參數資料
型號： AD7612BCPZ
廠商： ANALOG DEVICES INC
元件分類： ADC
英文描述： 16-Bit, 750 kSPS, Unipolar/Bipolar Programmable Input PulSAR ADC
中文描述： 1-CH 16-BIT SUCCESSIVE APPROXIMATION ADC, PARALLEL ACCESS, QCC48
封裝： 7 X 7 MM, LEAD FREE, MO-220VKKD-2, LFCSP-48
文件頁數： 9/32頁
文件大?。?/td> 587K
代理商： AD7612BCPZ
AD7612
Pin No.
13
Rev. 0 | Page 9 of 32
Mnemonic
D4 or
EXT/INT
Type
1
DI/O
Description
In parallel mode, this output is used as Bit 4 of the parallel port data output bus.
Serial Data Clock Source Select. In serial mode, this input is used to select the internally generated
(master) or external (slave) serial data clock for the AD7612 output data.
When EXT/INT = low, master mode; the internal serial data clock is selected on SDCLK output.
When EXT/INT = high, slave mode; the output data is synchronized to an external clock signal (gated by CS)
connected to the SDCLK input.
In parallel mode, this output is used as Bit 5 of the parallel port data output bus.
Serial Data Invert Sync Select. In serial master mode (SER/PAR = high, EXT/INT = low). This input is used
to select the active state of the SYNC signal.
When INVSYNC = low, SYNC is active high.
When INVSYNC = high, SYNC is active low.
In parallel mode, this output is used as Bit 6 of the parallel port data output bus.
In all serial modes, invert SDCLK/SCCLK select. This input is used to invert both SDCLK and SCCLK.
When INVSCLK = low, the rising edge of SDCLK/SCCLK are used.
When INVSCLK = high, the falling edge of SDCLK/SCCLK are used.
In parallel mode, this output is used as Bit 7 of the parallel port data output bus.
Serial Data Read During Convert. In serial master mode (SER/PAR = high, EXT/INT = low) RDC is used to
select the read mode. Refer to the Master Serial Interface section.
When RDC = low, the current result is read after conversion. Note the maximum throughput is not
attainable in this mode.
When RDC = high, the previous conversion result is read during the current conversion.
Serial Data In. In serial slave mode (SER/PAR = high EXT/INT = high) SDIN can be used as a data input to
daisy-chain the conversion results from two or more ADCs onto a single SDOUT line. The digital data
level on SDIN is output on SDOUT with a delay of 16 SDCLK periods after the initiation of the read sequence.
Input/Output Interface Digital Power Ground. Ground reference point for digital outputs. Should be
connected to the system digital ground ideally at the same potential as AGND and DGND.
Input/Output Interface Digital Power. Nominally at the same supply as the supply of the host interface
2.5 V, 3 V, or 5 V and decoupled with 10 μF and 100 nF capacitors.
Digital Power. Nominally at 4.75 V to 5.25 V and decoupled with 10 μF and 100 nF capacitors. Can be
supplied from AVDD.
Digital Power Ground. Ground reference point for digital outputs. Should be connected to system
digital ground ideally at the same potential as AGND and OGND.
In parallel mode, this output is used as Bit 8 of the parallel port data output bus.
Serial Data output. In all serial modes this pin is used as the serial data output synchronized to SDCLK.
Conversion results are stored in an on-chip register. The AD7612 provides the conversion result, MSB
first, from its internal shift register. The data format is determined by the logic level of OB/2C.
When EXT/INT = low, (master mode) SDOUT is valid on both edges of SDCLK.
When EXT/INT = high, (slave mode).
When INVSCLK = low, SDOUT is updated on SDCLK rising edge.
When INVSCLK = high, SDOUT is updated on SDCLK falling edge.
In parallel mode, this output is used as Bit 9 of the parallel port data output bus.
Serial Data Clock. In all serial modes, this pin is used as the serial data clock input or output, dependent
on the logic state of the EXT/INT pin. The active edge where the data SDOUT is updated depends on
the logic state of the INVSCLK pin.
In parallel mode, this output is used as Bit 10 of the parallel port data output bus.
Serial Data Frame Synchronization. In serial master mode (SER/PAR = high, EXT/INT= low), this output
is used as a digital output frame synchronization for use with the internal data clock.
When a read sequence is initiated and INVSYNC = low, SYNC is driven high and remains high while the
SDOUT output is valid.
When a read sequence is initiated and INVSYNC = high, SYNC is driven low and remains low while the
SDOUT output is valid.
14
D5 or
INVSYNC
DI/O
15
D6 or
INVSCLK
DI/O
16
D7 or
RDC or
DI/O
SDIN
17
OGND
P
18
OVDD
P
19
DVDD
P
20
DGND
P
21
D8 or
SDOUT
DO
22
D9 or
SDCLK
DI/O
23
D10 or
SYNC
DO
相關PDF資料
PDF描述
AD7612BCPZ-RL 16-Bit, 750 kSPS, Unipolar/Bipolar Programmable Input PulSAR ADC
AD7612BSTZ 16-Bit, 750 kSPS, Unipolar/Bipolar Programmable Input PulSAR ADC
AD7612BSTZ-RL 16-Bit, 750 kSPS, Unipolar/Bipolar Programmable Input PulSAR ADC
AD7622 16-Bit, 750 kSPS, Unipolar/Bipolar Programmable Input PulSAR ADC
AD7623 16-Bit, 750 kSPS, Unipolar/Bipolar Programmable Input PulSAR ADC
相關代理商/技術參數
參數描述
AD7612BCPZ-RL 功能描述:IC ADC 16BIT 750KSPS SAR 48LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:PulSAR® 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極
AD7612BST 制造商:Analog Devices 功能描述:ADC 16BIT 750KSPS SAR 48-LQFP 制造商:Analog Devices 功能描述:ADC, 16BIT, 750KSPS, SAR, 48-LQFP
AD7612BSTZ 功能描述:IC ADC 16BIT 750KSPS SAR 48-LQFP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:PulSAR® 其它有關文件:TSA1204 View All Specifications 標準包裝:1 系列:- 位數:12 采樣率（每秒）:20M 數據接口:并聯 轉換器數目:2 功率耗散（最大）:155mW 電壓電源:模擬和數字 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-TQFP 供應商設備封裝:48-TQFP（7x7） 包裝:Digi-Reel® 輸入數目和類型:4 個單端，單極；2 個差分，單極 產品目錄頁面:1156 (CN2011-ZH PDF) 其它名稱:497-5435-6
AD7612BSTZ-RL 功能描述:IC ADC 16BIT 750KSPS SAR 48-LQFP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:PulSAR® 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極
AD7616BSTZ 功能描述:16 Bit Analog to Digital Converter 16 Input 2 SAR 80-LQFP (14x14) 制造商:analog devices inc. 系列:- 包裝:托盤 零件狀態:在售 位數:16 采樣率（每秒）:1M 輸入數:16 輸入類型:差分 數據接口:SPI，并聯，DSP 配置:MUX-S/H-ADC 無線電 - S/H:ADC:1:1 A/D 轉換器數:2 架構:SAR 參考類型:外部， 內部 電壓 - 電源，模擬:5V 電壓 - 電源，數字:2.3 V ~ 3.6 V 特性:同步采樣 工作溫度:-40°C ~ 125°C 封裝/外殼:80-LQFP 供應商器件封裝:80-LQFP（14x14） 標準包裝:1
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*