- 您現在的位置：買賣IC網 > PDF目錄375237 > AD7612BSTZ (ANALOG DEVICES INC) 16-Bit, 750 kSPS, Unipolar/Bipolar Programmable Input PulSAR ADC PDF資料下載
參數資料
| 型號： | AD7612BSTZ |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | ADC |
| 英文描述： | 16-Bit, 750 kSPS, Unipolar/Bipolar Programmable Input PulSAR ADC |
| 中文描述： | 1-CH 16-BIT SUCCESSIVE APPROXIMATION ADC, PARALLEL ACCESS, PQFP48 |
| 封裝： | LEAD FREE, MS-026BBC, LQFP-48 |
| 文件頁數： | 31/32頁 |
| 文件大小： | 587K |
| 代理商： | AD7612BSTZ |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁當前第31頁第32頁
AD7612
APPLICATION INFORMATION
LAYOUT GUIDELINES
While the AD7612 has very good immunity to noise on the
power supplies, exercise care with the grounding layout. To facil-
itate the use of ground planes that can be easily separated, design
the printed circuit board that houses the AD7612 so that the
analog and digital sections are separated and confined to certain
areas of the board. Digital and analog ground planes should be
joined in only one place, preferably underneath the AD7612, or
as close as possible to the AD7612. If the AD7612 is in a system
where multiple devices require analog-to-digital ground connec-
tions, the connections should still be made at one point only, a
star ground point, established as close as possible to the AD7612.
Rev. 0 | Page 31 of 32
To prevent coupling noise onto the die, avoid radiating noise,
and to reduce feedthrough:
Do not run digital lines under the device.
Do run the analog ground plane under the AD7612.
Do shield fast switching signals, like CNVST or clocks, with
digital ground to avoid radiating noise to other sections of
the board, and never run them near analog signal paths.
Avoid crossover of digital and analog signals.
Run traces on different but close layers of the board, at right
angles to each other, to reduce the effect of feedthrough through
the board.
The power supply lines to the AD7612 should use as large a trace
as possible to provide low impedance paths and reduce the effect
of glitches on the power supply lines. Good decoupling is also
important to lower the impedance of the supplies presented to
the AD7612, and to reduce the magnitude of the supply spikes.
Decoupled ceramic capacitors, typically 100 nF, should be placed
on each of the power supplies pins, AVDD, DVDD, and OVDD,
VCC, and VEE. The capacitors should be placed close to, and
ideally right up against, these pins and their corresponding ground
pins. Additionally, low ESR 10 μF capacitors should be located
in the vicinity of the ADC to further reduce low frequency ripple.
The DVDD supply of the AD7612 can be either a separate supply
or come from the analog supply, AVDD, or from the digital inter-
face supply, OVDD. When the system digital supply is noisy, or
fast switching digital signals are present, and no separate supply is
available, it is recommended to connect the DVDD digital supply
to the analog supply AVDD through an RC filter, and to connect
the system supply to the interface digital supply OVDD and the
remaining digital circuitry. See Figure 27 for an example of this
configuration. When DVDD is powered from the system supply,
it is useful to insert a bead to further reduce high frequency spikes.
The AD7612 has four different ground pins: REFGND, AGND,
DGND, and OGND.
REFGND senses the reference voltage and, because it carries
pulsed currents, should be a low impedance return to the
reference.
AGND is the ground to which most internal ADC analog
signals are referenced; it must be connected with the least
resistance to the analog ground plane.
DGND must be tied to the analog or digital ground plane
depending on the configuration.
OGND is connected to the digital system ground.
The layout of the decoupling of the reference voltage is important.
To minimize parasitic inductances, place the decoupling capacitor
close to the ADC and connect it with short, thick traces.
EVALUATING PERFORMANCE
A recommended layout for the AD7612 is outlined in the EVAL-
AD7612CB evaluation board documentation. The evaluation
board package includes a fully assembled and tested evaluation
board, documentation, and software for controlling the board
from a PC via the EVAL-CONTROL BRD3.
相關PDF資料 |
PDF描述 |
|---|---|
| AD7612BSTZ-RL | 16-Bit, 750 kSPS, Unipolar/Bipolar Programmable Input PulSAR ADC |
| AD7622 | 16-Bit, 750 kSPS, Unipolar/Bipolar Programmable Input PulSAR ADC |
| AD7623 | 16-Bit, 750 kSPS, Unipolar/Bipolar Programmable Input PulSAR ADC |
| AD7643 | 16-Bit, 750 kSPS, Unipolar/Bipolar Programmable Input PulSAR ADC |
| AD7656 | 250 kSPS, 6-Channel,Simultaneous Sampling, Bipolar 12/14/16-Bit ADC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7612BSTZ-RL | 功能描述:IC ADC 16BIT 750KSPS SAR 48-LQFP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:PulSAR® 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
| AD7616BSTZ | 功能描述:16 Bit Analog to Digital Converter 16 Input 2 SAR 80-LQFP (14x14) 制造商:analog devices inc. 系列:- 包裝:托盤 零件狀態:在售 位數:16 采樣率（每秒）:1M 輸入數:16 輸入類型:差分 數據接口:SPI，并聯，DSP 配置:MUX-S/H-ADC 無線電 - S/H:ADC:1:1 A/D 轉換器數:2 架構:SAR 參考類型:外部， 內部 電壓 - 電源，模擬:5V 電壓 - 電源，數字:2.3 V ~ 3.6 V 特性:同步采樣 工作溫度:-40°C ~ 125°C 封裝/外殼:80-LQFP 供應商器件封裝:80-LQFP（14x14） 標準包裝:1 |
| AD7616BSTZ-RL | 功能描述:16 Bit Analog to Digital Converter 16 Input 2 SAR 80-LQFP (14x14) 制造商:analog devices inc. 系列:- 包裝:剪切帶（CT） 零件狀態:在售 位數:16 采樣率（每秒）:1M 輸入數:16 輸入類型:差分 數據接口:SPI，并聯，DSP 配置:MUX-S/H-ADC 無線電 - S/H:ADC:1:1 A/D 轉換器數:2 架構:SAR 參考類型:外部， 內部 電壓 - 電源，模擬:5V 電壓 - 電源，數字:2.3 V ~ 3.6 V 特性:同步采樣 工作溫度:-40°C ~ 125°C 封裝/外殼:80-LQFP 供應商器件封裝:80-LQFP（14x14） 標準包裝:1 |
| AD7616-PBSTZ | 功能描述:IC DAS ADC DUAL 16BIT 16CH 80LQF 制造商:analog devices inc. 系列:- 包裝:托盤 零件狀態:在售 位數:16 采樣率（每秒）:1M 輸入數:16 輸入類型:單端 數據接口:并聯 配置:MUX-ADC 無線電 - S/H:ADC:- A/D 轉換器數:2 架構:SAR 參考類型:外部， 內部 電壓 - 電源，模擬:4.75 V ~ 5.25 V 電壓 - 電源，數字:2.3 V ~ 3.6 V 特性:同步采樣 工作溫度:-40°C ~ 125°C 封裝/外殼:80-LQFP 供應商器件封裝:80-LQFP（14x14） 標準包裝:1 |
| AD7616-PBSTZ-RL | 功能描述:100KSPS 16 CH MUXED DUAL 16B SAR 制造商:analog devices inc. 系列:- 包裝:帶卷（TR） 零件狀態:在售 位數:16 采樣率（每秒）:1M 輸入數:16 輸入類型:單端 數據接口:并聯 配置:MUX-ADC 無線電 - S/H:ADC:- A/D 轉換器數:2 架構:SAR 參考類型:外部， 內部 電壓 - 電源，模擬:4.75 V ~ 5.25 V 電壓 - 電源，數字:2.3 V ~ 3.6 V 特性:同步采樣 工作溫度:-40°C ~ 125°C 封裝/外殼:80-LQFP 供應商器件封裝:80-LQFP（14x14） 標準包裝:1,000 |
發布緊急采購，3分鐘左右您將得到回復。