- 您現在的位置：買賣IC網 > PDF目錄3426 > AD606JN (Analog Devices Inc)IC AMP LOG LP 1.2MA 16DIP PDF資料下載
參數資料
| 型號： | AD606JN |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 11/12頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC AMP LOG LP 1.2MA 16DIP |
| 標準包裝： | 1 |
| 放大器類型： | 對數 |
| 電路數： | 1 |
| 輸出類型： | 差分 |
| 電流 - 輸入偏壓： | 4µA |
| 電流 - 電源： | 13mA |
| 電流 - 輸出 / 通道： | 1.2mA |
| 電壓 - 電源，單路/雙路(±)： | 4.5 V ~ 5.5 V |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 通孔 |
| 封裝/外殼： | 16-DIP（0.300"，7.62mm） |
| 供應商設備封裝： | 16-PDIP |
| 包裝： | 管件 |
AD606
REV. B
–8–
Adjustment Procedure
The slope and intercept adjustments interact; this can be mini-
mized by reducing the resistance of R1 and R2, chosen here to
minimize power drain. Calibration can be achieved in several
ways: The simplest is to apply an RF input at the desired oper-
ating frequency which is amplitude modulated at a relatively
low frequency (say 1 kHz to 10 kHz) to a known modulation
index. Thus, one might choose a ratio of 2 between the maxi-
mum and minimum levels of the RF amplitude, corresponding
to a 6 dB (strictly, 6.02 dB) change in input level. The average
RF level should be set to about –35 dBm (the midpoint of the
AD606’s range). R2 is then adjusted so that the 6 dB input
change results in the desired output voltage change, for ex-
ample, 226 mV at 37.5 mV/dB.
A better choice would be a 4:1 ratio (12.04 dB), to spread the
residual error out over a larger segment of the whole transfer
function. If a pulsed RF generator is available, the decibel incre-
ment might be enlarged to 20 dB or more. Using just a fixed-
level RF generator, the procedure is more time consuming, but
is carried out in just the same way: manually change the level by
a known number of decibels and adjust R2 until VLOG varies by
the corresponding voltage.
Having adjusted the slope, the intercept may now be simply ad-
justed using a known input level. A value of –35 dBm (397.6 mV
rms, or 400 mV to within 0.05 dB) is recommended, and if the
standard scaling is used (PX = –88.33 dBm, VY = 37.5 mV/dB),
then VLOG should be set to +2 V at this input level.
A Low Cost Audio Through RF Power Meter
Figure 7 shows a simple power meter that uses the AD606 and
an ICL7136 3-1/2 digit DMM IC driving an LCD readout. The
circuit operates from a single +5 V supply and provides direct
readout in dBm, with a resolution of 0.1 dBm.
In contrast to the limited dynamic range of the diode and
thermistor-styled sensors used in power meters, the AD606 can
measure signals from below –80 dBm to over +10 dBm. An
optional 50
termination is included in the figure; this could
form the lower arm of an external attenuator to accommodate
larger signal levels. By the simple expedient of using a 13 dB
attenuator, the LCD reading now becomes dBV (decibels above
1 V rms). This requires a series resistor of 174
, presenting an
input resistance of 224
. Alternatively, the input resistance can
be raised to 600
using 464 and 133 . It is important to
note that the AD606 inputs must be ac coupled. To extend the
low frequency range, use larger coupling capacitors and an
external loop filter, as outlined earlier.
The nominal 0.5 V to 3.5 V output of the AD606 (for a –75 dBm
to +5 dBm input) must be scaled and level shifted to fit within
the +1 V to +4.5 V common-mode range of the ICL7136 for
the +5 V supply used. This is achieved by the passive resistor
network of R1, R2, and R3 in conjunction with the bias net-
works of R4 through R7, which provide the ICL7136 with its
reference voltage, and R9 through R11, which set the intercept.
The ICL7136 measures the differential voltage between INHI
and INLO, which ranges from –75 mV to +5 mV for a
–75 dBm to +5 dBm input.
To calibrate the power meter, first adjust R6 for 100 mV be-
tween REF HI and REF LO. This sets the initial slope. Then
adjust R10 to set INLO 80 mV higher than INHI. This sets the
initial intercept. The slope and intercept may now be adjusted
using a calibrated signal generator as outlined in the previous
section.
To extend the low frequency limit of the system to audio fre-
quencies, simply change C1, C2, and C3 to 4.7
F.
The limiter output of the AD606 may be used to drive the high-
impedance input of a frequency counter.
51.1
C1*
100pF
dBm
INPUT
NC
200
+5V
INHI
COMM
PRUP
VPOS
FIL1
FIL2
LADJ
LMHI
INLO
COMM
ISUM
ILOG
BFIN
VLOG
OPCM
LMLO
AD606JN
NC
0.1 F
OPTIONAL
DRIVE TO
FREQUENCY
COUNTER
C3*
150pF
dBV
INPUT
174
C2*
100pF
NC
+5V
FOR AUDIO MEASUREMENTS CHANGE
C1, C2, AND C3 TO 4.7 F; POSITIVE POLARITY
CONNECT TO PINS 1, 16
*
NC = NO CONNECT
+5V
2.513V NOM
R8
100k
R9
5k
R10
100k
C4
1 F
+5V
R2
54.9k
R1
1M
R3
54.9k
2.433V NOM
80mV
FOR
0dBm
SIGNAL
INPUT
R5
4.32k
R6
500
R7
162
R4
4.99k
+5V
100mV
+5V
0.1 F
DISPLAY
–75.0
32
35
31
36
40
39
38
34
33
180k
50pF
0.1 F
1.8M
0.1 F
0.047 F
V–
INHI
INLO
REF HI
COMM
REF LO
ICL7136CPL
Figure 7. A Low Cost RF Power Meter
相關PDF資料 |
PDF描述 |
|---|---|
| TV02W101B-HF | TVS 200W 100V BIDIRECT SOD-123 |
| TV02W101B-G | TVS 200W 100V BIDIRECT SOD-123 |
| TLC2272CPSRG4 | IC OPAMP GP R-R 2.25MHZ 8SOIC |
| TV02W100B-HF | TVS 200W 10V BIDIRECT SOD-123 |
| 86584-214HLF | BERGSTIK II DR STRAIGHT RET |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD606JNZ | 功能描述:IC AMP LOG LP 1.2MA 16DIP RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:1 系列:- 放大器類型:通用 電路數:4 輸出類型:滿擺幅 轉換速率:0.028 V/µs 增益帶寬積:105kHz -3db帶寬:- 電流 - 輸入偏壓:3nA 電壓 - 輸入偏移:100µV 電流 - 電源:3.3µA 電流 - 輸出 / 通道:12mA 電壓 - 電源，單路/雙路(±):2.7 V ~ 12 V，±1.35 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:14-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:14-TSSOP 包裝:剪切帶 (CT) 其它名稱:OP481GRUZ-REELCT |
| AD606JNZ | 制造商:Analog Devices 功能描述:IC AMP ((NS)) |
| AD606JR | 功能描述:IC AMP LOG LP 1.2MA 16SOIC RoHS:否 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 其它有關文件:TS1854A View All Specifications 標準包裝:50 系列:- 放大器類型:通用 電路數:4 輸出類型:滿擺幅 轉換速率:0.25 V/µs 增益帶寬積:630kHz -3db帶寬:- 電流 - 輸入偏壓:16nA 電壓 - 輸入偏移:1000µV 電流 - 電源:162µA 電流 - 輸出 / 通道:48mA 電壓 - 電源，單路/雙路(±):1.8 V ~ 6 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:14-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:14-SO 包裝:管件 |
| AD606JR-REEL | 制造商:Analog Devices 功能描述:SP Amp LOG Amp Single 5.5V 16-Pin SOIC N T/R 制造商:Analog Devices 功能描述:SP AMP LOG AMP SGL 5.5V 16SOIC N - Tape and Reel |
| AD606JR-REEL7 | 功能描述:IC AMP LOG LP 1.2MA 16SOIC RoHS:否 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:50 系列:- 放大器類型:J-FET 電路數:2 輸出類型:- 轉換速率:3.5 V/µs 增益帶寬積:1MHz -3db帶寬:- 電流 - 輸入偏壓:30pA 電壓 - 輸入偏移:2000µV 電流 - 電源:200µA 電流 - 輸出 / 通道:- 電壓 - 電源，單路/雙路(±):7 V ~ 36 V，±3.5 V ~ 18 V 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:8-DIP（0.300"，7.62mm） 供應商設備封裝:8-PDIP 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。