- 您現在的位置：買賣IC網 > PDF目錄5915 > AD5750-2BCPZ (Analog Devices Inc)IC CURR/VOLT OUT DRIVER 32LFCSP PDF資料下載
參數資料
| 型號： | AD5750-2BCPZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 18/36頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC CURR/VOLT OUT DRIVER 32LFCSP |
| 標準包裝： | 1 |
| 放大器類型： | 儀表 |
| 電路數： | 1 |
| 轉換速率： | 2 V/µs |
| 電流 - 電源： | 5.2mA |
| 電流 - 輸出 / 通道： | 24mA |
| 電壓 - 電源，單路/雙路(±)： | ±12 V ~ 24 V |
| 工作溫度： | -40°C ~ 105°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 32-VFQFN 裸露焊盤，CSP |
| 供應商設備封裝： | 32-LFCSP（5x5） |
| 包裝： | 托盤 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁當前第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
Data Sheet
AD5750/AD5750-1/AD5750-2
Rev. E | Page 25 of 36
CURRENT OUTPUT ARCHITECTURE
The voltage input from the analog input VIN pin (0 V to 4.096 V
either converted to a current (see Figure 53), which is then
mirrored to the supply rail so that the application simply sees
a current source output with respect to an internal reference
voltage, or it is buffered and scaled to output a software-selectable
unipolar or bipolar voltage range (see Figure 54). The reference
is used to provide internal offsets for range and gain scaling.
The selectable output range is programmable through the
digital interface.
Figure 53. Current Output Configuration
Figure 54. Voltage Output
DRIVING INDUCTIVE LOADS
When driving inductive or poorly defined loads, connect a 0.01 F
capacitor between IOUT and GND. This ensures stability with
loads beyond 50 mH. There is no maximum capacitance limit.
The capacitive component of the load may cause slower settling.
Voltage Output Amplifier
The voltage output amplifier is capable of generating both unipolar
and bipolar output voltages. It is capable of driving a load of 1 k
in parallel with 1.2 F (with an external compensation capacitor
on the COMP1 and COMP2 pins). The source and sink capabilities
of the output amplifier can be seen in Figure 16. The slew rate
is 2 V/s.
Internal to the device, there is a 2.5 M resistor connected
between the VOUT and VSENSE+ pins and, similarly, between
the VSENSE pin and the internal device ground. If a fault
condition occurs, these resistors act to protect the AD5750/
AD5750-1/AD5750-2 by ensuring that the amplifier loop is closed
so that the part does not enter into an open-loop condition.
The VSENSE pin can work in a common-mode range of ±3 V
with respect to the remote load ground point.
The current and voltage are output on separate pins and cannot
be output simultaneously. This allows the user to tie both the
current and voltage output pins together and configure the end
system as a single channel output.
Driving Large Capacitive Loads
The voltage output amplifier is capable of driving capacitive loads
of up to 1 F with the addition of a nonpolarized compensation
capacitor between the COMP1 and COMP2 pins.
Without the compensation capacitor, up to 20 nF capacitive loads
can be driven. Care should be taken to choose an appropriate
value for the CCOMP capacitor. This capacitor, while allowing the
and reduce overshoot, increases the settling time of the part
and, therefore, affects the bandwidth of the system. Considered
values of this capacitor should be in the range 100 pF to 4 nF,
depending on the trade-off required between settling time,
overshoot, and bandwidth.
hardware or software mode is loaded and set the power-up
conditions accordingly.
In software SPI mode, the power-up state of the output is
dependent on the state of the CLEAR pin. If the CLEAR pin is
pulled high, the part powers up, driving an active 0 V on the
output. If the CLEAR pin is pulled low, the part powers up with
the voltage output channel in tristate mode. In both cases, the
current output channel powers up in the tristate condition (0 mA).
This allows the voltage and current outputs to be connected
together, if desired.
To put the part into normal operation, the user must set the
OUTEN bit in the control register to enable the output and, in
the same write, set the output range configuration using the R3
to R0 range bits. If the CLEAR pin is still high (active) during
this write, the part automatically clears to its normal clear state
as defined by the programmed range and by the CLRSEL pin or
the CLRSEL bit (see the Asynchronous Clear (CLEAR) section
for more details). To operate the part in normal mode, take the
CLEAR pin low.
The CLEAR pin is typically driven directly from a microcontroller.
AD5750-2 supply may be independent of the microcontroller
power supply, connect a weak pull-up resistor to DVCC or a pull-
down resistor to ground to ensure that the correct power-up
condition is achieved independent of the microcontroller. A
10 k pull-up/pull-down resistor on the CLEAR pin should be
sufficient for most applications.
If hardware mode is selected, the part powers up to the conditions
defined by the R3 to R0 range bits and the status of the OUTEN
or CLEAR pin. It is recommended to keep the output disabled
when powering up the part in hardware mode.
IOUT
RANGE
SCALING
REXT1
IOUT
RSET
Vx
VSS
VDD
R1
R4
R2
R3
REXT2
IOUT
OPEN FAULT
VIN
VREF
RANGE DECODE
FROM INTERFACE
07268-
047
VOUT RANGE
SCALING
VSENSE+
VOUT
VSENSE–
VOUT
SHORT FAULT
RANGE DECODE
FROM INTERFACE
VIN
(0V TO 4.096V)
VREF
07268-
048
相關PDF資料 |
PDF描述 |
|---|---|
| GTCA38-501M-R10-FS2 | GAS TUBE 8MM 500V 20% 10KA |
| ADA4637-1ARZ | IC OPAMP JFET 79.9MHZ LN 8SOIC |
| HTSW-101-08-G-S | CONN HEADER 1POS .100" T/H GOLD |
| LT1491IS#PBF | IC OP-AMP R-R IN/OUT QUAD 14SOIC |
| ADA4897-2ARMZ | IC OPAMP RR 230MHZ LP 10MSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD5750-2BCPZ-RL7 | 功能描述:IC CURR/VOLT OUT DRVR 32LFCSP RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:73 系列:Over-The-Top® 放大器類型:通用 電路數:4 輸出類型:滿擺幅 轉換速率:0.07 V/µs 增益帶寬積:200kHz -3db帶寬:- 電流 - 輸入偏壓:1nA 電壓 - 輸入偏移:285µV 電流 - 電源:50µA 電流 - 輸出 / 通道:25mA 電壓 - 電源，單路/雙路(±):2 V ~ 44 V，±1 V ~ 22 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-WFDFN 裸露焊盤 供應商設備封裝:16-DFN-EP（5x3） 包裝:管件 |
| AD5750ACPZ | 功能描述:IC CURR/VOLT OUT DVR 32LFCSP RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:1 系列:- 放大器類型:通用 電路數:4 輸出類型:滿擺幅 轉換速率:0.028 V/µs 增益帶寬積:105kHz -3db帶寬:- 電流 - 輸入偏壓:3nA 電壓 - 輸入偏移:100µV 電流 - 電源:3.3µA 電流 - 輸出 / 通道:12mA 電壓 - 電源，單路/雙路(±):2.7 V ~ 12 V，±1.35 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:14-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:14-TSSOP 包裝:剪切帶 (CT) 其它名稱:OP481GRUZ-REELCT |
| AD5750ACPZ-REEL | 功能描述:IC CURR/VOLT OUT DVR 32LFCSP RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:100 系列:- 放大器類型:通用 電路數:1 輸出類型:- 轉換速率:0.2 V/µs 增益帶寬積:- -3db帶寬:- 電流 - 輸入偏壓:100pA 電壓 - 輸入偏移:30µV 電流 - 電源:380µA 電流 - 輸出 / 通道:- 電壓 - 電源，單路/雙路(±):±2 V ~ 18 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:8-SO 包裝:管件 |
| AD5750ACPZ-REEL7 | 功能描述:IC CURR/VOLT OUT DVR 32LFCSP RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:100 系列:- 放大器類型:通用 電路數:1 輸出類型:- 轉換速率:0.2 V/µs 增益帶寬積:- -3db帶寬:- 電流 - 輸入偏壓:100pA 電壓 - 輸入偏移:30µV 電流 - 電源:380µA 電流 - 輸出 / 通道:- 電壓 - 電源，單路/雙路(±):±2 V ~ 18 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:8-SO 包裝:管件 |
| AD5750BCPZ | 功能描述:IC CURR/VOLT OUT DVR 32LFCSP RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:150 系列:- 放大器類型:音頻 電路數:2 輸出類型:- 轉換速率:5 V/µs 增益帶寬積:12MHz -3db帶寬:- 電流 - 輸入偏壓:100nA 電壓 - 輸入偏移:500µV 電流 - 電源:6mA 電流 - 輸出 / 通道:50mA 電壓 - 電源，單路/雙路(±):4 V ~ 32 V，±2 V ~ 16 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:8-TSSOP 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。