Maximum RL " />
參數資料
型號: AD694ARZ
廠商: Analog Devices Inc
文件頁數: 11/16頁
文件大小: 0K
描述: IC TRANSMITTER 4-20MA 16-SOIC
標準包裝: 47
類型: 電流發送器
輸入類型: 電壓
輸出類型: 電壓
電流 - 電源: 23mA
安裝類型: 表面貼裝
封裝/外殼: 16-SOIC(0.295",7.50mm 寬)
供應商設備封裝: 16-SOIC W
包裝: 管件
產品目錄頁面: 798 (CN2011-ZH PDF)
AD694
–4–
REV. B
Typical Minimum Supply Voltage vs. Temperature for 2 V
and 10 V Full Scale
Maximum RL vs. Supply Voltage
Voltage Reference Power Supply Rejection
IOUT: Voltage Compliance vs. Temperature
FUNCTIONAL DESCRIPTION
The operation of the AD694 can best be understood by dividing
the circuit into three functional parts (see Figure 1). First, a
single supply input amplifier buffers the high level, single-ended
input signal. The buffer amplifier drives the second section, a
voltage to current (V/I) converter, that makes a 0 to 16 mA sig-
nal dependent current.
Figure 1. Functional Block Diagram
The third section, a voltage reference and offset generator, is re-
sponsible for providing the 4 mA offset current signal.
BUFFER AMPLIFIER
The buffer amplifier is a single supply amplifier that may be
used as a unity gain buffer, an output amplifier for a current
output DAC, or as a gain block to amplify low level signals. The
amplifier’s PNP input stage has a common-mode range that ex-
tends from a few hundred mV below ground to within 2.5 V of
VS. The Class A output of the amplifier appears at Pin 1 (FB).
The output range extends from about 1 mV above common to
within 2.5 V of VS when the amplifier is operated as a follower.
The amplifier can source a maximum load of 5 k
, but can sink
only as much as its internal 10 k
pulldown resistor allows.
V/I CONVERTER
The ground referenced, input signal from the buffer amplifier is
converted to a 0 to 0.8 mA current by A2 and level shifted to
the positive supply. A current mirror then multiplies this signal
by a factor of 20 to make the signal current of 0 to 16 mA. This
technique allows the output stage to drive a load to within 2 V
of the positive supply (VS). Amplifier A2 forces the voltage at
Pin 1 across resistors R1 and R2 by driving the Darlington tran-
sistor, Q2. The high gain Darlington transmits the resistor cur-
rent to its collector and to R3 (900
). A3 forces the level
shifted signal across the 45
resistor to get a current gain of 20.
The transfer function of the V/I stage is therefore:
IV
R1
R2
OUT
PIN1
+
()
20
/
resulting in a 0-16 mA output swing for a 0–10 V input. Tying
Pin 4 (2 V FS) to ground shorts out R2 and results in a 2 V
full-scale input for a 16 mA output span.
The output stage of the V/I converter is of a unique design that
allows the IOUT pin to drive a load below the common (sub-
strate) potential of the device. The output transistor can always
drive a load to a point 36 V below the positive supply (VS). An
相關PDF資料
PDF描述
VE-J3J-IZ-B1 CONVERTER MOD DC/DC 36V 25W
AD9840AJSTZ IC CCD SIGNAL PROC 10BIT 48-LQFP
VE-J3J-IY-F3 CONVERTER MOD DC/DC 36V 50W
AD22057RZ IC AMP DIFF SINGLE-SUPPLY 8-SOIC
VE-J3J-IY-F2 CONVERTER MOD DC/DC 36V 50W
相關代理商/技術參數
參數描述
AD694ARZ-REEL 功能描述:IC TRANSMITTER 4-20MA 16SOIC RoHS:是 類別:集成電路 (IC) >> 接口 - 傳感器和探測器接口 系列:* 其它有關文件:Automotive Product Guide 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:74 系列:- 類型:觸控式傳感器 輸入類型:數字 輸出類型:數字 接口:JTAG,串行 電流 - 電源:100µA 安裝類型:表面貼裝 封裝/外殼:20-TSSOP(0.173",4.40mm 寬) 供應商設備封裝:20-TSSOP 包裝:管件
AD694BQ 功能描述:IC TRANSMITTER 4-20MA 16-CDIP RoHS:否 類別:集成電路 (IC) >> 接口 - 傳感器和探測器接口 系列:- 其它有關文件:Automotive Product Guide 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:74 系列:- 類型:觸控式傳感器 輸入類型:數字 輸出類型:數字 接口:JTAG,串行 電流 - 電源:100µA 安裝類型:表面貼裝 封裝/外殼:20-TSSOP(0.173",4.40mm 寬) 供應商設備封裝:20-TSSOP 包裝:管件
AD694BR 制造商:Analog Devices 功能描述:IC TRANSMITTER 4-20MA
AD694BR-REEL 制造商:Analog Devices 功能描述:SP Amp INSTR Amp Single 36V 16-Pin SOIC W T/R
AD694BR-REEL7 制造商:Analog Devices 功能描述:SP Amp INSTR Amp Single 36V 16-Pin SOIC W T/R 制造商:Rochester Electronics LLC 功能描述:- Tape and Reel