the
application, such as the initial capacitance of the sensor, any
parasitic capacitance of tracks on the board, and the capacitance
of any other connections between the sensor and the CDC.
Therefore, the AD7747 is not factory calibrated for capacitive
offset. It is the user’s responsibility to calibrate the system
capacitance offset in the application.
Any offset in the capacitance input larger than ±1 pF should
first be removed using the on-chip CAPDACs. The small offset
within ±1 pF can then be removed by using the capacitance
offset calibration register.
One method of adjusting the offset is to connect a zero-scale
capacitance to the input and execute the capacitance offset
calibration mode. The calibration sets the midpoint of the
±8.192 pF range (that is, Output Code 0x800000) to that
zero-scale input.
Another method is to calculate and write the offset calibration
register value; the LSB value is 31.25 aF (8.192 pF/217).
The offset calibration register is reloaded by the default value at
power-on or after reset. Therefore, if the offset calibration is not
repeated after each system power-up, the calibration coefficient
value should be stored by the host controller and reloaded as
part of the AD7747 setup.
INTERNAL TEMPERATURE SENSOR
DIGITAL
FILTER
AND
SCALING
24-BIT Σ-Δ
MODULATOR
CLOCK
GENERATOR
INTERNAL TEMPERATURE SENSOR
0
54
69
-0
26
VOLTAGE
REFERENCE
DATA
IN × I
ΔVBE
VDD
Figure 36. Internal Temperature Sensor
The temperature sensing method used in the AD7747 is to
measure a difference in ΔVBE voltage of a transistor operated at
temperature is linear and can be expressed as
)
ln(
)
(
N
q
KT
n
V
f
BE
×
=
Δ
where:
K is Boltzmann’s constant (1.38 × 1023).
T is the absolute temperature in Kelvin.
q is the charge on the electron (1.6 × 1019 coulombs).
N is the ratio of the two currents.
nf is the ideality factor of the thermal diode.
The AD7747 uses an on-chip transistor to measure the
temperature of the silicon chip inside the package. The Σ-Δ
ADC converts the ΔVBE to digital; the data are scaled using
factory calibration coefficients. Thus, the output code is
proportional to temperature.
()
4096
2048
=
°
Code
C
e
Temperatur
The AD7747 has a low power consumption resulting in only a
small effect due to the part self-heating (less than 0.5°C at
VDD = 5 V).
If the capacitive sensor can be considered to be at the same
temperature as the AD7747 chip, the internal temperature
sensor can be used as a system temperature sensor. That means
the complete system temperature drift compensation can be
based on the AD7747 internal temperature sensor without need
for any additional external components. See
Figure 17 in the
Typical Performance Characteristics section.
EXTERNAL TEMPERATURE SENSOR
DIGITAL
FILTER
AND
SCALING
24-BIT Σ-Δ
MODULATOR
CLOCK
GENERATOR
EXTERNAL
TEMPERATURE
SENSOR
0
5
469
-02
7
VOLTAGE
REFERENCE
DATA
I ... N × I
ΔVBE
VDD
VIN(–)
VIN(+)
RS2
RS1
2N3906
Figure 37. Transistor as an External Temperature Sensor
The AD7747 provides the option of using an external transistor
as a temperature sensor in the system. The ΔVBE method, which
is similar to the internal temperature sensor method, is used.
However, it is modified to compensate for the serial resistance
of connections to the sensor. Total serial resistance (RS1 + RS2 in
Figure 37) up to 100 Ω is compensated. The VIN() pin must
be grounded for proper external temperature sensor operation.
The AD7747 is factory calibrated for Transistor 2N3906 with
the ideality factor nf = 1.008.
See Figure 18 in the Typical Performance Characteristics section.
相關PDF資料 |
PDF描述 |
|---|---|
| AD7808BR | IC DAC 10BIT 3.3V OCTAL 24-SOIC |
| AD7849CR | IC DAC 16BIT SRL INP 20-SOIC |
| AD7868BNZ | IC I/O PORT 12BIT ANLG 24-DIP |
| AD7869JRZ | IC I/O PORT 14BIT ANLG 28SOIC |
| AD7874SE | IC DAS 12BIT 4CH 5V 28-CLCC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7748BSTZ | 制造商:Analog Devices 功能描述: |
| AD774B | 制造商:AD 制造商全稱:Analog Devices 功能描述:Complete 12-Bit A/D Converters |
| AD774BAD | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| AD774BAR | 功能描述:IC ADC 12BIT W/BUFF REF 28-SOIC RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
發布緊急采購，3分鐘左右您將得到回復。