參數資料
型號： AD7687BRMZRL7
廠商： Analog Devices Inc
文件頁數： 17/28頁
文件大?。?/td> 0K
描述： IC ADC 16BIT 250KSPS 10MSOP
標準包裝： 1,000
系列： PulSAR®
位數： 16
采樣率（每秒）： 250k
數據接口： DSP，MICROWIRE?，QSPI?，串行，SPI?
轉換器數目： 1
功率耗散（最大）： 12.5mW
電壓電源： 模擬和數字
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 10-TFSOP，10-MSOP（0.118"，3.00mm 寬）
供應商設備封裝： 10-MSOP
包裝： 帶卷 (TR)
輸入數目和類型： 1 個差分，雙極
配用： EVAL-AD7687CBZ-ND - BOARD EVALUATION FOR AD7687
AD7687
Data Sheet
Rev. B | Page 24 of 28
APPLICATION HINTS
LAYOUT
The printed circuit board that houses the AD7687 should be
designed so that the analog and digital sections are separated
and confined to certain areas of the board. The pinout of the
AD7687, with all its analog signals on the left side and all its
digital signals on the right side, eases this task.
Avoid running digital lines under the device because these
couple noise onto the die, unless a ground plane under the
AD7687 is used as a shield. Fast switching signals, such as CNV
or clocks, should never run near analog signal paths. Crossover
of digital and analog signals should be avoided
At least one ground plane should be used. It could be common
or split between the digital and analog sections. In the latter
case, the planes should be joined underneath the AD7687s.
The AD7687 voltage reference input REF has a dynamic input
impedance and should be decoupled with minimal parasitic
inductances. This is done by placing the reference decoupling
ceramic capacitor close to, and ideally right up against, the REF
and GND pins and connecting it with wide, low impedance
traces.
Finally, the power supplies VDD and VIO of the AD7687
should be decoupled with ceramic capacitors (typically 100 nF)
placed close to the AD7687 and connected using short and wide
traces to provide low impedance paths and reduce the effect of
glitches on the power supply lines.
An example of layout following these rules is shown in
EVALUATING THE AD7687’S PERFORMANCE
Other recommended layouts for the AD7687 are outlined
in the documentation of the evaluation board for the AD7687
(EVAL-AD7687). The evaluation board package includes
a fully assembled and tested evaluation board, documentation,
and software for controlling the board from a PC via the
EVAL-CONTROL BRD3.
02972-046
Figure 47. Example of Layout of the AD7687 (Top Layer)
02972-047
Figure 48. Example of Layout of the AD7687 (Bottom Layer)
相關PDF資料
PDF描述
AD9221ARZ-REEL IC ADC 12BIT 1.5MSPS 28SOIC
MS27472E20B41P CONN RCPT 41POS WALL MT W/PINS
13380-10SG-326 CONN PLUG 10POS CABLE SKT
LTC1417AIGN IC A/D CONV 14BIT SAMPLNG 16SSOP
MS27467T11B99P CONN PLUG 7POS STRAIGHT W/PINS
相關代理商/技術參數
參數描述
AD7688 制造商:AD 制造商全稱:Analog Devices 功能描述:16-Bit, +/-0.65 LSB INL, 500 kSPS PulSAR Differential ADC in MSOP/QFN
AD76881 制造商:AD 制造商全稱:Analog Devices 功能描述:18-Bit, 2 MSPS PulSAR 15 mW ADC in LFCSP (QFN)
AD7688ARM 制造商:Analog Devices 功能描述:16-BIT DIFF, 550KSPS SERIAL MSOP ADC - Bulk
AD7688BCPZ-R2 制造商:Rochester Electronics LLC 功能描述: 制造商:Analog Devices 功能描述:
AD7688BCPZRL 功能描述:IC ADC 16BIT SAR 500KSPS 10LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:PulSAR® 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*