- 您現在的位置：買賣IC網 > PDF目錄10979 > AD5930YRUZ (Analog Devices Inc)IC GEN PROG FREQ BURST 20TSSOP PDF資料下載
參數資料
| 型號： | AD5930YRUZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 8/28頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC GEN PROG FREQ BURST 20TSSOP |
| 產品培訓模塊： | Direct Digital Synthesis Tutorial Series (1 of 7): Introduction Direct Digital Synthesizer Tutorial Series (7 of 7): DDS in Action Direct Digital Synthesis Tutorial Series (3 of 7): Angle to Amplitude Converter Direct Digital Synthesis Tutorial Series (6 of 7): SINC Envelope Correction Direct Digital Synthesis Tutorial Series (4 of 7): Digital-to-Analog Converter Direct Digital Synthesis Tutorial Series (2 of 7): The Accumulator |
| 標準包裝： | 1 |
| 分辨率（位）： | 10 b |
| 主 fclk： | 50MHz |
| 調節字寬（位）： | 24 b |
| 電源電壓： | 2.3 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 20-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 20-TSSOP |
| 包裝： | 管件 |
| 產品目錄頁面： | 797 (CN2011-ZH PDF) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
AD5930
Data Sheet
Rev. | Page 16 of 28
THEORY OF OPERATION
The AD5930 is a general-purpose synthesized waveform
generator capable of providing digitally programmable
waveform sequences in both the frequency and time domain.
The device contains embedded digital processing to provide a
repetitive sweep of a user programmable frequency profile
allowing enhanced frequency control. Because the device is pre-
programmable, it eliminates continuous write cycles from a
DSP/μcontroller in generating a particular waveform.
THE FREQUENCY PROFILE
The frequency profile is defined by the start frequency (FSTART),
the frequency increment (Δf) and the number of increments
per sweep (NINCR). The increment interval between frequency
increments, tINT, is either user programmable with the interval
automatically determined by the device (auto-increment mode),
or externally controlled via a hardware pin (external increment
mode). For automatic update, the interval profile can either be
for a fixed number of clock periods or for a fixed number of
output waveform cycles.
In the auto-increment mode, a single pulse at the CTRL pin starts
and executes the frequency sweep. In the external increment
mode, the CTRL pin also starts the sweep, but the frequency
increment interval is determined by the time interval between
sequential 0/1 transitions on the CTRL pin. Furthermore, the
CTRL pin can be used to directly control the burst profile, where
during the input high time, the output waveform is present, and
during the input low time, the output is reset to midscale.
The frequency profile can be swept in two different modes: saw
sweep or triangular (up/down) sweep.
Saw-Sweep Mode
In the case of a saw sweep, the AD5930 repeatedly
sweeps between sweep start to sweep end, that is, from
FSTART incrementally to
FSTART + NINCR × Δf
This gives a saw-sweep cycle time of
(NINCR + 1) × tINT
FSTART
FSTART + F
FSTART + NINCR × F
MIDSCALE
05333-
009
Figure 31. Saw-Sweep Profile
Triangular-Sweep Mode
In the case of a triangular sweep, the AD5930 repeatedly
sweeps between sweep start to sweep end, that is, from FSTART
incrementally to
FSTART + NINCR × Δf
The triangular-sweep cycle time is given by
(1 + (2 × NINCR)) × tINT
FSTART
05333-
010
FSTART
FSTART + F
FSTART + NINCR × F
MIDSCALE
Figure 32. Triangular-Sweep Profile
OUTPUT MODES
The AD5930 offers two possible output modes: continuous
output mode and burst output mode. Both of these modes are
illustrated in Figure 33.
05333-
0
1
CONTINUOUS
MODE
BURST
MODE
1
2
NUMBER STEP CHANGES
tINT
TBURST
Figure 33. Continuous Mode and Burst Mode of the AD5930
Continuous Output Mode
In this mode, each frequency of the sweep is available for the
length of time programmed into the time interval (tINT) register.
This means the frequency swept output signal is continuously
available, and is therefore phase continuous at all frequency
increments.
To set up the AD5930 in continuous mode, the CW/BURST bit
(D7) in the control register must be set to 0. See the Activating
and Controlling the Sweep section for more details.
Burst Output Mode
In this mode, the AD5930 provides a programmable burst
of the waveform output for a fixed length of time (TBURST)
within the programmed increment interval (tINT). Then for
the remainder of the tINT interval, the output is reset to mid-
scale and remains there until the next frequency increment.
B
相關PDF資料 |
PDF描述 |
|---|---|
| S9S12HY64J0MLL | MCU 64K FLASH AUTO 100-LQFP |
| VI-21K-CU-S | CONVERTER MOD DC/DC 40V 200W |
| VI-21J-CU-S | CONVERTER MOD DC/DC 36V 200W |
| MCF51AC128CVFUE | MCU 32BIT 128K FLASH 64-QFP |
| MC9S08DZ128CLF | MCU 8BIT 128K FLASH 48-LQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD5930YRUZ-REEL7 | 功能描述:IC GEN PROG FREQ BURST 20TSSOP RoHS:是 類別:集成電路 (IC) >> 接口 - 直接數字合成 (DDS) 系列:- 產品變化通告:Product Discontinuance 27/Oct/2011 標準包裝:2,500 系列:- 分辨率（位）:10 b 主 fclk:25MHz 調節字寬（位）:32 b 電源電壓:2.97 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:帶卷 (TR) |
| AD5932 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Programmable Frequency Scan Waveform Generator |
| AD5932YRUZ | 功能描述:IC PROG WAVEFORM GEN SNGL16TSSOP RoHS:是 類別:集成電路 (IC) >> 接口 - 直接數字合成 (DDS) 系列:- 產品變化通告:Product Discontinuance 27/Oct/2011 標準包裝:2,500 系列:- 分辨率（位）:10 b 主 fclk:25MHz 調節字寬（位）:32 b 電源電壓:2.97 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:帶卷 (TR) |
| AD5932YRUZ-REEL7 | 功能描述:IC PROG WAVEFORM GENERAT 16TSSOP RoHS:是 類別:集成電路 (IC) >> 接口 - 直接數字合成 (DDS) 系列:- 產品變化通告:Product Discontinuance 27/Oct/2011 標準包裝:2,500 系列:- 分辨率（位）:10 b 主 fclk:25MHz 調節字寬（位）:32 b 電源電壓:2.97 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:帶卷 (TR) |
| AD5933 | 制造商:AD 制造商全稱:Analog Devices 功能描述:1 MSPS 12-Bit Impedance Converter, Network Analyzer |
發布緊急采購，3分鐘左右您將得到回復。