- 您現在的位置：買賣IC網 > PDF目錄10135 > AD7690BRMZ-RL7 (Analog Devices Inc)IC ADC 18BIT 400KSPS 10-MSOP PDF資料下載
參數資料
| 型號： | AD7690BRMZ-RL7 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 16/24頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 18BIT 400KSPS 10-MSOP |
| 標準包裝： | 1,000 |
| 系列： | PulSAR® |
| 位數： | 18 |
| 采樣率（每秒）： | 400k |
| 數據接口： | DSP，MICROWIRE?，QSPI?，串行，SPI? |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 20mW |
| 電壓電源： | 模擬和數字 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 10-TFSOP，10-MSOP（0.118"，3.00mm 寬） |
| 供應商設備封裝： | 10-MSOP |
| 包裝： | 帶卷 (TR) |
| 輸入數目和類型： | 1 個差分，雙極 |
AD7690
Rev. B | Page 23 of 24
APPLICATION HINTS
LAYOUT
The printed circuit board that houses the AD7690 should be
designed so that the analog and digital sections are separated
and confined to certain areas of the board. The pinout of the
AD7690, with its analog signals on the left side and its digital
signals on the right side, eases this task.
Avoid running digital lines under the device because these
couple noise onto the die unless a ground plane under the
AD7690 is used as a shield. Fast switching signals, such as CNV
or clocks, should not run near analog signal paths. Crossover of
digital and analog signals should be avoided.
At least one ground plane should be used. It can be common or
split between the digital and analog sections. In the latter case,
the planes should be joined underneath the AD7690s.
The AD7690 voltage reference input REF has a dynamic input
impedance and should be decoupled with minimal parasitic
inductances. This is done by placing the reference decoupling
ceramic capacitor close to, ideally right up against, the REF and
GND pins and connecting them with wide, low impedance traces.
Finally, the AD7690 VDD and VIO power supplies should be
decoupled with ceramic capacitors, typically 100 nF, placed
close to the AD7690 and connected using short, wide traces to
provide low impedance paths and to reduce the effect of glitches
on the power supply lines.
An example of a layout following these rules is shown in
Figure 46 and Figure 47.
EVALUATING THE AD7690’S PERFORMANCE
Other recommended layouts for the AD7690 are outlined
in the documentation of the evaluation board (EVAL-
AD7690CBZ). The evaluation board package includes
a fully assembled and tested evaluation board, documentation,
and software for controlling the board from a PC via the
0
57
92
-0
23
Figure 46. Example Layout of the AD7690 (Top Layer)
05
79
2-
0
24
Figure 47. Example Layout of the AD7690 (Bottom Layer)
相關PDF資料 |
PDF描述 |
|---|---|
| IDT7200L15SOI8 | IC MEM FIFO 256X9 15NS 28-SOIC |
| ADM237LJRZ | IC TXRX RS-232 5:3 5V LP 24SOIC |
| IDT7200L15SOGI8 | IC MEM FIFO 256X9 15NS 28-SOIC |
| VE-J4V-MX-S | CONVERTER MOD DC/DC 5.8V 75W |
| MS3102E36-3S | CONN RCPT 6POS BOX MNT W/SCKT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7690BRNZ | 制造商:Analog Devices 功能描述: |
| AD7691 | 制造商:AD 制造商全稱:Analog Devices 功能描述:16-Bit Lower Power |
| AD76911 | 制造商:AD 制造商全稱:Analog Devices 功能描述:18-Bit, 2 MSPS PulSAR 15 mW ADC in LFCSP (QFN) |
| AD7691BCPZ-R2 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Analog Devices 功能描述: |
| AD7691BCPZRL | 功能描述:IC ADC 18BIT SAR 250KSPS 10LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:PulSAR® 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極 |
發布緊急采購，3分鐘左右您將得到回復。