- 您現在的位置：買賣IC網 > PDF目錄1891 > AD7147A-1ACBZ500R7 (Analog Devices Inc)IC CDC 13CH I2C W/RAM 25WLCSP PDF資料下載
參數資料
| 型號： | AD7147A-1ACBZ500R7 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 26/69頁 |
| 文件大小： | 0K |
| 描述： | IC CDC 13CH I2C W/RAM 25WLCSP |
| 產品變化通告： | 8mm Carrier Tape Changes 28/Feb/2012 |
| 標準包裝： | 1 |
| 系列： | CapTouch™ |
| 類型： | 電容數字轉換器 |
| 分辨率（位）： | 16 b |
| 采樣率（每秒）： | 250k |
| 數據接口： | I²C，串行 |
| 電壓電源： | 單電源 |
| 電源電壓： | 2.6 V ~ 3.6 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 25-UFBGA，WLCSP |
| 供應商設備封裝： | 25-WLCSP |
| 包裝： | 標準包裝 |
| 其它名稱： | AD7147A-1ACBZ500R7DKR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁當前第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁
AD7147A
Rev. B | Page 31 of 68
OUTPUTS
ACSHIELD OUTPUT
The AD7147A measures the capacitance between CINx and
ground. Any capacitance to ground on the signal path between
the CINx pins and the sensor is included in the AD7147A
conversion result.
To eliminate stray capacitance to ground, the ACSHIELD signal should
be used to shield the connection between the sensor and CINx,
as shown in Figure 46. The plane around the sensors should also
be connected to ACSHIELD.
CIN0
CIN1
CIN2
CIN3
ACSHIELD
AD7147A
SE
N
SO
R
PC
B
GND
07
72
7-
0
46
Figure 46. ACSHIELD
The ACSHIELD output is the same signal waveform as the excitation
signal on CINx. Therefore, there is no ac current between CINx
and ACSHIELD, and any capacitance between these pins does not
affect the CINx charge transfer.
Using ACSHIELD eliminates capacitance-to-ground pickup, which
means that the AD7147A can be placed up to 10 cm away from
the sensors. This allows the AD7147A to be placed on a separate
PCB from that of the sensors if the connections between the
sensors and the CINx inputs are correctly shielded using
ACSHIELD.
GENERAL-PURPOSE INPUT/OUTPUT (GPIO)
The AD7147A has one GPIO pin. It can be configured as an input
or an output. The GPIO_SETUP Bits[13:12] in the STAGE_LOW_
INT_ENABLE register determine how the GPIO pin is configured.
Table 17. GPIO_SETUP Bits
GPIO_SETUP
GPIO Configuration
00
GPIO disabled
01
Input
10
Output low
11
Output high
When the GPIO is configured as an output, the voltage level on
the pin is set to either a low level or a high level, as defined by
the GPIO_SETUP bits (see Table 17).
The GPIO_INPUT_CONFIG bits in the STAGE_LOW_INT_
ENABLE register determine the response of the AD7147A to a
signal on the GPIO pin when the GPIO is configured as an
input. The GPIO can be configured as either active high or
active low, as well as either edge triggered or level triggered (see
Table 18).
Table 18. GPIO_INPUT_CONFIG Bits
GPIO_INPUT_CONFIG
GPIO Configuration
00
Triggered on negative level (active low)
01
Triggered on positive edge (active high)
10
Triggered on negative edge (active low)
11
Triggered on positive level (active high)
When GPIO is configured as an input, it triggers the interrupt
output on the AD7147A.
Table 16 lists the interrupt output behavior for each of the GPIO
configuration setups.
USING THE GPIO TO TURN ON/OFF AN LED
The GPIO on the AD7147A can be used to turn an LED on and
off by setting the GPIO as either output high or low. Setting the
GPIO output high turns on the LED; setting the GPIO output
low turns off the LED. The GPIO pin connects to a transistor
that provides the drive current for the LED. Suitable transistors
include the KTC3875 from Korea Electronics Co., Ltd. (KEC).
AD7147A
GPIO
VCC
KTC3875
OR SIMILAR
07
72
7-
0
47
Figure 47. Controlling an LED Using the GPIO
相關PDF資料 |
PDF描述 |
|---|---|
| AD7147WPACPZ-1500R | IC CAP-TO-DGTL CONV PROG 24LFCSP |
| AD7150BRMZ-REEL | IC CAP CONV 2CH ULT LP 10MSOP |
| AD7151BRMZ-REEL | IC CAP CONV 1CH ULT LP 10MSOP |
| AD7152BRMZ-REEL | IC CDC 12BIT 2/4CH 10MSOP |
| AD7156BCPZ-REEL | IC CDC 2CH 12BIT 1.8V 10-LFCSP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7147A-1ACBZ-RL | 功能描述:IC CDC 13CH I2C W/RAM 25WLCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - ADCs/DAC - 專用型 系列:CapTouch™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 類型:數據采集系統（DAS） 分辨率（位）:16 b 采樣率（每秒）:21.94k 數據接口:MICROWIRE?，QSPI?，串行，SPI? 電壓電源:模擬和數字 電源電壓:1.8 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:40-WFQFN 裸露焊盤 供應商設備封裝:40-TQFN-EP（6x6） 包裝:托盤 |
| AD7147AACBZ-500RL7 | 功能描述:IC CDC 13CH SPI W/RAM 25WLCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - ADCs/DAC - 專用型 系列:CapTouch™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 類型:數據采集系統（DAS） 分辨率（位）:16 b 采樣率（每秒）:21.94k 數據接口:MICROWIRE?，QSPI?，串行，SPI? 電壓電源:模擬和數字 電源電壓:1.8 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:40-WFQFN 裸露焊盤 供應商設備封裝:40-TQFN-EP（6x6） 包裝:托盤 |
| AD7147AACBZ-RL | 功能描述:IC CDC 13CH SPI W/RAM 25WLCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - ADCs/DAC - 專用型 系列:CapTouch™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 類型:數據采集系統（DAS） 分辨率（位）:16 b 采樣率（每秒）:21.94k 數據接口:MICROWIRE?，QSPI?，串行，SPI? 電壓電源:模擬和數字 電源電壓:1.8 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:40-WFQFN 裸露焊盤 供應商設備封裝:40-TQFN-EP（6x6） 包裝:托盤 |
| AD7147ACPZ-1500RL7 | 功能描述:IC CAP-TO-DGTL CONV PROG 24LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - ADCs/DAC - 專用型 系列:CapTouch™ 產品培訓模塊:Data Converter Basics 標準包裝:1 系列:- 類型:電機控制 分辨率（位）:12 b 采樣率（每秒）:1M 數據接口:串行，并聯 電壓電源:單電源 電源電壓:2.7 V ~ 3.6 V，4.5 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:100-TQFP 供應商設備封裝:100-TQFP（14x14） 包裝:剪切帶 (CT) 其它名稱:296-18373-1 |
| AD7147ACPZ-1500RL7 | 制造商:Analog Devices 功能描述:IC CDC 16BIT 111SPS LFCSP-24 |
發布緊急采購，3分鐘左右您將得到回復。